Nokta FORS relic Bedienungsanleitung

Thank you for choosing and purchasing our Nokta FORS Relic detector.

FORS Relic, developed by Nokta's expert engineering team experienced in metal

detection, is a professional metal detector ideal for coins and relics.

Manufacturing high-tech metal detectors since 2001, Nokta Detectors has played

a key role in the development of this sector. Nokta Detectors is particularly known

for its technological know-how and professional staff.

Seeking to create different kind of technology, Nokta Detectors offers both

high-quality products and services to its consumers all around the world. Nokta

Detectors has been operating under the principle that environmental and

community responsibility, customer satisfaction and insistence on high-quality are

of the utmost importance.

Nokta Detectors aims to remain a leading pioneer in its sector, winning the trust of

its consumers and always being the preferred choice for metal detecting.

INTRODUCTION

WARNINGS ..........................................................................................................................................................

PARTS and ASSEMBLY ..............................................................................................................

CORRECT WAY OF HOLDING and SWEEPING ............................................

BATTERIES ..........................................................................................................................................................

DEVICE INTRODUCTION ..................................................................................................

CONTROLS ....................................................................................................................

MAIN SCREEN ...........................................................................................................

NUMERIC DISPLAY ..................................................................................................

MENU ................................................................................................................................

SEARCH MODES .........................................................................................................................

GROUND BALANCE ..............................................................................................................

SENSITIVITY and THRESHOLD ........................................................................................

iMASK ..........................................................................................................................................................

TARGET ID and ID MASKING ..................................................................................

PINPOINT ........................................................................................................................................................

DEPTH INDICATION ........................................................................................................................

SWEEP SPEED and TARGET IDENTIFICATION .......................................

LARGE or SHALLOW TARGETS .......................................................................................

FALSE SIGNALS and COMMON CAUSES ........................................................

MAGNETIC MINERALIZATION LEVEL ...................................................................

HOT ROCKS AND SEARCHING IN ROCKY AREAS ..................

EFFECTS OF HOT ROCKS IN GROUND TRACKING ..........................

METALS UNDER HOT ROCKS .................................................................................

SEARCHING IN SHALLOW WATER AND ON THE BEACH .......

MESSAGES ....................................................................................................................................................

FACTORY and STARTUP SETTINGS ...............................................................

TECHNICAL SPECIFICATIONS ..........................................................................................

2-3

6-12

6-7

7-8

9-12

12-14

15-18

19-20

20-21

24-25

25-26

27-28

TABLE OF CONTENTS

WARNINGS

LEGAL WARNINGS

► When using the device, comply with all applicable laws and regulations. Do not use the

device in private premises, historic sites and military zones. Notify the authorities of any

historical or cultural findings.

WARNINGS ABOUT THE DEVICE

► This is a high-tech electronic device. Do not assemble or use the device before reading

the user manual.

► Do not expose the device or the search coil to very hot or cold conditions for extended

periods of time. (Storage Temperature: -20°C (-4°F) / 60°C (140°F))

► Do not immerse the device or its accessories (except the search coil) in water; do not

expose them to extreme humid conditions.

► Protect the device from external impact, especially during transportation.

►The device can only be opened and repaired by authorized service technicians. The

warranty will be voided if the device is opened by you or an unauthorized person.

IMPORTANTIMPORTANT

Do not use the device indoors. The device

will constantly give target signals inside

places like homes where there are many

metals present. Use the device outdoors, in

open fields.

Do not let another detector or an

electromagnetic device come in close

proximity (10m (33ft.)) to the device.

Do not carry any metal objects while using

the device. Keep the device away from your

shoes while walking. The device may detect

the metals on you or inside your shoes as

targets.

For Consumers within the European Union: Do

not dispose of this equipment in general

household waste. The crossed wheeled bin

symbol on this equipment indicates this unit

should not be disposed of in general household

waste, but recycled in compliance with local

government regulations and environmental

requirements.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interferen-

ce that may cause undesired operation.

Page 1

BATTERY

PARTS and ASSEMBLY

Attach the right/left armrest components to the

S-rod with the bolts and nuts as seen in the

picture. Do not tighten the nuts but rather leave

them loose (these will be tightened after the

system box is attached).

Place the system box on the rail behind the

armrest and push forward. Then secure by

tightening the nuts. Attach the armrest strap

by inserting it through the holes.

1) System Box

2) Handle and S-Rod

3) Right/Left Armrest

Components

4) Armrest Strap

5) Search Coil

6) Telescopic Shaft

7) Bolts, Nuts and

Washers

8) 3 Cable Clamps

9) 4 AA Batteries

10) Headphones

Page 2

1)To attach the telescopic shaft to

the S-rod, first loosen the twist

lock. 2)By holding the metal pin

pressed, insert the telescopic

shaft into the S-rod and click the

pin into its hole. 3)Secure it by

tightening the twist lock. 4)After

adjusting the shaft length to your

height, secure by tightening the

twist lock.

1)Place the washers into the

openings at the end of the

telescopic shaft. 2)Place the shaft

on the coil as shown in the

picture. 3)Secure by tightening

the bolt and the wingnut.

Wrap the coil cable around the

shaft all the way up as shown in

the picture and after inserting it in

the coil input socket underneath

the system box, secure it by

twisting the connector. Pay

attention to not wrap the cable

too tight during this step. Insert

the handle cable in the socket

underneath the system box

(HANDLE) and secure it by

twisting the connector. Finally,

secure the cable by attaching the

clamps at 3 different spots.

PARTS and ASSEMBLY

Page 3

CORRECT WAY OF HOLDING

CORRECT WAY OF SWEEPING

It is very important to adjust the shaft to your

height correctly to be able to search without

discomfort and fatigue.

Adjust the height of the shaft so that you are

standing in an upright position, your arm is

relaxed and the search coil is approximately 5cm

(~2'') above the ground.

It is important to keep the search coil

parallel to the ground in order to get

accurate results.

The search coil must be parallel to the

ground at all times.

Wrong search coil angle

Incorrect way of sweeping

Wrong search coil angle Correct search coil angle

Correct way of sweeping

Shaft height is wrong. Shaft height is correct.

Page 4

Target

General Search

GEN

ROCK IRON

Target

General Search

GEN

Target

Low Battery

- -

ROCK IRON

Target

General Search

GEN

BATTERIES

The device comes with 4 AA Alkaline batteries.

Slide and remove the battery compartment cover by pressing the latch. Insert the batteries

paying attention to the + (plus) and – (minus) poles.

When batteries are full, they will provide approximately 25-30 hours of use. Different types

or brand of batteries may have different lifetimes.

For best performance, using AA Alkaline batteries is recommended. You may also use high

quality rechargeable Ni-MH batteries. Rechargeable batteries with higher mAh (capacity)

ratings will provide longer run times.

LOW BATTERY

The battery icon on the LCD panel indicates the battery life status. In addition, a warning

message will appear on the screen when the batteries are low. After the low battery

warning, the batteries will run approximately 3-4 more hours. This runtime will vary based

on the remaining battery charge. Ni-MH batteries have lower voltage so their remaining

runtime will be longer than Alkaline batteries. This does not affect the total runtime.

Page 5

5 7 6

1- POWER SWITCH:

To turn on the device, press the power switch to (1) position. The startup tone will be heard

and after the FORS Relic logo is displayed for a short period of time, the main screen will

come up on the LCD panel.

2- GROUND TRACKING SWITCH:

When the ground tracking is active (at 1 position), the device will track the changes in

ground and automatically adjust the ground balance to suit. The invisible changes in

ground affects the detection depth as well as the discrimination ability of the device so you

can improve the performance of the device by activating this feature on suitable ground.

You can find more details about ground tracking on page 17.

3- MENU AND SETTINGS BUTTONS:

These buttons allow you to access the menu and scroll through options as well as adjust

device settings.

On the main screen, you can access the menu by pressing one of the up/down/+/- buttons.

You can select the menu options with the up and down button and change the value with

the + (plus) and - (minus). Pressing these buttons in a specific order will result in ''resetting

factory settings'' or ''saving startup settings''. You can find more details about this on page

27-28 under the title FACTORY and STARTUP SETTINGS.

DEVICE INTRODUCTION

CONTROLS

Page 6

If you press and hold any of these buttons at startup, system information including

software version and the serial number of the device will appear on the screen after the

Nokta logo is displayed for a few seconds. This information will stay on the screen as long

as you hold the button pressed. Please have his information ready when you contact your

dealer regarding your device.

4- GROUND BALANCE BUTTON:

Allows you to ground balance manually or automatically before or during your search. By

keeping this button pressed and pumping the coil, you can quickly ground balance the

device at any time. When you press and release the button, you can ground balance

manually by changing the ground balance value on the screen. Please read pages 15-18 for

more information on ground balance.

5- PINPOINT SWITCH:

It is used to find the exact location of the target. Pinpointing saves you digging time by

narrowing down the location of a buried target. Please refer to PINPOINT section on page 22

for more details.

6- LED FLASHLIGHT:

Is used for illumination at night or in dark places. The flashlight will not work when the

device is off. Having the flashlight on will affect power consumption so we recommend to

keep it off when not needed.

7- LED FLASHLIGHT POWER SWITCH:

Is used to turn on/off the flashlight.

You can see all the information you need during searching, ground balancing, and

pinpointing on the main screen. The information is as follows:

Target

General Search

GEN

MAIN SCREEN

DEVICE INTRODUCTION

During Searching:

1) TARGET ID

2) TARGET ID INDICATOR (HORIZONTAL BAR)

3) MAGNETIC MINERALIZATION LEVEL

4) GROUND TRACKING ON/OFF

5) SEARCH MODE or WARNING MESSAGE

6) BATTERY LEVEL

Page 7

Inhaltsverzeichnis

Andere Nokta Sicherheitssensor Handbücher

Nokta

Nokta RS PinPointer Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung