NJD Electronics IQ-MX80 Bedienungsanleitung

Features of the IQ-MX80

• Controls up to 16 NJD intelligent lighting

products independently.

• Controls: Predator MX and HX,

Chroma HX and Chroma 50,

Microbeam 100,

IQ250 (Mk.1, 2 & 3) ,

IQ500 (Mk.1 & 2),

Datamoon,

Spectre,

Raptor,

Quasar,

and SB500 Super Blitzer

• Joystick for manual operation or programming

• Touch pad control of colour and gobo.

• Ten built in programs

• Ten user-writable programs of 250 steps

• Real-time programming

• Strobe facility

• Lamp on/off facility (halogen lamps only)

IQ-MX80

IMPORTANT

Installer and Users please note:

These instructions should be read carefully and left

with the user of the product for future reference.

Installation.

Connect the IQ-MX80 to the 230V mains supply with the lead

supplied.

• Brown = live • Blue = neutral • Green/Yellow = earth

• The IQ-MX80 must be earthed to ensure safety and

correct operation of the touch pads.

If sound activated operation is required, connect a sound

signal, either 0dBm from the line-level output of a mixer, or the

speaker output from an amplifier, to the sound input jack.

Great care should be taken not to connect the sound input to

the DMX-output socket, as this may destroy the internal

electronics (the DMX line-driver)

Connect the DMX output from the IQ-MX80 to the DMX input

of the nearest lantern. The DMX output socket is a 3-pin XLR. Pin

connections are as follows:

Pin 1 = ground connect to sleeve on stereo ¼" jack

or Pin 1 on 5-pin XLR

Pin 2 = Data + connect to tip on stereo ¼" jack

or Pin 3 on 5-pin XLR

Pin 3 = Data − connect to ring on stereo ¼" jack

or Pin 2 on 5-pin XLR

On a 3-pin XLR, Pin 3 is the one in the middle.

Refer to the “externally controlled” section of the lantern user

guide for further information on connection.

Portable Appliance Testing

The IQ-MX80 should be checked for Electrical Safety annually,

and if it is hire equipment, before it is hired out. A high-voltage

test (at 500V or 1000V) should be carried out between live and

earth, and an earth bonding test between the case and the earth

connection (at 6A or 10A). Insulation resistance should be

greater than 10MWand earth bonding resistance less than

0.5W. A high voltage test may also be carried out between the

User Guide IQ-MX80

DMX and audio inputs and live, if the equipment has passed the

live-earth test.

Do not test high-voltage or earth bonding between DMX or

audio inputs and earth - this will destroy the electronics.

Setting the DMX address switches.

The DMX switches on the lantern should be set as shown.

If your lantern has a 3-digit LED display, set the display to the

number in the "DMX start address" column, and set the operating

mode to "F 1" or "F 3" (F 3 reverses the left-right joystick

movement. This allows the joystick to work in the most logical

fashion, depending on whether the lanterns are facing towards or

away from the controller).

If it has DIL switches, refer to the "switches ON" column. If

there are also switches labelled "MODE" (e.g. Spectre) set them

to the "IQ-MX80" setting

Note: The switch numbers refer to the numbers printed on

the product label adjacent to the switch, not to the numbers on

the switch itself.

Lantern number DMX Switches ON

start address (other switches off)

1 1 None

2 9 8

3 17 16

4 25 16, 8

5 33 32

6 41 32, 8

7 49 32, 16

8 57 32, 16, 8

9 65 64

10 73 64, 8

11 81 64, 16

12 89 64, 16, 8

13 97 64, 32

. . .continued overleaf

User Guide IQ-MX80

Lantern number DMX Switches ON

start address (other switches off)

14 105 64, 32, 8

15 113 64, 32, 16

16 121 64, 32, 16, 8

1 (reversed in X direction) 5 4

2(reversed in X direction) 13 8, 4

3 (reversed in X direction) 21 16, 4

4 (reversed in X direction) 29 16, 8, 4

5(reversed in X direction) 37 32, 4

6(reversed in X direction) 45 32, 8, 4

7(reversed in X direction) 53 32, 16, 4

8 (reversed in X direction) 61 32, 16, 8, 4

9(reversed in X direction) 69 64, 4

10 (reversed in X direction) 77 64, 8, 4

11 (reversed in X direction) 85 64, 16, 4

12 (reversed in X direction) 93 64, 16, 8, 4

13 (reversed in X direction) 101 64, 32, 4

14 (reversed in X direction) 109 64, 32, 8, 4

15 (reversed in X direction) 117 64, 32, 16, 4

16 (reversed in X direction) 125 64, 32, 16, 8, 4

If the lantern has switches labelled "1", "2" or "128", set

these to OFF. Switch 4 reverses the X-direction movement. This

allows the joystick to work in the most logical fashion, depending

on whether the lanterns are facing towards or away from the

controller. Predators and later IQ250/IQ500 have an extra x-

reverse switch. For these lanterns set the "4" switch to OFF.

The IQ-MX80 only outputs the first 128 DMX channels. A

lantern with its DMX address set to a number greater than 128

will not function.

Up to 32 lanterns may be connected to the IQ-MX80.

Lanterns assigned to the same channel will perform identically.

The total length of DMX cable run should not exceed 250m

User Guide IQ-MX80

Operation.

When the IQ-MX80 is first turned on from new, it will start in

Manual mode, the display will show - - - - - and the manual LED

will be lit. On subsequent occasions, when the IQ-MX80 is

switched on, it will resume operation from where it was switched

off, allowing it to be turned on and off remotely and operate

automatically in situations where an operator is not available.

Manual Mode

In manual mode, the user has direct control over any number

of the lanterns with the colour and gobo touch pads and the

joystick.

First select the colour and gobo required. To select split

colours, touch two adjacent pads: i.e. to select red/green split,

touch red and green together. To select colour scrolling, set the

scrolling speed on the speed control and then touch magenta and

white together.

Then select the lanterns required by touching the lantern

select pads. The selected colour and gobo will then be assigned to

the selected lanterns. The joystick will then control the movement

of the selected lanterns. The colour and gobo must be selected

first. This allows several cans to be controlled simultaneously by

the joystick, but with different colours and gobos.

Whenever a lantern is selected it takes the colour and gobo

selected on the colour/gobo keypad. The joystick controls the

movement of all selected lanterns.

To change the colour and gobo, change the colour and gobo,

deselect the lantern by touching the lantern select pad, and then

re-select the lantern.

When a lantern is de-selected, it remains in the last position

set on the joystick. This allows all lanterns to be positioned

individually.

To select strobe touch blackout and ltogether. If selecting

strobe on the Microbeam, Datamoon or IQ250, first select white;

otherwise these products will attempt to strobe in other colours

and will not be too successful. The Predators, Chroma HX and

IQ500 can strobe in any colour.

In manual mode, the blackout pad turns the lamp off on

User Guide IQ-MX80

products with halogen lamps; on products with Metal Halide

lamps, the lamp continues to run and is blacked out by a shutter.

Short-cut: to change the colour and gobo of all selected

lanterns, select the new colour and gobo and touch the run pad.

Use with various lanterns

• Predator HX/MX

all features are available

• IQ500

Split colours and colour scrolling are not available

• Microbeam, IQ250

Gobo pads have no effect (except for blackout and strobe)

• Datamoon.

Joystick x-axis controls dish rotation, y-axis has no effect. Split

colours and colour scrolling are not available. Gobo pads have no

effect (except for blackout and strobe)

• Chroma HX / Chroma 50

Joystick x-axis has no effect, y-axis controls dimming. Some

split colours and colour scrolling are available, but gobo pads have

no effect (except blackout and strobe)

The IQ-MX80 is not compatible with the Chroma 250.

• Raptor

Joystick x-axis controls barrel rotation, y-axis controls barrel

left-right movement. Split colours are available.

• Quasar

Joystick x-axis controls dish rotation, y-axis controls dish left-

right movement. Split colours are available.

• SB500 Super Blitzer

Joystick x-axis controls dish rotation, y-axis controls dimming.

Colours and gobos have no effect (except blackout and strobe)

Running programs.

Switch off manual mode by touching the MAN. pad.

The display will now show the program number and the step

number in the program. Select the program number by touching

the PROG pad. Programs 1 to 10 are factory written programs

and cannot be overwritten. Programs 11 to 20 are user-writable

programs, and can be overwritten at any time if the write enable

User Guide IQ-MX80

switch on the rear panel is in the "enable" position. A battery

inside the IQ-MX80 retains the user programs when the mains

power is disconnected, provided that the IQ-MX80 is used at least

once every 3 months.

Select the animation mode by touching the SOUND pad.

Green =sound animated

No led lit = variable speed animation - the speed is set on the

speed control

Red = stop/single step operation.

The lanterns will remain static, and will advance one step

when the STEP pad is touched.

When the IQ-MX80 reaches the end of the program it starts

again at the beginning. To run through all programs sequentially,

select run mode by touching the RUN pad. The run led will light.

The IQ-MX80 will run through each program four times and then

change to the next.

To return to manual mode, touch the MAN. pad. The IQ-

MX80 will return to the lanterns and the colours that were

selected when manual mode was exited.

Short-cut:

To change programs quickly, touch the PROG pad and

touch the lantern select pad that corresponds to the number of

the program required before releasing the PROG pad. Only

programs 1 to 16 are available by this method.

Manual Override:

Whilst running programs, the lantern select and colour/gobo

pads can be used as in manual mode, to override the program.

The only difference is the scroll speed which is fixed. When the

lantern is de-selected it resumes running the program.

To remove certain lanterns from a program, select

BLACKOUT and select the lanterns to be removed.

Writing programs.

Programs 11 to 20 can be written by the user.

The write enable/disable switch on the rear panel must be in

the enable position.

