Niles Remote Control Anywhere Kit Bedienungsanleitung

Remote Control

Anywhere!™Kit

INSTALLATION AND OPERATION GUIDE

BLENDING HIGH FIDELITY AND ARCHITECTURE

PRECAUTIONS

IMPORTANT INFORMATION

The Remote Control Anywhere Kit is designed to provide

years of troublefree operation. For your protection, please

read these instructions thoroughly before proceeding

with your installation. Keep this manual for future reference.

Carefully observe and comply with all warnings,

cautions and operating instructions described in this manual.

WARNING

To avoid injury, the following basic safety precautions

will enable you to successfully install and use your

Remote Control Anywhere Kit.

PRECAUTIONS

WARNINGS - To prevent possible injury, the following basic safety pre-

cautions should be observed in the installation and use of your Remote

Control Anywhere Kit.

1. Read through the entire manual - Before attempting any installation,

read this manual thoroughly and keep it for future reference.

2. Avoid contact with all high voltage electrical wiring and equipment!

3. Keep away from water and moisture - Never use or install electronic

products near water, ie., near a bathtub, sink, washing machine, in a wet

basement, near a swimming pool, or anywhere else the product may be

exposed to water or moisture.

4. Wall Adapter cord protection - Do not run the power cord where it may

be subject to wear or abuse. Do not allow anything to rest on or roll over

the power cord which may damage it.

6. Lightning - It is suggested that you remove the WallAdapter from the wall

if your system will not be used for long periods of time. Power surges due

to lightning strikes may damage your equipment.

7. Check your local building and electrical codes - There may be spe-

cific requirements regarding running low voltage in your area.

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 1 Placing the Connection Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Step 2 Connecting the Sensor Cable to the Connection Hub . . . . . . . . . . . . . . 6

Step 3 Connecting the Sensor Cable to the Wall-Mount Sensor . . . . . . . . . . . . 7

Step 4 Connecting the 12V DC Wall Adapter and MicroFlashers . . . . . . . . . . . 8

Step 5 Mounting a MicroFlasher to A/V Components . . . . . . . . . . . . . . . . . . . 9

Step 6 Mounting the Connection Hub . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Step 7 Finding the Right Spot to Install the Wall-Mount Sensor . . . . . . . . . . . 12

Step 8 Safety Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Step 9 Cutting the Hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Step 10 Installing the Mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Step 11 Running the Sensor Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Step 12 Installing the Wall-Mount Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Step 13 Reconnecting the Connection Hub . . . . . . . . . . . . . . . . . . . . . . . . . 18

System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Running Sensor Cable in New Construction . . . . . . . . . . . . 22

Scheduling and Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Safety First! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Drilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Pulling the Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Concealing Sensor Cable in Existing Walls . . . . . . . . . . . . . . 23

The Remote Control

Anywhere! Kit enables you

to operate your remote

controlled audio/video

equipment from virtually any

location. Now you can place

your audio/video (A/V)

components out of sight

(behind cabinet doors, in the

rear of a room, or in a

different room) and still

conveniently control your

system.

Kit Contents

Check that your Remote

Control Anywhere! Kit

contains the following:

• Connection Hub

• Wall-Mount Sensor

• 12V DC Wall-Adapter

• Mounting Bracket

• MicroFlashers (3)

• Sensor Cable (100ft)

Tools Needed

• pencil

• drywall saw

• standard screwdriver

• phillips screwdriver

• wire strippers

• drill (and assorted bits)

• wire coat hanger

INTRODUCTION

Connection

Hub Wall-Mount

Sensor

Mounting

Bracket

MicroFlashers (3) Sensor Cable

(100ft)

12V DC

Wall Adapter

GETTING STARTED

While the Remote Control

Anywhere! Kit is compatible

with most brands of

audio/video components,

there are a few exceptions.

You should perform a

temporary hook-up to test

for compatibility before you

conceal wire or permanently

mount any parts.

Steps One through Five

describe how to perform a

quick and easy check for

compatibility.

Once you have determined

that all of your remote

controlled A/V components

are compatible, proceed

with the rest of the

installation.

Step 1

Placing the

Connection Hub

Place the Connection Hub so

that the MicroFlasher wires

will reach the components.

Never place the

Connection Hub closer

than 1 foot away from a

television set. (See Figure 1)

Step 2

Connecting the

Sensor Cable to the

Connection Hub

For your convenience, the

Sensor Cable ends have

been stripped. Insert one of

the stripped ends into the

INPUT connector on the

Connection Hub as shown

in Figure 2 and

tighten the screws.

The Cable must be con-

nected as follows:

1 = Red

2 = Bare

3 = Black

INSTALLATION

Additional Sensors

REMOTE CONTROL ANYWHERE! KIT

CONNECTION HUB

123

Red

Bare Black

Figure 1

Figure 2

Make sure that the

stripped ends of the wire

do not come in contact

with one another or any

surface other than the

connector.

Step 3

Connecting the

Sensor Cable to the

Wall-Mount Sensor

Pull out the removable

connector from the back of

the Wall-Mount Sensor.

Insert the other stripped end

of the Sensor Cable into the

removable connector on the

Wall-Mount Sensor and

tighten the screws.

(See Figure 3)

The cable must be

connected as follows:

1 = Red

2 = Bare

3 = Black

Plug the connector into the

connector socket on the

back of the Wall-Mount

Sensor. Make sure that the

orientation of the connector

is correct. (See Figure 4)

INSTALLATION CONTINUED

123

Red

Bare

Black

Figure 3

Figure 4

Step 4

Connecting the

12V DC Wall-

Adapter and

MicroFlashers

Plug the connector on the

supplied 12V DC Wall-

Adapter into the socket

labeled POWER on the

Connection Hub and then

plug the wall adapter into

a live electrical outlet. The

power LED should light.

If the LED does not light,

confirm that the outlet

you used is live by plug-

ging in a lamp.

Plug the MicroFlashers

into any of the sockets

labeled FLASHER OUT-

PUTS on the Connection

Hub. (See Figure 5)

INSTALLATION CONTINUED

Additional

Flashers

REMOTE CONTROL ANYWHERE! KIT

CONNECTION HUB

Figure 5

Step 5

Mounting a

MicroFlasher to A/V

Components

Make sure all of your remote

controls have batteries and

that they are able to operate

the A/V components.

Locate a place for the

remote control that is within

arm’s length of the A/V

components, yet cannot

directly control them. Place

the Wall-Mount Sensor no

closer than two feet in front

of the remote control.

(See Figure 6)

Hold the MicroFlasher four

inches in front of the remote

sensor window on the A/V

component’s front panel.

Press buttons on the remote

control while watching the

front panel of the A/V com-

ponent. When the compo-

nent responds repeatedly to

the commands, peel off the

protective backing on the

MicroFlasher and place the

MicroFlasher in that location.

continued

INSTALLATION CONTINUED

Figure 6

Andere Handbücher für Remote Control Anywhere Kit

Inhaltsverzeichnis

Andere Niles Fernbedienung Handbücher

Niles

Niles TVC-1 Original Betriebsanleitung

Niles

Niles R-6L Original Betriebsanleitung

Niles

Niles RCA-HT2 Bedienungsanleitung

Niles

Niles RCA-HT2 Bedienungsanleitung

Niles

Niles RCA2 Original Betriebsanleitung

Niles

Niles INTELLIPAD CI Bedienungsanleitung

Niles

Niles RCA3 Bedienungsanleitung

Niles

Niles VCS-2S Bedienungsanleitung

Niles

Niles iREMOTE TS Bedienungsanleitung

Niles

Niles MVC100IR Original Betriebsanleitung

Niles

Niles R-6L Bedienungsanleitung

Niles

Niles EVC-100 Bedienungsanleitung

Niles

Niles iREMOTE TS Bedienungsanleitung

Niles

Niles VCS50R Fehlerbehebungshandbuch

Niles

Niles RCA-TT Bedienungsanleitung

Niles

Niles RCA-TT Bedienungsanleitung

Niles

Niles REMOTE CONTROL ANYWHERE! RCA-TT2 Bedienungsanleitung

Niles

Niles RCA-HT Bedienungsanleitung

Niles

Niles HR200 Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

Niles

Niles SVC100R Original Betriebsanleitung

Niles

Niles RCA-SM Bedienungsanleitung

Niles

Niles VCS100 Original Betriebsanleitung

Niles

Niles VCS-2D Original Betriebsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung

Invacare

Invacare G91S Bedienungsanleitung