Nokia NetMonitor Bedienungsanleitung

Nokia

NetMonitor

Manual

Version 0.5

Base document : Flipo ( [email protected] )

PDF + Enhancements to base document : nobbi ( [email protected] )

Graphics : nobbi

Phone Models/Software versions

31xx/81xx

Old phones netmonitor has some differences when compared with the newer models, but this manual can be used

as a guide, because the overall working method and the contents are very similar.

51xx/61xx/71xx/88xx/91xx/32xx

This document covers the majority of menus from these phones netmonitor. Some of them may have little

differences, like missing/additional menus, different info, etc.

The 51xx and 61xx pages are almost identical. The 32xx has some more pages, which are not very well

documented yet. The 71xx has a whole bunch of pages concerning W@P. The 91xx pages are almost identical to

the 6110 ones.

The goal right now is to make an accessible manual, that will get better over the time. Please contribute with all

the info that you find relevant.

Information Sources :

[ 1 ] Netmonitor description (RD843.txt) from Nokia Mobile Phones

[ 2 ] Marcin Wiaceks homepage ( http://marcin-wiacek.topnet.pl )

Menu Modes

There are three Menu Display modes:

- execute mode

- data display mode

- help mode

Different modes are marked in this manual as follows:

************** ++++++++++++++ ##############

* * + + # #

* Execute * +Data display+ # Help #

* Mode * + Mode + # Mode #

* * + + # #

************** ++++++++++++++ ##############

The execute mode is entered from the menu by scrolling and selecting or shortcut. If the

test index entered pertains to a test that resets a timer (test 80) for example, then the

timer is reset as soon as the Ok button has been pressed in the menu, and the data display

mode takes over. In other words, the execute mode is of the one-shot type. To run another

test in the execute mode, the Field Test Display menu must be re-activated.

During the data display mode, the field test data (e.g. carrier, power level, cell) is

visible on the main display. During the help mode, one screen of instructions is shown for

each test to make it easier to identify the test in question. A long press of asterisk (*)

is used to toggle between these two modes.

(on some 3110 versions, the help screens follow the data display modes on the list)

The arrow keys (^,v) offer an easy way to switch to another test without using the menu.

However, the data display mode remains, i.e. nothing will be executed or set on although

such tests would be passed. This is to prevent the user from accidentally clearing any

valuable data. (see 3.7.2 for details and 2.5 for recommendations).

The help mode is also a non-execute mode. Display numbers have been selected in such way

that no 5-terminated test number is an execute display.

Display 1 –Serving cell info

++++++++++++++ ##############

+abbb ccc ddd+ #CH RxL TxPwr#

+ e ff g mmmm+ #TS TA RQ RLT#

+ nnn ppp+ # C1 C2 #

+ oooo + # CHT #

++++++++++++++ ##############

aH, if carrier numbers are scrolled when hopping is on. Otherwise ' '.

bbb When mobile is on a TCH :

DCH carrier number in decimal.

When mobile is NOT on a TCH :

CH means carrier number in decimal.

If hopping is on, used channels are scrolled when display is updated.

ccc rx level in dBm, minus sign is not shown if <=-100

ddd tx power level. If transmitter is on, symbol * is shown in front of the power

level value.

eTime Slot, range is 0 - 7

ff Timing advance, range is 0 – 63

gRX quality (sub), range is 0 - 7

mmmm Radio Link Timeout value. If value is negative, 0 is shown.

Maximum value is 64. When mobile is NOT on TCH then xx is shown.

nnn value of the path loss criterium (C1). Range is -99 - 999.

oooo type of current channel:

THR0 : TCH HR subchannel 0

THR1 : TCH HR subchannel 1

TFR : TCH FR

TEFR : TCH EFR

F144 : TCH FR data channel, speed 14.4 kbps

F96 : TCH FR data channel, speed 9.6 kbps

F72 : TCH FR data channel, speed 7.2 kbps

F48 : TCH FR data channel, speed 4.8 kbps

F24 : TCH FR data channel, speed 2.4 kbps

H480 : TCH HR data channel, speed 4.8 kbps, subch 0

H481 : TCH HR data channel, speed 4.8 kbps, subch 1

H240 : TCH HR data channel, speed 2.4 kbps, subch 0

H241 : TCH HR data channel, speed 2.4 kbps, subch 1

FA : TCH FR signalling only (FACCH) channel

FAH0 : TCH HR signalling only (FACCH) channel, subch 0

FAH1 : TCH HR signalling only (FACCH) channel, subch 1

SDCC : SDCCH

AGCH : AGCH

CCCH : CCCH

CBCH : CCCH and cell broadcast receiving on

BCCH : BCCH

SEAR : SEARCH

NSPS : MS is in ’no service, power save’ state

ppp value of the cell reselection criterium (C2).

Range is -99 to 999. If phone is phase 1 then C1 value is shown.

Display 2 –More info about serving cell

++++++++++++++ ##############

+ aa b c Bdd + #PM RAR Ro BC#

+ ee f + #RelR QLF #

+ ggg hh iii + #CRO TO PenT #

+ H=j mm nn + #H MAIO HSN #

++++++++++++++ ##############

aa paging mode

NO : normal paging

EX : extended paging

RO : paging reorganization

SB : same as before

bmaximum number of Random Access retransmission

croaming indicator, values are 'R' or ' '.

Bdd Letter B and BSIC value, range is 0 - 63.

ee Reason of last call release

fRX quality (full), range is 0 - 7

ggg Cell reselection offset, range 0 - 126 dB.

0 - 63 * 2 dB. 'xxx' in dedicated mode.

hh Temporary offset, range 0 - 60 dB.

0 - 7 * 10 dB. 70 dB means infinite time.

'xx' in dedicated mode.

iii Penalty time, range 0 - 620 s.

0 - 31 * 20 s. 'xxx' in dedicated mode.

jHopping channel

0Single RF channel

1RF hopping channel

mm mobile allocation index offset, MAIO

Range: 00 to 63 / xx when H=0

nn hopping sequence number, HSN

Range: 00 to 63 / xx when H=0

Display 3 –Serving cell, 1st and 2nd neighbour

++++++++++++++ ##############

+aaabbbcccddd+ #SCH C1 rx C2#

+aaabbbcccddd+ #1CH C1 rx C2#

+aaabbbcccddd+ #2CH C1 rx C2#

+ ef gh + # 1N 2N #

++++++++++++++ ##############

1. row: serving cell information

2. row: 1. neighbour information

3. row: 2. neighbour information

4. row, ef: 1. neighbour information

4. row, gh: 2. neighbour information

aaa carrier number in decimal

bbb idle mode : C1 value, range is -99 - 999

ded. Mode : 'B' and BSIC value

ccc RX level in dBm, minus sign is not shown if <=-100

ddd C2 value, range is -99 - 999

e,g F : cell is in a forbidden location area

f,h B : cell is barred

N : cell is normal priority

L : cell is low priority

Display 4 & 5 –3rd to 8th neighbour cell

++++++++++++++ ##############

+aaabbbcccddd+ #3CH C1 rx C2#

+aaabbbcccddd+ #4CH C1 rx C2#

+aaabbbcccddd+ #5CH C1 rx C2#

+ ef gh ij + # 3N 4N 5N #

++++++++++++++ ##############

1. row: 3./6. neighbour information

2. row: 4./7. neighbour information

3. row: 5./8. neighbour information

4. row, ef: 3./6. neighbour information

4. row, gh: 4./7. neighbour information

4. row, ij: 5./8. neighbour information

aaa carrier number in decimal

bbb idle mode : C1 value, range is -99 - 999

ded. Mode : 'B' and BSIC value

ccc rx level in dBm, minus sign is not shown if <=-100

ddd C2 value, range is -99 - 999

e,g,i F : cell is in a forbidden location area

f,h,j B : cell is barred

N : cell is normal priority

L : cell is low priority

Display 6 –Network selection display

++++++++++++++ ##############

+aaabb aaabb+ #LReg 1_For#

+aaabb aaabb+ #1_Pre 2_For#

+aaabb aaabb+ #2_Pre 3_For#

+aaabb aaabb+ #3_Pre 4_For#

++++++++++++++ ##############

This display shows the last registered networks country code (MCC) and

network code (MNC) as well as the codes for four forbidden networks

and the first 3 preferred networks.

If a three-digit MNC is used (GSM1900), display looks different:

++++++++++++++

+aaabbbaaabbb+

++++++++++++++

1. row: last registered network - 1st forbidden network

2. row: 1st preferred network - 2nd forbidden network

3. row: 2nd preferred network - 3rd forbidden network

4. row: 3rd preferred network - 4th forbidden network

aaa country code coded in BCD

bbb network code coded in BCD, third digit can be 'F'

Display 7 –System information bits for serving cell

++++++++++++++ ##############

+E A H C I BR+ #Serving Cell#

+a b c d e fg+ #System Info #

+ECSC 2Ter MB+ #Bits #

+ h i j+ # #

++++++++++++++ ##############

a1 is shown if emergency calls are supported

b1 is shown if attach-detach-procedure is allowed

c1 is shown if half rate channels are supported

d1 is shown if C2 values are broadcasted

e1 is shown if system information 7 and 8 are broadcasted

f1 is shown if cell broadcast is supported

g1 is shown if re-establishment is supported

The following items are used only in dualband phones:

hIn idle mode 1 is shown if Early Classmark (ECSC) sending is supported.

In dedicated mode (conversation) X is shown.

iIn idle mode 1 is shown if 2Ter messages are supported.

In dedicated mode (conversation) X is shown.

jMultiBand reporting decimal value (0,1,2,3) is shown if supported.

This is shown both in idle and dedicated mode.

The following is picked from Phase2+ ETSI ETS 300578 (GSM 05.08 version 4.22.1), Section

8.4.3 "Additional cell reporting requirements for multi band MS".

For a multi band MS the number of cells, for each frequency band supported, which shall be

included in the measurement report is indicated by the parameter, MULTIBAND_REPORTING. The

meaning of different values of the parameter is specified as follows:

Value Meaning

00 Normal reporting of the six strongest cells, with known and allowed NCC part of

BSIC, irrespective of the band used.

01 The MS shall report the strongest cell, with known and allowed NCC part of

BSIC, in each of the frequency bands in the BA list, excluding the frequency

band of the serving cell. The remaining positions in the measurement report

shall be used for reporting of cells in the band of the serving cell. If there

are still remaining positions, these shall be used to report the next strongest

identified cells in the other bands irrespective of the band used.

10 The MS shall report the two strongest cells, with known and allowed NCC part of

BSIC, in each of the frequency bands in the BA list, excluding the frequency

band of the serving cell. The remaining positions in the measurement report

shall be used for reporting of cells in the band of the serving cell. If there

are still remaining positions, these shall be used to report the next strongest

identified cells in the other bands irrespective of the band used.

11 The MS shall report the three strongest cells, with known and allowed NCC part

of BSIC, in each of the frequency bands in the BA list, excluding the frequency

band of the serving cell. The remaining positions in the measurement report

shall be used for reporting of cells in the band of the serving cell. If there

are still remaining positions, these shall be used to report the next strongest

identified cells in the other bands irrespective of the band used.

Display 10 –Paging Repeat Period, TMSI, Location Update Timer, AFC and AGC

++++++++++++++ ##############

+TMSIaaaaaaaa+ #TMSI(hex) #

+T321:bbb/ccc+ #T3212ctr/tim#

+PRP:d ee ff+ #PaRP DSF AGC#

+ ggggg hhh + # AFC Ch #

++++++++++++++ ##############

aaaaaaaa last assigned TMSI value in hex format

bbb Current value of T3212 counter (range is 000 - 'ccc', where 1 means 6 min

time. So, if this value is 2 less than 'ccc' then next periodic location

updating will be made within 2 * 6 min = 12 minutes.

ccc Timeout value of T3212 counter (range is 000 - 240, where 1 means 6 min time

between location updates and 240 means 240 * 6 min = 24 h between location

updates. 000 means that a periodic location update will not occur) This

value is received from the network.

dValue of paging repetition period (range is 2 – 9, which means paging will be

in every Xth multiframe. When paging is in every second multiframe, mobile

takes more current than if it were in every 9th multiframe)

ee Downlink signalling failure value. If value is negative, 0 is shown. Maximum

value is 45. When mobile is on TCH then xx is shown.

ff Gain value on TCH/SDCCH, range is 0 - 93

ggggg VCTCXO AFC DAC control, range is -1024 - 1023

hhh Serving cell channel number

Display 11 –Network parameters

++++++++++++++ ##############

+CC:aaa NCbbb+ # MCC MNC #

+ LAC:ccccc + #LocAreaCode #

+ CH : dddd + #ServChannel #

+ CID:eeeee + # CellId #

++++++++++++++ ##############

aaa MCC value in decimal (MCC=Mobile Country Code)

bbb MNC value in decimal (MNC=Mobile Network Code)

Three digits are shown only in GSM1900.

Two digits are shown in GSM900 and GSM1800.

ccccc LAC value in decimal (in older SW-versions this value is in hexadecimal)

dddd Serving cell channel number

eeeee Cell Identifier in decimal (in older SW-versions this value is in hexadecimal)

Display 12 –Ciphering, hopping, DTX Status and IMSI

++++++++++++++ ##############

+CIPHER :aaa + #CipherValue #

+HOPPING:bbb + #HoppingValue#

+DTX :ccc + #DTXValue #

+IMSI :ddd + #IMSIAttach #

++++++++++++++ ##############

aaa ciphering value, OFF/A51/A52

bbb hopping value, ON/OFF

ccc DTX value ON/OFF

ddd IMSI attach

ON : IMSI attach on

OFF : IMSI attach off

These values are updated only on when on a TCH.

Display 13 –Uplink DTX switching display

************** ##############

*aaaaaaaaaa * #DTXMode #

*DTX(DEF):bbb* #DefaulDTXSta#

*DTX(BS) :ccc* #DTXValFromBS#

* * # #

************** ##############

With this display it is possible to change wether MS to use DTX or not.

This display must be activated from MENU to change DTX state. When MENU is not active and

the user is scrolling field test displays with NEXT and PREVIOUS, the DTX state will not be

changed.

aaaaaaaaaa status of switched mode.

DTX:ON : MS uses DTX

DTX:OFF : MS does not use DTX

DTX:DEF : MS use default state of DTX

NOTALLOWED: BS does not allow MS to decide if it uses

DTX or not.

bbb default state of DTX in MS. The value is either ON or OFF

ccc is DTX value from BS

MAY : BS allows MS to decide if it uses uplink DTX or not

USE : BS controls MS to use DTX (on uplink)

NOT : BS controls MS not to use DTX (on uplink)

Display 14 –Toggle Screening Indicator

************** ##############

* SCREENING * #Use menu to #

* INDICATOR * # change #

* IS XX * XX : 00 or 01 # Screening #

* * # indicator #

************** ##############

When selected, changes the value of the Screening Indicator from 0 to 1 and

vice versa.

Display 17 –Switch BTS_Test Status

************** ************** ##############

* * * * #Use menu to #

* BTS TEST * * BTS TEST * #toggle BTS #

* ON * * OFF * #test ON/OFF #

* * * * # #

************** ************** ##############

This display is used to toggle the BTS_TEST flag in EEPROM. If BTS_TEST

is set then each time the mobile sends a search list it uses only the carrier

number stored on SIM phonebook location 33. Also the neighbour information from

system information messages is ignored. If the BTS_TEST flag is not set,

then the value of SIM phonebook location 33 is ignored and the mobile behaves

normally (i.e. does neighbour measurements according to GSM specifications).

To activate BTS TEST perform the following steps:

- Save desired channel number in SIM phonebook location 33.

- Select display 17 in execute mode

- Switch power off and on

If activation succeeded, you will read "BTS TEST ON" in display 17.

To deactivate BTS tests either select display 17 in execute mode or

save number 0 in SIM phonebook location 33 and switch power off and on.

NOTE! The display does not show the value of the BTS_TEST flag in EEPROM.

Although the value is set, BTS_TEST can be off. If there is no legal

carrier number in SIM phonebook location 33 (GSM900: 1-124, GSM1800: 512-885) the

display shows that BTS_TEST is off. Also if the mobile was already

registered to some carrier before switching BTS_TEST status, the display

can show a different value from the one in EEPROM.

Display 18 –Lights status control

Forces keyboard and display lights on/off while displaying any netmonitor screen.

************** ************** ##############

* * * * #Use menu to #

* LIGHTS * * LIGHTS * # toggle #

* ON * * OFF * # lights #

* * * # ON/OFF #

************** ************** ##############

Display 19 –Toggle Cell Barred Status

************** ************** ************** ##############

* * * * * * #Use menu to #

* CELL BARR * * CELL BARR * * CELL BARR * #toggle cell #

* ACCEPTED * * REVERSE * * DISCARD * #barr status #

* * * * * * #DIS/ACC/REV #

************** ************** ************** ##############

This test is meant to be used when some cells are tested before taking them into commercial

use. By setting the CELL_BARRED to on in the base station normal GSM phones will not try to

camp on these barred cells.

By selecting CELL BARR REVERSE, the MS will only use the cells which have CELL_BARRED set.

By selecting CELL BARR DISCARD, the MS will use all cells, irrespective wether CELL_BARRED

is set or not.

NOTE: If a cell has been selected before barring state in phone is changed the selected cell

will remain the current cell. After the next cell reselection the cell barring state is

working as expected.

Display 20 –Charging state

************** ##############

* aaa bbbbb * #BatVol ChMod#

* Tccc dddd * #Btemp ChTime#

* Ceee Wfff * #ChrgVol Pwm #

* gggg hhhh * # Btyp BFDC #

************** ##############

aaa Battery voltage in decimal, range is 0.00 - 9.99 V, decimal point is not shown;

e.g. 7.19 V is shown as 719 on the display

bbbbb Charging mode 5 digit symbol:

xxxxx : Charger not connected or charging disabled.

BatCk : Battery testing is going.

BSIFa : Charging off because of battery BSI measurement failed.

CelBr : Charging off because one or more cells broken inside battery.

ChaCk : EM is checking charger.

Charg : Charging.

ColdC : Cold charging.

ColdM : Battery cold and maintenance going.

CurFa : Charging off because charger current measurement failed.

DisCh : Battery discharging going.

F_Che : Fast charging checks.

Faile : Failure.

FastC : Fast charging going.

FullM : Battery full and maintenance going.

HotM : Battery hot and maintenance going.

I_Che : Init checks.

InitC : EM charging is being initialized.

L_Che : Li charging checks.

LiAFu : PWM level is below the battery full limit.

LiDCH : Li-ion DCH charging.

LiFul : PWM has been below the battey full limit for a certain time

that is specified for full battery.

LiHot : Li-ion hot charging.

LithC : Charging of Lithium-ion battery.

LiTxO : TX on and Li charging going.

LNFTx : TX on, Li charging going and battery is not full anymore.

M_Che : Maintenace charging checks.

MaBFD : Maintenace BFD charging.

Maint : Maintenance charging.

TmpFa : Charging off because of battery NTC measurement failed.

TxNoF : TX on, Ni charging going and battery is not full anymore.

TxOnC : TX on and Ni charging going.

VolFa : Charging off because charger voltage measurement failed.

ccc Battery temperature in centigrade, from -30 to +90.

ddd Charging time. Format is HMM. Timer is automatically reset and started when

charger is connected and stopped when battery is full or charger is

disconnected.

eee Charger voltage in decimal, range is 0.0 - 18.7 V, decimal point is not shown.

fff Charge control output, decimal, range is 000 - 255.

gggg Lithium battery type (BSI value multiplied by 4), or NiMH battery size.

hhhh Battery full delay counter. When battery is getting full and charging current is

less than predefined limit, this timer will be started. If timer reaches 0,

charging will be stopped.

Dieses Handbuch passt für folgende Modelle

Andere Nokia Software Handbücher

Nokia

Nokia FRING version 3.23 Bedienungsanleitung

Nokia

Nokia 1261 - Cell Phone - AMPS Bedienungsanleitung

Nokia

Nokia SYMBIAN S60 Bedienungsanleitung

Nokia

Nokia E90 Communicator Bedienungsanleitung

Nokia

Nokia 5500 Bedienungsanleitung

Nokia

Nokia E61 Bedienungsanleitung

Nokia

Nokia NPS6113000 - Secure Access System Bedienungsanleitung

Nokia

Nokia 6340i - Cell Phone - AMPS Bedienungsanleitung

Nokia

Nokia City Lens Bedienungsanleitung

Nokia

Nokia IPSO 4.0 Bedienungsanleitung

Nokia

Nokia 6360 Bedienungsanleitung

Nokia

Nokia 6310 Montageanleitung

Nokia

Nokia IPSO IP350 Bedienungsanleitung

Nokia

Nokia E66 Bedienungsanleitung

Nokia

Nokia 5120 - Cell Phone - AMPS Bedienungsanleitung

Nokia

Nokia 7250 Montageanleitung

Nokia

Nokia 9201597R001 Bedienungsanleitung

Nokia

Nokia Series 60 Bedienungsanleitung

Nokia

Nokia Symbian S60 v5 Bedienungsanleitung

Nokia

Nokia 3320, 3360 Bedienungsanleitung

Nokia

Nokia 0276822 - Navigation Kit - GPS Bedienungsanleitung

Nokia

Nokia NRB0002000 - Intellisync Call Connect Bedienungsanleitung

Nokia

Nokia Intellisync 9.2 Bedienungsanleitung

Nokia

Nokia N86 8MP Bedienungsanleitung

Beliebte Software Handbücher anderer Marken

COMPRO

COMPRO COMPROFM Bedienungsanleitung

Muratec

Muratec OFFICEBRIDGE ONLINE Bedienungsanleitung

Oracle

Oracle Contact Center Anywhere 8.1 Bedienungsanleitung

Adobe

Adobe 65007312 - Photoshop Lightroom Handbuch

Avaya

Avaya NULL One-X for RIM Blackberry Bedienungsanleitung

HP ProLiant BL420c Bedienungsanleitung

PS Audio

PS Audio PowerPlay Betriebsanleitung

Brady

Brady LOCKOUT PRO 3.0 Service-Handbuch

Avaya

Avaya Interaction Center Bedienungsanleitung

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Handbuch

Novell

Novell GROUPWISE 8 - INTERNET AGENT Bedienungsanleitung

Oracle

Oracle Application 9i Bedienungsanleitung

Acer

Acer RDM Bedienungsanleitung

Canon

Canon Vixia HF21 Bedienungsanleitung

Canon

Canon ZR950 Bedienungsanleitung

Samsung

Samsung Auto Backup Bedienungsanleitung

Polycom

Polycom Vortex EF2201 Montage- und Bedienungsanleitung

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Bedienungsanleitung