Night Owl WNVR SERIES Bedienungsanleitung

QUICK SETUP GUIDE

www.NightOwlSP.com

WNVR SERIES

What’s in the Box

Monitor Router

Items Not Included

RESET LAN1 LAN2 LAN3 LAN4 WA N

Wireless NVR Camera(s)

USB Mouse (x1)

Disclaimer: Images and Quantities may vary by model.

Safety Stickers

Mounting Hardware

Wireless NVR Power

Adapter (x1)

9 ft. Camera

Power Adapter(s)

NVR Antenna (x2)

Camera Antenna

(1 per camera)

9 ft. Wi-Fi Extender

Antenna (1 for

every 4 cameras)

Package Contents

6 ft. RJ-45 Cable

(Ethernet) (x1)

6 ft. HDMI

(x1)

Wireless NVR Speciﬁcations

Audio Output – allows for the connection of an ampliﬁed speaker.

VGA Output – VGA output allows for a video connection. If the TV/Monitor

does not have an HDMI input but does have a VGA input, connect the VGA

cable from the VGA output port on the NVR to the VGA input port on your

TV/Monitor. (VGA cable not included)

HDMI Output – HDMI output allows for a video connection. If the TV/Monitor

has an HDMI input, connect the HDMI cable from the HDMI output port on

the NVR to the HDMI input port on your TV/Monitor.

RJ-45 (Ethernet) Port – The RJ-45 port will be used to connect the Wireless

NVR to your modem/router for remote viewing. Please note that your Wireless

NVR comes with built-in Wi-Fi for the cameras to transmit to the NVR.

However, you will need to manually connect the NVR to your modem/router

to remotely view on a smart device or PC/Mac®.

USB Ports – USB ports allow for the connection of a USB mouse and/or a

USB ﬂash drive. You will connect the included USB mouse to assist you in

navigating the NVR’s menu interface. You will connect a USB ﬂash drive

to download video ﬁles from the NVR for long term storage or sharing.

Power Input – Power input is used to connect the included 12V DC

power supply.

NVR Antenna Mount – for installation of two included NVR antennas.

Rear View

The maximum number of cameras you can connect to your Wireless NVR will be determined by

the number of channels.

AUDIO

OUTPUT

GROUND

VGA HDMI LAN USB POWER

12V

BEF

Positioning Your Wireless NVR and Cameras

NVR

Your wireless IP cameras will reach up

to 300 ft. wirelessly. Therefore, proper

placement of the wireless NVR in your

home will help ensure you achieve

maximum coverage.

Placing the wireless NVR centrally in

your home, will help make certain that

no matter where you mount your cameras,

they will be able to wirelessly connect.

POSITIONING YOUR WIRELESS NVR

Incorrect Placement

Correct Placement

Strength of Transmission Signal

Concrete Wall

Brick Wall

Glass with

Metal

Dry Wall

Wood Door

Glass Window

Mirror

Cinderblock

Strong

Weak

When your wireless signal is transmitted through various materials, such

as walls and windows, the signal strength is affected. Though the NVR

and wireless camera may be very close in proximity, you could still notice

high signal interference if the signal passes through certain obstacles. For

instance, if the signal passes through a concrete wall it will be severely

weakened. Please reference the below chart to see which obstacles highly

affect your signal and which do not.

How Obstacles Affect Your Signal Strength

Your Wireless NVR must be powered on

using the NVR power adapter. Similarly,

each wireless camera must be powered

with a camera power adapter. Though

these cameras wirelessly transmit video

to the NVR, they are not battery powered,

and must therefore be powered via the

included adapters. Each camera within

your system will come equipped with its’

own camera power adapter.

Powering the NVR and Wireless Cameras

NOTE: If your setup requires the signal to be transmitted through an obstacle that

severely weakens it, you can use the 9 ft. Wi-Fi Extender Antenna included with

your system. The Extender Antenna can be used to bypass the obstacle weakening

the signal. Simply replace the white Camera Antenna with the Extender Antenna

and then mount the Extender Antenna on the opposing side of the obstacle.

The Camera and NVR

power adapters will be

appropriately labeled.

Connecting Your System

Connect the two included antennas

to your wireless NVR. This will

ensure you achieve the maximum

wireless range for transmission

from your wireless cameras.

Plug the other end of the

HDMI cable into the back

of your TV or monitor.

Plug one end of the included

HDMI cable into the HDMI port

on the back of the Wireless NVR.

Plug one end of the included

Ethernet cable into the LAN port

on the back of the Wireless NVR.

Plug the other end of the

Ethernet cable into a port

on the back of your router.

5Ensure you are using the

correct power adapter when

setting up your system.

HDMI

ETHERNET

HDMI

You may also connect using VGA (not included)

Router Not

Included

ETHERNET

Connect the Wireless NVR power

adapter to the Power Input on

the rear of the Wireless NVR.

Connect the included camera

antenna to the antenna mount

on the camera.

Plug the Wireless NVR power

adapter into a surge protector or

Uninterruptible Power Supply

(UPS). (surge protector and

UPS not included)

To ensure all cameras are working

properly, please test them locally

before installing them.

Each camera comes equipped

with its’ own camera power

adapter. Connect the female

power cable coming from the

camera to the male power end

of the camera power adapter.

Next, plug the camera power

adapter into a wall outlet.

You should see each camera appear on your TV/Monitor. You may now

proceed to install your Wireless NVR cameras in the desired location.

Surge

Protector not

included

On the ‘Password Creation’ screen, please note the following:

Write your

password here:

Admin Account Creation

By default, the username will be ‘admin’. It must

remain ‘admin’ upon your initial account conﬁguration.

Recovery Email Address

Please ensure you provide a valid email address in

case your ever forget your account information.

Remember Your Password

Night Owl strongly recommends writing down your

password within the Quick Setup Guide. You will need

it every time you log into your Wireless NVR and to

remotely view on a Smart Device.

Important… Please Read

1When you power on the Wireless

NVR you will be prompted with

the following screen. Please follow

the instructions to complete the

Startup Wizard.

Startup Wizard

Booting Up for the First Time

At this stage of the Startup Wizard, you will be instructed on adjusting

the camera sensitivity and setting the Motion Detection Area. Having

your cameras in their ﬁnal position will be key.

So, if you would like to detect motion for the front door to your home,

place the camera to the side of the entrance.

The infrared sensor

works best for

‘side to side’

movement across

the cameras ﬁeld

of view as opposed

to movement

directly to or away

from the camera

When you reach the ‘Channel Settings’ screen, you will want to have

installed the cameras in their final position. Please make sure you

have mounted cameras at least 7ft. above the ground and angled them

slightly down.

This is the last screen you will

see when you have successfully

completed the Startup Wizard.

NOTE: For additional conﬁguration of your Wireless NVR, please refer to the

owner’s manual located on our support page at www.NightOwlSP.com.

Using Night Owl X

Download and Install Application

Download Night Owl X from the

App Store or Google Play Store

and install the application on

your device.

Create an account by entering an

email address for your username

and entering a password that is

between 6–20 characters long.

Click the link in the email

that was sent to you after

you created your account to

conﬁrm your email address.

Andere Handbücher für WNVR SERIES

Inhaltsverzeichnis

Andere Night Owl Sicherheitssystem Handbücher

Night Owl

Night Owl WNVR201 Series Bedienungsanleitung

Night Owl

Night Owl X Series Bedienungsanleitung

Night Owl

Night Owl NODVR108 Series Bedienungsanleitung

Night Owl

Night Owl S44245NHD Bedienungsanleitung

Night Owl

Night Owl DP2 Series Bedienungsanleitung

Night Owl

Night Owl Tiger-4500 Bedienungsanleitung

Night Owl

Night Owl HDA30 series Bedienungsanleitung

Night Owl

Night Owl THD301 Series Bedienungsanleitung

Night Owl

Night Owl HDA SERIES Bedienungsanleitung

Night Owl

Night Owl CAM-4PK-724 Bedienungsanleitung

Night Owl

Night Owl H2THD Bedienungsanleitung

Night Owl

Night Owl FS84500 Bedienungsanleitung

Night Owl

Night Owl Poseidon 85 Bedienungsanleitung

Night Owl

Night Owl K-16 Series Bedienungsanleitung

Night Owl

Night Owl NONB-44500 Bedienungsanleitung

Night Owl

Night Owl FS-8500 Bedienungsanleitung

Night Owl

Night Owl VDP2 Series Bedienungsanleitung

Night Owl

Night Owl WNVR-NC Series Bedienungsanleitung

Night Owl

Night Owl AHD10 Series Bedienungsanleitung

Night Owl

Night Owl C50XFR Series Bedienungsanleitung

Night Owl

Night Owl AHD7-882 Bedienungsanleitung

Night Owl

Night Owl HAWK-74250 Bedienungsanleitung

Night Owl

Night Owl CAM-WNVR2P-IN Bedienungsanleitung

Night Owl

Night Owl THD301 Series Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung