Nissin MG80 Pro Bedienungsanleitung

Canon / Nikon / Sony

Fujifilm / Panasonic / Olympus

INSTRUCTION MANUAL

Thank you for purchasing a Nissin product

Before using this flash unit, please read this instruction manual and

refer to the manual of camera owner carefully to get a better

understanding of the proper operation to enjoy flash photography.

The flash Nissin MG80 Pro (Canon / Nikon / Sony/ Fujifilm / Panasonic /

Olympus) is an advanced commander built-in flash for wireless flash shooting.It

controls up to 8 groups of NAS (Nissin Air System) flash that have a wireless

multiple flash shooting function using NAS (radio transmission). Please note

that Nissin MG80 Pro is not usable with other branded cameras for TTL

operation.

Please refer to Nissin’s compatibility chart shown here:

http://www.nissindigital.com/compatibility-chart

Compatible cameras

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Nissin Air System (NAS) is a Nissin wirelessly remote control flash light system,

and the Nissin wireless flash (NAS flash) and Nissin radio receiver (NAS receiver)

as remote slave units.

The signal of MG80 Pro is transmitted by using 2.4 GHz transmission.

Insert MG80 Pro on the camera hot shoe as a NAS commander.

Transmission distance is approx. 100m (330 ft.)

(Metal/ Wire/ Wall/ another 2.4 GHz radio frequency may cause a

reduction in the NAS transmission distance)

These safety instructions refer to important information on how to use this product safely

and properly. Please read the following instructions before using the product.

SAFETY INSTRUCTIONS

Do not touch the inside parts from the opening when the unit was dropped or broken.

Place the batteries correctly in position. Placing the batteries in wrong polarity may

cause leakage, exothermic heat or explosion.

CAUTIONS

Do not leave or store the commander unit in the temperature over 40ºC/ 104ºF, such as

in the automobile.

The commander unit is not water resistance. Keep the unit away from rain, snow and

humidity.

Do not use benzene, thinner or other alcoholic agents to clean the unit.

Do not use this commander unit with cameras which are not recommended in the

compatibility list at official website, otherwise it may damage the camera’s circuitry(*).

Remove the batteries when not in use for a longer period of time.

Do not use the Nissin MG80 Pro to pick up whole camera system when it installed on

your camera. To pick up the whole camera system, you should hold the handle of

camera body or the lens..

This sign refers to conditions which may cause damage or defect.

（*）Please refer Nissin’s compatibility chart shown here:

http://www.nissindigital.com/download.html

Names of the Components

Group selection button

Group on/off button

Modeling light button

(Basic/Advanced Groups button)

M/TTL Mode Button

(OPEN Mode button)

LCD panel

Select dial with buttons

Channel button

HSS button

Buzzer button

M.Zoom button

Panel Lock/Unlock button (hold 1sec.)

(1) The AF-assist lamp supports digital system cameras measuring autofocus in the center of the image field only.

It does not support other camera brands, other types of Canon, Nikon, Sony, Fujifilm, Panasonic and Olympus

cameras or camera models without our compatibility test.

(2) The shutter cable socket desinged for wireless remote shutter function on MG10 and MG8 only, the socket

cannot be use to trigger the flash. For more information, please refer to MG10 and MG8 instruction manual.

Pilot button (Test flash button)

Power On/Off button

Lock ring

Modelling Light

Micro SD card slot

(for firmware update)

Shutter cable socket (2.5mm) (2)

AF-assist light

(1)

Bounce lock

Battery compartment door

Hotshoe contacts

Inserting batteries

Energy saving

Battery status

1. Open the battery compartment door and insert 4 x 14500

Li-ion or size AA rechargeable batteries as shown in the

picture.

2. Make sure the + and - battery contacts are correctly

inserted in the battery compartment.

3. Close the battery compartment door and slide it back in

place.

Before starting wireless flash shooting.

Press any button Press Power button

Dim

30 sec

Sleep

2 mins

Turn Off

60 mins

A blinking signal shown on the Pilot Button mean:

- Wrong insertion of battery (battery type and/or position)

- Low battery

- Battery overheating

It is recommended to use 4 batteries in the same brand and type, and replace them all at

the same time.

Press power on to activate Nissin MG80 Pro,

hold the Power button for 7 seconds to reset to factory default setting

Default setting:

1. Mode: On-Camera

2. TTL mode: +/- 0EV

3. M Manual mode: 1/256

4. Zoom setting: Auto

5. HSS mode: off

6. Buzzer: on

Default Setting Reset

Basic Operation

NOTE

Do not use the MG80 Pro as a holder to pick up the whole camera system.

Mounting MG80 Pro on the camera

Removing MG80 Pro from the camera

Turn off MG80 Pro.

Turn the lock ring of MG80 to loosen it all the

way as shown in the picture.

Slide the mounting foot of MG80 into the

hotshoe of the camera.

Turn the lock ring to opposite direction and

tighten it.

Turn the lock ring of MG80 to loosen it

all the way as shown in the picture.

Slide the mounting foot of MG80 out of the

hotshoe of the camera.

Menu Screen For Main Modes

MG80 Pro Flash Mode and Functions

On-Camera Mode

Flash light automatically controlled by the

camera with the flash exposure or selecting the

desired manual power on the flash unit.

Commander Mode

Placing multiple flashes (slave flash) off camera

and controlling the lighting operation.

Slave Mode

Synchronizes to the wireless remote flash system.

The MG80 Pro can be use in 3 mode:

- On-Camera Mode

- Commander Mode

- Slave Mode

To change the mode in MG80 Pro,

switch on MG80 Pro, press the

3 seconds to select a mode.

On-Camera Mode

TTL flash power compensation

With the latest TTL flash control system, the flash power level is always

automatically controlled by the camera for the most appropriate exposure.

You can soften or weaken the light, or give more to the subject without

changing the environment or background exposure effect. MG80 Pro can

make it possible to adjust exposure quickly for each particular flash picture

as needed.

1. Set MG80 Pro to the camera’s hotshoe and press to switch on.

2. Press the 3 seconds to select “On-Camera” Mode.

3. Press the button to choose “TTL” mode.

4. Rotate the dial to select the power compensation.

5. TTL flash power compensation provided starts from -2EV to +2EV (12 steps) and

controlled by 1/3 EV step internal.

Take a picture and the subject is shown with required lighting effect by keeping the

background exposure level as originally expected.

NOTE

On some cameras, this setting is provided in its menu. When you set the TTL flash

power compensation on camera it is also set on the MG80 Pro will be counted in

addition to the compensation you selected in the camera’s menu mode. ( i.e. set +1

compensation on the flash and set +1.3 compensation on the camera it will

generate +2.3 EV in total.)

Red color bar represent 1 step, White color bar represent 1/3 step.

Andere Handbücher für MG80 Pro

Inhaltsverzeichnis

Andere Nissin Kamerablitz Handbücher

Nissin

Nissin Di866 Bedienungsanleitung

Nissin

Nissin Speedlite Di622 Handbuch

Nissin

Nissin I60A Bedienungsanleitung

Nissin

Nissin Di866 Bedienungsanleitung

Nissin

Nissin Speedlite Di466 Bedienungsanleitung

Nissin

Nissin MG80 Pro Bedienungsanleitung

Nissin

Nissin NDMG10 Bedienungsanleitung

Nissin

Nissin Di700 Bedienungsanleitung

Nissin

Nissin MG10 Bedienungsanleitung

Nissin

Nissin Speedlite Di466 Bedienungsanleitung

Nissin

Nissin Di700A Installationsanleitung

Nissin

Nissin Speedlite Di466 Bedienungsanleitung

Nissin

Nissin Di700 Montageanleitung

Nissin

Nissin MG8000 Extreme Bedienungsanleitung

Nissin

Nissin MARK II DI622 Bedienungsanleitung

Nissin

Nissin i40 Installationsanleitung

Nissin

Nissin Mark II Di866 Pofessional Bedienungs- und Wartungshandbuch

Nissin

Nissin Di866 Bedienungsanleitung

Nissin

Nissin Mark II Di866 Pofessional Bedienungsanleitung

Nissin

Nissin Di700A Bedienungsanleitung

Nissin

Nissin Mark II Di866 Pofessional Bedienungsanleitung

Nissin

Nissin Di700A Bedienungsanleitung

Nissin

Nissin MG8000 Extreme Bedienungsanleitung

Nissin

Nissin MF18 Bedienungsanleitung

Beliebte Kamerablitz Handbücher anderer Marken

Canon

Canon 5246B002 Bedienungsanleitung

Sigma

Sigma EF-610 DG SUPER - Bedienungsanleitung

Godox

Godox DP300 Bedienungsanleitung

Sony

Sony HVL-FDH4 Bedienungsanleitung

Sony

Sony HVL-RLA Bedienungsanleitung

Nikon

Nikon SB-28 Bedienungsanleitung

Olympus

Olympus FL 36R Bedienungsanleitung

Nikon

Nikon BC-7 Bedienungsanleitung

Nikon

Nikon SB-800 Bedienungsanleitung

DÖRR

DÖRR DFX-300 Bedienungsanleitung

Altura Photo

Altura Photo AP-305N Bedienungsanleitung

Canon

Canon SPEEDLITE 300EZ Bedienungsanleitung

Sunpak

Sunpak 622 Super Pro-System Bedienungsanleitung

Polaroid

Polaroid PL108-AF Bedienungsanleitung

Pentax

Pentax AF240Z Bedienungsanleitung

Pixapro

Pixapro Li-ion 350 II N Bedienungsanleitung

Canon

Canon 430EX - Speedlite II - Hot-shoe clip-on... Bedienungsanleitung

Godox

Godox Thinklite TT350P Bedienungsanleitung