Nikon Eclipse Ti Series Bedienungsanleitung

M468 E os.r.Np.z

tilutilililtruffi[ilrililril

GGLIPSG 'Ti Series

Differential I nterference

Contrast Attachment

Instructions

lntroduction

Thank you lor purchasing a Nikon product.

This in;truction manual is written for users of Nikon Differential Interference Contrast Attachment for the

Inverted Microscope "ECLIPSE Ti Series."

To ensure correct usage, read this manual carefully before operating the product

. No part of this manual may be reproduced or transmitted in any lorm without prior written permission

lrom Nikon.

. The contents of this manual are subject to change without notice.

. Although every effort has been made to ensure the accuracy of lhis manual, errors or inconsislencies

may re-main. liyou note any points that are unclear or incorrect, please contact your nearesÎ Nikon

reDresentative,

. Some of the equipment described in this manual may not be included in the set you have purchased.

. lf you intend to use any olher equipmenî with this product, read the manual tor that equipment too.

. lf the equipment is used in a manner noî specified by the manufacturer, the protection provided by the

equipment may be impaired.

Notes on Handling the SYstem

1. Handle the product gentlY

This product is a precision optical insîrument. Handle the product gently, avoiding any physical shocks'

In particular, the optical system used on DIC method must be kept strain-free; handle the objective and

condenser carefully so that they are not deformed.

2. Dirty lenses

Do not lel dust, fingerprints, etc. get on the lenses. Dirt on the lenses, mirrors, etc. will adversely affect

the view of the image. tf any of the lenses gets dirty, clean it as described in Chapter 6, ' Care and

Maintenance."

* 3. Installation location

In order to avoid degraded performance and to prevent malfunctions, take the following rcquirements

into consideration when selecting a location to inslall the product:

. lnstall the product in a localion with little vibration.

. Avoid installing the product in a location exposed to direct sunlight.

. Avoid installing lhe product in a dusty location.

. Avoid installing the producî in a location subject to high temperatures (40"C or higheo or high humidity

(60% or higher). (Such conditions could allow mold or condensation to form on the lenses and filters.)

4. Specimens

Use slide glasses and cover glasses that are free of dirt, scratches, and distortion when preparing

soecimens.

5. About this DIC attachment

This Dlc attachment employs the "senarmont system,' in which the contrast of the Dlc image is varied

by the direction of the Polarizer.

The Dlc prisms ar" ro o" intt"tt"d nearthe obiective and the condens€r lens. This attachment requires

the correct combination of the objective, condénser lens and the DIC prisms. Read the following notes to

. choose the correct combination.

For condenser cassettes (Dlc prism fof condenser) of lhe '@r, "oM", 'oH" or "ooSS" marking' use

the following combinations.

DIC prisms for obiective :

Dlc prisms for obiective and objectives work in specific pairs. use the Dlc prism for objective Îhal

has the same name as lhe obiective.

Condenser casaettes (DlC prisms for condenser) :

The condenser cassetle to be used (the Dlc prism for condenser) is determined by the NA

(numerical aperture) of the obiective and the type of the condenser lens' (The NA of each

obiective is indicatéd on the decorative ring of the obiective')

For LwD condenser lgns

NA < 0.5 @ L (blac* lett€rs on whlle base)

0.5-NA<1.0 @ M (blad( letbrs on whlia base)

1.0 s NA o. H (Uack letbrs m whits bas€)

For dry type high NA condsnser lens

0.5<NA<1.0 @ M (Yvhite lstlars on gre€n base)

1.0 s NA 6H (whlte letters on gre€n bas€)

For ELWD condonser lcns

NA < 0.5 -L (whlte letters on red base)

For oit type high NA conden3er lena

1.0 s NA oH (blac* lettars on lrellon baso)

1.0 = NA - SS (black letters on ysllovi, base)

Zmark:

rne otc prism tor objective having the z mark (Dlc pfism for Plan Fluor 10x), and the Dlc

prism for condenser Àaving the I mark (LWD condenser oL) should be used in pairs.