Select write by touching the WRITE pad, the write LED will

flash. Select the required program by touching the prog pad, until

User Guide IQ-MX80

the required program number appears in the display.

Set up the required colours, gobos and beam positions on the

lanterns for the first step of the program and touch ENTER.

The letter Eappears in the step display to acknowledge that enter

has been touched. Touch STEP to advance to the next step in

the program. The lanterns will then display the settings previously

stored in the new step. To view the current settings of the joystick

and colour/gobo pads, touch RUN.

Repeat for the other steps in the program, up to a maximum

of 250 steps.

If programming fewer then 250 steps; after the last step,

Select lantern #1, touch STEP to advance to the next step, and

then touch END. The letter Eappears in the program display to

acknowledge that end has been programmed.

It is most effective to program each lantern in turn. When

programming, lanterns that are not selected will display the

colours and positions that have already been programmed into

them.

Touch the WRITE pad again to exit from program-write

mode. Switch the write disable switch back into the disable

position to protect the programs that had been written.

When writing or running programs, the BLACKOUT pad

operates the shutter leaving the lamp on.

Real time programming.

The write enable/disable switch on the rear panel must be in

the enable position.

Select write by touching the WRITE pad, the write LED will

flash. Select the required program by touching the PROG pad,

until the required program number appears in the display.

If the program is not to involve all 16 lanterns, first clear the

program as follows: Select BLACKOUT and all 16 lanterns.

Set the joystick to the centre. Then touch START and wait until

the display counts to 250.

Set the colours and gobos and select the lanterns required.

Move the beams to the starting position using the joystick. When

ready, touch the START pad. The IQ-MX80 will record the

joystick position ten times per second, making a program of 250

User Guide IQ-MX80

steps which is 25 seconds long. If the program needs to be

shorter, touch the END pad.

To change colours and gobos, select the new combination,

deselect then reselect the lantern by pressing the lantern select

pad twice; or, to change the colour and gobo of all selected

lanterns, touch the RUN pad.

Real time programs can be built up one lantern at a time, or

in groups, until all 16 channels are involved, by repeating the

programming process, selecting different lanterns. When

programming, the lanterns that are not selected, will display the

patterns that have already been written, allowing movement of

lanterns to be synchronized.

Editing programs

The write enable/disable switch on the rear panel must be in

the enable position.

Select the program to be edited using the PROG pad. Select

the step to be edited using the step pad. Set the colours and

gobos and select the lanterns to be edited. Move the beams to

the required position using the joystick and touch ENTER.

Extending programs.

Select the program to be edited using the PROG pad.

Using the STEP pad, select the step after the last step in the

existing program. Continue programming as above until the last

step of the new program is reached, and touch step to advance

to the next step, then select Lantern #1 and touch END.

Programs must be extended one step at a time, it is not possible

to extend programs using the real-time programming technique.

Shortening programs.

Select the program to be edited using the PROG pad. Using

the step pad, select the step which is one more than the last step

of the edited program and touch END.

Notes on DMX.

The DMX system is a high-speed digital data system, which

can transmit all the information required for light dimmers, multi-

motor lighting effects etc. down a single cable.

Each unit connected to the DMX signal is given an address,

and it compares this to the data being sent on the DMX cable, so

User Guide IQ-MX80

it can determine which data is addressed to it. It then uses this

data to move a motor or set a brightness level as required by the

controller.

As the DMX system can transmit as much information as

512 analogue control wires down a single cable, it has to

transmit very quickly, in fact, at a frequency 12 times higher than

the highest audio frequency. Anyone who has used long leads for

audio will realise that it is difficult to do without losing the higher

frequencies.

To make the DMX system work at such high frequencies, it

requires special circuitry and special cable. Cable can be designed

to pass high frequencies with no loss if it has the correct

resistance connected at each end, this resistance is called the

characteristic impedance of the cable. DMX cable has a

characteristic impedance of 120W.

All NJD DMX products with ¼" jacks are designed to ensure

that the resistors are connected automatically. Without them, the

signal reflects off the end of the cable and interferes with the new

data coming the other way. If the cable is not correct, the system

will not work. Products with XLRs require a DMX terminator to be

fitted to the DMXout connector of the last lantern in the chain -

refer to the lantern user guide.

Most good quality low-capacitance screened twisted pair

cables will work, but twin individually screened will not. Also, if the

cable is split or joined other than end-to end, the system will stop

working.

Fault Finding

• Lanterns do not operate

Break in DMX cable between controller and first lantern.

DMX Cable shorted out*

DIL switch #128 turned on (should be off)

• Only certain lanterns operate

break in DMX cable*

DIL switch #128 turned on (should be off)

• Lanterns operate erratically

Unterminated cable in output socket of last lantern.

poor or intermittant DMX earth connection*

User Guide IQ-MX80

Inhaltsverzeichnis

Andere NJD Electronics DJ-Equipment Handbücher

NJD Electronics

NJD Electronics NJ164 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung