Nomadic Display HangTen Handbuch
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Setup Instructions
HangTen
CONGRATULATIONS!
Like thousands of Nomadic Display owners around the world, you now own the
highest quality portable/modular display. Your Nomadic HangTen is specially
designed to give you the ultimate in versatility. Original, Classic (curved) and Plus
(straight) frame systems integrate to meet your growing exhibit demands. And your
100% satisfaction is guaranteed by Nomadic.
The Lifetime Warranty
Your HangTen frame is guaranteed for life. If it ever fails to
function Nomadic Display will repair it free of charge for as long
as you own it. Be sure to complete and return the enclosed
warranty card immediately.
Made by Nomadic Display
Superior in design and strength, your Nomadic Display is built in Nomadic’s own
manufacturing plants in the U.S. and Ireland. We use only premium grade materials
and take pride in maintaining the highest standards of craftsmanship. Your display
is delivered to you packed for maximum protection and quick assembly.
Nomadic Cares, Please Recycle
All Nomadic aluminum frames and cases can be recycled.
We recommend that you assemble and repack your display
prior to your first event. It is important to follow each step in
the order indicated. If you need additional assistance or have
any questions, please call your nearest Nomadic LifeLine:
North America: Ireland/Europe:
800.732.9395 + 353.1.208.7261
United Kingdom:
07699 734215
TABLE OF CONTENTS
Frames
oFrame Setup ...................................................................... 2
Graphics
oGraphic & Light Setup ........................................................ 3
Accessories
oHeader Setup...................................................................... 4
oProduct Pedestal ................................................................ 5
oSmall Monitor & Keyboard Shelf Setup .............................. 6
oMedium Monitor Setup....................................................... 7
oLarge Monitor Setup........................................................... 8
oFin Setup, Original .............................................................. 9
oFin Setup, Classic/Plus ...................................................... 10
oVertical Profile Setup .......................................................... 11
oStand-alone Counter Setup................................................ 12
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Connect top H1/H2 extrusion to top V1 and
V2 extrusions (track on top). Lock with hex
wrench.
Lift frame by support extrusion and walk it
back into an upright position.
Connect bottom H1/H2 extrusion to
bottom V1 and V2 extrusions (track on
bottom). Lock with hex wrench.
Your Original frame is now ready for
graphics.
Slide monitor extrusion into place. Lock with hex wrench at the top and
bottom.
Your Plus frame is now ready for
graphics.
Your Classic frame is now ready for
graphics.
Frame Setup Instructions
Place extrusions with locking hole facing
up and connect.
Monitor top to Monitor bottom
Top V1 to Bottom V1 / Top V2 to Bottom V2
Bottom H1 to Bottom H2 / Top H1 to Top H2*
Top H1 to Top H2*
If you have a header, slide H channel
above track. Lock tightly with hex wrench
provided.
Place foot upright on floor. Insert V1
extrusion into foot channel with locking
holes facing inward. Lock with hex
wrench. Repeat with V2 extrusion.
HangTen
Remove HangTen parts from black bag
and lay them out label side up. You will
build the frame on the ground facing
down.
Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.
Frames • 2
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Tuck the graphic edge from center out to
left and right corners along the top and
then bottom track.
Lights are connected to holes on the
top of your frame.
Fold excess corner fabric under and
press edge of fabric graphic onto
Velcro® on one side. Work your way
down the side of the frame.
Insert the peg base of the lights into a
hole on the top part of the frame.
Pull taut as you press edge of fabric
graphic onto Velcro®. Work your way
down the side of the frame. Repeat on
other side.
Your assembled HangTen display is now
ready for accessories.
Swivel fixture to adjust position.
Graphic & Light Setup Instructions
Lift assembled frame into upright
position. Insert top corners of fabric
graphic plastic edge into the horizontal
track along the top H1/H2 extrusions.
Tuck the plastic edge into the horizontal
groove about 3” to secure the top two
corners.
Insert lower corners of fabric graphic into
the horizontal track along the bottom
H1/H2 extrusion. Tuck the plastic edge
into the horizontal groove about 3” to
secure bottom two corners.
HangTen
Follow steps on the “Frame Setup
Instructions”. Alwas use white cotton
gloves provided when handling fabric
graphics to prevent soiling.
Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.
Graphics • 3
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Insert standoffs into the header horizontal
bars about 1 1/2” from each edge. Turn
clockwise to tighten.
Guide holes in header graphic onto
standoffs.
Fasten front side with two standoff caps. Your header assembly is complete.
Header Setup Instructions
Follow steps on the “Graphic & Light
Instructions”.
Lay out header parts. Attach Header1/Header2 horizontal
bars to either side of the H channel.
Tighten with hex wrench provided.
HangTen
Follow steps on the “Frame Setup
Instructions”. Remember to slide the
“H” channel above the track.
Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.
Accessories • 4
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Guide pedestal top underside onto
extrusion. Once, aligned push down
to engage it.
Align groove on the rear of the graphic
with the extrusion.
Tighten underside with hex wrench
provided.
Insert the top brass connector into the
groove. Tighten standoff cap to lock
brass connector into the extrusion.
Repeat on bottom of graphic.
Loosely attach standoff cap to a brass
connector on either side of the top hole
in the graphic.
Brass connector should be on the rear
of the panel. Repeat on bottom hole of
graphic.
Your product pedestal assembly is
complete.
Product Pedestal Setup Instructions
Follow steps on the “Graphic & Light
Instructions”.
Lay out pedestal parts. Tap insert out of foot from underside.
Slide extrusion into front slot with
channel facing outward. Tighten inside
lock hole with hex wrench provided.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.
Accessories • 5
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Tighten with hex wrench provided.
Slide keyboard arm into channel on the
underside of the shelf.
Attach monitor plate to cam lock and
tighten with hex wrench provided.
Lock keyboard arm into place on both
sides of channel. Tighten with hex wrench
provided.
Bolt bracket to rear of monitor. Lift monitor into position by sliding
vertical connector onto rectangular
framework until it clicks into the spring,
with wider side on the top.
Your small monitor mount and keyboard
shelf assembly are complete.
Guide keyboard arm through slot in
front of graphic panel into the extru-
sion behind it. Tighten with hex wrench
provided.
Up to 22” Small Monitor/Keyboard Shelf Setup Instructions
Follow steps on the “Graphic & Light
Instructions”.
Lay out monitor and keyboard parts. Guide cam lock through slot in front of
graphic panel into the extrusion
behind it.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.
Accessories • 6
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Follow steps on the “Graphic & Light
Instructions”. Four bracket corners should
align with holes in graphic.
Your assembled medium monitor mount
should look like this without the monitor
or graphic attached.
Attach metal frame to black mount.
Secure 4 outside points through slots in
graphic panel with washers and tighten
wingnuts.
Bolt two rails to rear of monitor. Lift monitor into position by sliding the
vertical bars on the back of the monitor
onto the monitor bracket.
23”-37” Medium Monitor Mount Setup Instructions
Lay out medium monitor mount parts. Insert the 1” standoffs into the monitor
extrusion. Slide the standoffs so they
are spaced apart to accomodate the
monitor mount.
Place black monitor mount over the
standoffs and tighten wingnuts.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with hex wrench always give it a 3/4 turn clockwise until tight.
Accessories • 7
Revised: 03/05/12 North America: 800.732.9395 Europe: +353.98.66011
Guide cam lock through slot in front of
graphic panel into the vertical extrusion
behind the graphic.
Tighten both sides with allen wrench
provided.
Insert horizontal extrusion to rear of
monitor top extrusion in the desired
position and tighten locks. Tighten with
allen wrench provided.
Bolt two vertical rails to rear of monitor.
Repeat 2nd horizontal attachment to
2nd vertical extrusion. Tighten with allen
wrench provided.
Connect monitor bracket to the cam
lock.
Your assembled large monitor mount
should look like this without the monitor
or graphic attached.
Lift monitor into position by sliding
vertical rails onto the monitor bracket.
38”-46” Large Monitor Mount Setup Instructions
Slide 2nd monitor extrusion into place and
lock at top and bottom with hex wrench
provided.
Follow steps on the “Graphic & Light
Instructions”.
Lay out large monitor parts.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with Allen Wrench always give it a 3/4 turn clockwise until tight.
Accessories • 8
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Fins attach to rear of frame. Insert the
loosened brass connectors into the
extrusion channel at the back of the
display.
Tighten standoff caps. Make sure the
brass connector is locked before letting
go of the graphic fin.
Your Origninal fin assembly is complete.
Original Fin Setup Instructions
Follow steps on the “Graphic & Light
Instructions”.
Lay out pieces on the ground. Insert brass fitting loosely onto rigid
graphic panel at the top and bottom
with cap.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.
Accessories • 9
Revised: 06/01/12 North America: 800.732.9395 Europe: +353.98.66011
Guide fin into the edge mount standoff. Hold the fin and tighten edge mount
standoff with hex wrench provided.
Repeat process with bottom fin.
Your Classic/Plus fin assembly is
complete.
Classic/Plus Fin Setup Instructions
Follow steps on the “Graphic & Light
Instructions”.
Lay out fin parts. Fins attach to sides of Classic/Plus
frame. Insert edge mount standoffs in
holes on the side of frame. Tighten with
hex wrench provided.
HangTen
Follow steps on the “Frame Setup
Instructions”.
Note: When tightening with hex wrench always give it a 1/2 turn clockwise until tight.
Accessories • 10
Inhaltsverzeichnis
Andere Nomadic Display Monitor Handbücher