(2) Combination lor Nl / N2 / NR tYPe

r* cono"nser cassettes lDlC prism lor condenser) ol the "N1', "N2', or "NR' marking, see Table A

onthe next page and select the oblective, DIC prism for obiective, and DIC prism for condenser

(condenser casgette) resP€ctively.

òtandard combinalions, high conirast combinations, and high resolution combinations are listed. Use

the appropriate combination.

For EiWó objeAives, only one type of condenser lens can be used. See also Table A on the next

page lor the ;ombinaiion ót eLWD objective, DIC prism for obiective, and DIC prism for condenser

(condenser cassette).

Notes on Handling the System

àl.x r

Etx*l

xIE

xf!

xÉ.

Ètc

ElF.È. 6E -.8

GÈ à ì

EIFIE E

<ffi

ZI IÉ o

al€ff xl=

lo xxxx

6tÈl-E E_b î

Nà ò.

zg :

É.

-I

x(r xfE

àE E'

Eg" a

(v x=l=

éIè x

>Ee

!g'"a

xfE

xCE

xfr

i€"9

z-e E

5€,9

zat

B''

l6la:: -= A

=EÉ

>Eî

!É'é

<ì

E.E

Qé =

è9"R

ì6R E

{ìtèÉ

dd(,d

Èeoi

-9 a:E

!-< 9Z

dd(,tr EE

-F

< 9:

xx;a

6Et:

caqE

EEÈX

[èo-<

É9 ;

ó8;X<

xr!.óx

E,-Eà9P

.-s 88e:

o=o

xo9

Féié

9;ó:

aE I I

àY; à

].<0-o-

s6 6

QS xo

5E699

EÈÉFE

FFèEF

E5-E.EE

-t!

élH

>Eî

À6 ú

;g-e

(.)

ìf6

UJ H-

òÒ

=il

IJJ

GontentS

lntroduction I

Notes on Handling the System

Names of Parts 7

Microscopy

Princ3ples of DIC MicroscoPy

AssemblY

TroublÉhooting Table

Care and llaintènance

Names of Parts

lf the system has not yet been assembled, refer to Chapter 4, ,,Assembly," first.

For details on the assembly and handling of the microscope, power supply, etc., refer to their respective

instruction manuals.

(The Nikon Inverted Microscope ECLIPSE Ti-E with the DIC anachment mounted is shown below. Some

components may not be included in the set that you purchased.)

T-P2 DIC oolariz€r

(Slide to lhe lelt to bing ths

polarizer inro th€ oplical

path.)

Systom condeng€r

T|-NDG sextupb DIC nosepisca

T|-ND6-E sèxtuplo motorizsd

DIC nosópisce

Tl- D6.PFS perfa€t focus with

motorlzed nosépl€ce

(Athch a DIC obj€ctive and a DtC

prism for objective h€re.)

(Attach the DIC condenser

cassotte hsre.)

ffh€ro qrq lwo iypss of turrets:

a manually oporat€d ong and

the TI-CT-E motoriz€d

cond6nser turret.)

DIC prilm lor

obirctlv€

Th€ prcduct can b€ us6d with any ot the following

lhros eDl-fr filter turrets:

. TI-FLC ept.ll fitter !.rret

. TI-FLC-E motoriz€d epi-f filter tunet

. TI-FLC-SFIO motorized eplf, fitter turet

Figure l-1

Push in ìo bring the anatyz€r

into optlcal path.

Vibration

direction lever

clamp scrow

(bottom)

I o,.oo,"*r"

T-N2 anaayz€f

Epl-ll tllter turrot

Ol-A Analfzer Block is attached in the

turret.)

Chapter i Names of parts

T-P2 DIC polarizer and sysfem condenser

Rotation

Dial scalo (5. intervats

Whit€ ind€x nark

When using a high NA condenser tens

Condensor ap€dure

lsvsr

Sllder lever

Dul-proof plat€

Flt"",J3î?H"là""'mF

rufrfi{ffi$F$""d.i{i

Polarizer

s€cton

Polarizer rotaiion lev€r

Condensor tJret

Condgnsor screw

lever

Ext€nsion ùJbe

Condonsgr slider

Condgns€r

Figure l{

Figure I -2

Slider damp screvi,

High NA condonser tens

Microscopy

Focus and cenler the condenser as described in the manual provided with the microscope, and if lhe

Tl-ND6-E sextuple motorized DIC nosepiece, Tl-CT-E motorized condenser lurret or TI-FLC-E

motorized epi-fl filter turret (or TI-FLC-E/HQ motorized epFfl filter turret) is being used, also refer to the

instruction manual supplied with the motorized units forTi series.

. Inserî the "A" (empty) cassette into the optical path. (ll using the condenser slider, remove the

condenser cassette, or move the slider so that there is nothing in the optical path.)

. Remove the polarizer, the analyzer, and the objective DIC prism from the optical path.

. When using a high NA condenser lens:

In order to focus the field ap€rture diaphragm image on the specimen surface, and in order to

avoid striking lhe specimen with the condenser lens. move the condenser lens slightly closer than

the subiect distance for each condenser lens, and then bring the specimen into focus while raising

the condenser lens. When using a oiFimmersion type condenser, also check page 9.

DIC microscopy requires that the specimen containers, slide glasses, cover glasses, etc., be largely

free of optical distortion. Therefore, a container that will place plastic in the optical path is not suitable

for DIC microscopy.

In addition, if a direction adiustment is made in the optical system beforehand, it will be possible to

observe the DIC image with the besî contrast. (See page 15.)

Move the DIC l ox obiective into the optical path and focus on the specimen. (Stopping down the

aperture diaphragm slighîly will improve îhe contrast of the specimen, making it easier to bring il into

focus.)

Turn the condenser turret and bring the adequate condenser cassene for the 10x obiective into the

optical path. (See page 3, Table A.)

til

Rotialion clamD scrgw

Figure 2-l

tr Loosen the rotation clamp screw of the polarizer and then

r, gently rotate the polarizer to change the image contrast.

. The highest contrast is obtained by adjusting the viewfield

background to sensitive gray and then bringing the GIF filter

inlo the optical path.

. Because contrasl is obtained in the shearing direction

(see Figure 2-2), adjust the orientation of the specimen until

conlrast is obtained in the desired direction.

Viblalion direction

ol analyzsr

ll 9o', Shearing direclion

llXou"

Vibration directton

ol polarizer

Figure 2-2

Table 2-l

1.gmm (including slid€ glass with a thickness of f .2mm)

Chapter 2 Microscopy

6Changing the magnification

Ex. 1: DIC LWD 60x NA 0.7 and @M

1 . Rotate the nosepiece to bring the DIC LWD 6Ox obiective into the optical path.

2. Because the NA of the Dtc LwD 6ox objective is 0.7, rotate the turet to bring the condenser

cassette labeted'DlC 0.5 - 1.0', into the optical path.

3. Adjust the contEst by rotating the polarizer.

When with ification

Focus on the specimen using a low-magnification ob,ective (1ox). with the specimen in focus, contirm that

(1) the field aperture diaphragm image is corecfly focused on th€ specimen sudace, and

(z) rne same tmage is corecfly centered in the viewfield.

lf eilher of these is not true, re-adiust. Once both are true, switch to the high-magnification obiective.

when observing a specimen with a high-rnagnif ication obiective, such as 6ox or 1oox, first correcfly focus on

the specimen, and then re-ad.iust the field aperture diaphiagm image on rhe speciren .urt""à. -Éy oorng

this, you can easiry re-focus on the specimen by focusing o-n the riÀrd aperture diapt ,"gm ir"é". '

Color contrast microscopy

Flgurc 2-3

1 . Rotate the nosepiece to bring the plan Apo 2Ox oblective into the optical path.

2. For. the standard and good balance view, bdng the "N2 Dry, condenser cassette into the optical

path' For the high contrast view, bring the "Nr Dry" condenser cassette into the optical pat'h. lsee

Table A on page O.)

3. Adjust the contrast by rotating the polarizer.

Remove the dust-proot plate from the DIC polarizer and insert

the lambda plate.

Rotate the polarizer until the background color changes to lhe

sensitive red-violet, a specimen with variations in itslef ractive

index or thickness will show interferenc€ colors corresponding

to the slope of the ì/ariations, producing the highest color

contrast.

To observe the imag€ with the correct color temperature, slide

the NCB filter into the optical path, and adiust the brightness

adiestment dial to match the lamp rating. Use the NDfitter to

adjust the brightness of the image.

Dtc

Chapter 2 Microscopy .f

ffi

NA 0.85, subiect distance: smm

Because the lens tip is cut at a 45' angle to the specimen, a wider work space can be attained.

When using the manipulator, rotate the lens rolaîion ring so that the cut surface of the lens faces the proper

oosition.

Use with Nikon-specified oil filling the space between the slide glass or cover glass and the lens'

Soread an amount of immersion oil approximately the size of the condenser lens tip on the side of the slide

gàss or cover glass that faces the condenser. Be careful nol to create air bubbles in the oil' The oil should

be about l mm thick.

Also apply a small amount of immersion oil on the tip of the oil-immersion objective.

After focusing the field aperture diaphragm image on the specimen surface, tighten the condenser refocusing

damo to mark the lower limiî for tho condenser. This prevents the tip of the condenser from hitting the

sDecimen and also fixes the field aperture diaphragm image.

Bemove lhe DIC polarizer, analyzer, and obiective DIC prism from the optical path before starting

microscopy. Because doing so will increase the brightness of the image, use ND filters or the brightness

adjestment dial to adjust the brightness.

NA 1.4, subiectdistan@

Inhaltsverzeichnis

Andere Nikon Kamerazubehör Handbücher

Nikon

Nikon AFS NIKKOR 80-400mm f/4.5-5.6G ED VR Bedienungsanleitung

Nikon

Nikon BG-N16 Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 24-70mm f/2.8 ED Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 300mm f/4E PF ED VR Bedienungsanleitung

Nikon

Nikon AF-S DX NIKKOR 35mm f/1.8G Bedienungsanleitung

Nikon

Nikon AF Micro-Nikkor 200mm f/4D IF-ED Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 500mm f/4E FL ED VR Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 35mm f/1.8G ED Bedienungsanleitung

Nikon

Nikon AF-S NIKKOR 24mm f/1.8G ED Bedienungsanleitung

Nikon

Nikon AF-S DX NIKKOR 18-300mm f/3.5-5.6G ED VR Bedienungsanleitung

Nikon

Nikon MC-20 Bedienungsanleitung

Nikon

Nikon Circular Polarizing Filter @... Bedienungsanleitung

Nikon

Nikon WR-R10 Bedienungsanleitung

Nikon

Nikon NIKKOR Z TELECONVERTER TC-1.4x Bedienungsanleitung

Nikon

Nikon SB-N10 Bedienungsanleitung

Nikon

Nikon WC-E63 Bedienungsanleitung

Nikon

Nikon SB-600 FSA03601 Betriebsanleitung

Nikon

Nikon MC-EU1 Bedienungsanleitung

Nikon

Nikon AF DX Fisheye-Nikkor ED 10.5mm f/2.8G Bedienungsanleitung

Nikon

Nikon LD-1000 Bedienungsanleitung

Nikon

Nikon HL-CP10 Bedienungsanleitung

Nikon

Nikon SB-300 Bedienungsanleitung

Nikon

Nikon HN-CP12 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung