No problaim SQUARE Benutzerhandbuch

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

PNEU ZELT SQUARE

SETUP MANUAL

Sky Dancer | Sky Ads, Helium | Spiele, Fun Action Games | The Others

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

GENERAL SCHEME

inﬂaon valves

overpressure valves

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

INFLATION

Clean an area, where the tent should be placed. Mainly sharp objects and chemicals have to be

removed. Use of protecon blanket is recommended.

Remove tent from the bag, place it to its one

of possible posions.

Check posion and funcon of all 16 valves.

A base part of black valve must be properly

ghted (check a valve seal before use), small

black cap must stay open. Red overpressure

valves must be installed on other 8

posions, well ghted to prevent air leak. In

a case tent was not used for longer me

period, it is recommended to check

funconing of all overpressure valves by

pushing the spring with a ﬁnger or blowing

through the valve. Paralelly, seats of all

valves shall be checked to avoid sand grains

or dirt to block closing the valve.

3. red overpressure

valves

black inﬂatable

valves

black arrow

posion

Check correct placement of small roof over

the central assembly. Inate three legs (left,

right and a top one) by connect a hose of

pump to the black valve and start ination,

ideally till the moment when overpressure

valve would open automatically.

Overpressure valves are calibrated to the

maximum allowable pressure, do not

overpressure your tent more as necessary.

Do not disable overpressure valves, it may

cause a bladder rupture!

SQUARE SETUP MANUAL

1st

2nd

3rd

hose of pump

Clean an area, where the tent should be placed. Mainly sharp objects and chemicals have to be

removed. Use of protecon blanket is recommended.

Remove tent from the bag, place it to its one

of possible posions.

Check posion and funcon of all 16 valves.

A base part of black valve must be properly

ghted (check a valve seal before use), small

black cap must stay open. Red overpressure

valves must be installed on other 8

posions, well ghted to prevent air leak. In

a case tent was not used for longer me

period, it is recommended to check

funconing of all overpressure valves by

pushing the spring with a ﬁnger or blowing

through the valve. Paralelly, seats of all

valves shall be checked to avoid sand grains

or dirt to block closing the valve.

3. red overpressure

valves

black inﬂatable

valves

black arrow

posion

Check correct placement of small roof over

the central assembly. Inate three legs (left,

right and a top one) by connect a hose of

pump to the black valve and start ination,

ideally till the moment when overpressure

valve would open automatically.

Overpressure valves are calibrated to the

maximum allowable pressure, do not

overpressure your tent more as necessary.

Do not disable overpressure valves, it may

cause a bladder rupture!

SQUARE SETUP MANUAL

1st

2nd

3rd

hose of pump

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

Inﬂate fourth leg. Once the leg gets

pressure, help the whole tent to erect and

put it to the future posion.

Inﬂate all 4 horizontal beams to tension the

structure.

After releasing an ination hose, do not forget

to close and tight the small cap of each

ination valve.

Side walls and visors can be zipped on the tent all the time, but we rather suggest to install it to already

inated tent. Each wall or visor ts to each side of the tent. An artwork side of the wall may be faced to

outside or inside of the tent.

Check span of legs before

zipping the wall on the roof.

Span of legs bigger as width

of side wall can cause

damage of zipper during

zipping on the wall. Try to

minimaze a stress of zipper

by fair handling. Secure end

of zipper with velcro after

zipping on the side wall.

SQUARE SETUP MANUAL

ROOF

WALL

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

DEFLATION

Zip oﬀ all side walls and visors, pack each separately.

Open inﬂaon valves on all 4 horizontal

beams.

Open ination valve on one leg. Once some

air is released and internal pressure in the leg

decrease, pull leg to the transverce one. After

whole tent will lay down, open ination valves

on rest 3 legs.

SQUARE SETUP MANUAL

Once, most of air is released, put legs to the

paralell order.

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

Rolling the tent in a direcon from small

roof towards to valves. In this way you will

release the rest of air out of the structure.

Unroll it and roll again to get a compact

package, ﬁng into the trolley bag. A last

step before pung the package into the

bag is to screw all valves back into their

posion.

Steel spikes must be packed in an extra pouch, which is included in a delivery.Put a pouch into separate

pocket in a trolley bag.

Put spare parts and a repair kit into another separate pocket in a trolley bag. When all parts including side

walls etc are in a trolley bag, zip it on smoothly. If the volume is too big, use support tapes with trident

buckles to bing the bag, decrease a volume and help the zipper to prevent its damage.

SQUARE SETUP MANUAL

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

ANCHORING

SCHEME

SQUARE SETUP MANUAL

ANCHORING

SCHEME

anchoring in a calm wind

anchoring in a strong wind

anchoring on hard surface

SQUARE SETUP MANUAL

ANCHORING

SCHEME

anchoring in a calm wind

anchoring in a strong wind

anchoring on hard surface

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

Anchor each leg by using four steel spikes

(point C) through aluminium buckles in 45°

to the ground. Check right position of legs to

avoid stress on zippers or weaved side

walls. In a case of strong wind it is

recommended to anchor wall base with steel

spikes through eyelets too.

There are main ropes attached to points A

directly from the factory. Those ropes must

be anchored with steel spikes. An optimum

angle of spikes to the ground is 45°, an

optimum angle of ropes to the tent can see in

anchoring schema.

Push triangular plastic cleats towards to the

roof to tighten all ropes.

ANCHORING TO THE STRONG WIND : Repeat a procedure of basic anchoring, just add four more ropes to be

attached by quick links to points B. Additional ropes are included in a package.

Adjust an additional rope length in a way, that it is 5-10cm shorter as a distance between point B and D.

Once adjusted, hitch the loop on the spike of point E. As the rope is shorter, it is well tensioned to help a tent

to resist a strong wind.

ANCHORING ON HARD SURFACE (TO THE LIGHT WIND / by using ballast bags) Fill ballast bags with water

through dismounted valve. After water  lling screw the valve including top cap to avoid water

leak.Warning: Ballast bag is designed for pouring water, not to be pressurized with hose! Do not in ate

ballast bags with an air pump! When carrying full bags, never throw it to the surface. By ground impact an

internal pressure increase, what can lead to the bag rupture. Lay bags to the ground to ideal positions of

legs. Side to lay down is a side with hooks. A valve is place on a top side. Hooks must be directed diagonally

to the tent, facing to aluminium buckles of tent.

SQUARE SETUP MANUAL

WIR BLASEN AUF. SIE FALLEN AUF. www.noproblaim.at

NOTE

Avoid open ame, sharp objects and chemicals.

Clean by water, technical alcohol and detergent (no aggressive) only! Do not use aggressive dissolvent!

Store dry!

Tent is made from 100% polyester and polyurethane bladder.

It can be damaged by rough handling!

Do not overpressure!

By exposing to sun, internal pressure is naturally increasing.

Overpressure is released by RED overpressure valve, there must be placed on right position.

Once the air comes cooler (mainly in the evening), internal pressure goes down.

There can be the necessity to rell missing air.

Use all walls, visors and tunnels after purchase. Residual chemical substances from sublimation process can

continue and cause migration of color. These chemicals have to be separated. Risk of further migration of

color has been reduced by using or ventilation of walls visors and tunnels.

Always screw all valves back into their position before putting the tent into the bag! Unscrew valves in bag

can damage valve bases.

SQUARE SETUP MANUAL

Aufbauvideo Pneu Zelt

https://www.youtube.com/user/noproblaimvideos

NOTE

no problaim Werbeträger GmbH

Schuster-Straße 4, 2111 Tresdorf / Wien, ÖSTERREICH

Tel +43 (0)2262 64 65 00, Fax +43 (0)2262 64 65 09, [email protected], www.noproblaim.at

Alle Angaben ohne Gewähr. Änderungen und Druckfehler vorbehalten. Bezeichnungen/Produkte/Fotos/Skizzen und Texte sind geistiges Eigentum

der no problaim Werbeträger GmbH. Sie dürfen ohne ihr Einverständnis weder vervielfältigt noch reproduziert werden. Es gelten die Allgemeinen

Geschäftsbedingungen der no problaim Werbeträger GmbH in ihrer jeweils letztgültigen Fassung.

Inhaltsverzeichnis

Andere no problaim Zelt Handbücher

no problaim

no problaim CUBE Benutzerhandbuch

no problaim

no problaim Pneu Zelte Lite Benutzerhandbuch

Beliebte Zelt Handbücher anderer Marken

OZTENT

OZTENT JV SIGNATURE EDITION Bedienungsanleitung

GigaTent

GigaTent Summer Chalet Mini Tent Bedienungsanleitung

Coleman

Coleman 2000007827 Handbuch

ShelterLogic

ShelterLogic 107153 Bedienungsanleitung

Outsunny

Outsunny 84C-230 Bedienungsanleitung

Napier

Napier SPORTZ COVE 61 Series Bedienungsanleitung

EuroTrail

EuroTrail ATLANTIS PRO Bedienungsanleitung

Reimo

Reimo Marina Bedienungsanleitung

TiiTENT

TiiTENT TB300 Bedienungsanleitung

Coleman

Coleman 2000033134 Installationsanleitung

Ozark Trail

Ozark Trail W784.1 Kurzanleitung

SlingFin

SlingFin CrossBow 2 Bedienungsanleitung

Coleman

Coleman 9600-141 Bedienungsanleitung

Palram

Palram Arizona 5000 Wave - WINGS Bedienungsanleitung

COVERPRO

COVERPRO 56184 Montageanleitung

Vango

Vango Zenith 100 Bedienungsanleitung

Costway

Costway PATIOJOY OP70818 Bedienungsanleitung

Clarke

Clarke PUC 88 Bedienungsanleitung

no problaim SQUARE Benutzerhandbuch

Beliebte Zelt Handbücher anderer Marken