nor-tec SAM-e Bedienungsanleitung
SAM-e
Installation and
Operation Manual
Includes installation, operation
maintenance and troubleshooting
information for your SAM-e and Mini
SAM-e Short Absorption Manifold.
1507619-J| 29 September 2016
Important: Read and save these instructions. This guide to be left with equipment.
Thank you for choosing Nortec.
Proprietary Notice
This document and the information disclosed herein are proprietary data of NORTEC HUMIDITY LTD. Neither
this document nor the information contained herein shall be reproduced, used, or disclosed to others without
the written authorization of NORTEC HUMIDITY LTD., except to the extent required for installation or
maintenance of recipient’s equipment. All references to the Nortec name should be taken as referring to
NORTEC HUMIDITY LTD.
Liability Notice
Nortec does not accept any liability for installations of humidity equipment installed by unqualified personnel or
the use of parts/components/equipment that are not authorized or approved by Nortec.
Copyright Notice
Copyright 2014, NORTEC HUMIDITY LTD. All rights reserved.
INSTALLATION DATE (MM/DD/YYYY)
MODEL #
SERIAL #
Contents
2 Introduction
2 Location of Humidifier’s Manifold in an Air Conditioning System
4 Identify your Components
5 How to Use this Manual
7 SAM-e In-Duct
15 Installation in Vertical Duct
17 Mini SAM-e Installation Procedures
21 Plumbing
22 SAM-e with Pressure Steam
24 Mini SAM-e with Pressurized Steam
29 SAM-e with Atmospheric Steam
31 Mini SAM-e with Atmospheric Steam
33 Atmospheric Steam Lines
34 Plumbing
34 Atmospheric SAM-e Steam Lines
39 Length of Steam Line Runs
39 Material for Steam Lines
40 Atmospheric SAM-e Condensate Drainage
41 Steam Lines and Condensate Returns
45 Insulated SAM-e & Mini SAM-e
46 Insulation
49 SAM-e Insulation Retrofit
52 Mini SAM-e Insulation Retrofit
55 Troubleshooting, Maintenance, Spare Parts
1 | SAM-e Installation
CAUTION: Plumbing
Plumbing to be performed by a licensed plumber.
Drain water from humidifier can be very hot. Do not drain to public sink.
All plumbing work should be done according to local plumbing code.
CAUTION: Installation
Do not mount on hot surfaces.
Do not mount in area where freezing can occur.
Do not mount on vibrating surface.
Do not mount on floor.
The RH2 produces steam at atmospheric pressure no devices which could block
steam output should be connected to the steam outlet.
Steam lines must be installed so that no restriction can produce backpressure in
the humidifier.
CAUTION: Servicing
Disconnect main power before any servicing.
During and following operation of the humidifier, the steam and components in
contact with the steam such as the blower pack, steam lines, steam distributors,
and condensate lines can become hot and can burn if touched.
Nortec does not accept any liability for installations of humidity equipment
installed by unqualified personnel or the use of parts/components/equipment
that are not authorized or approved by Nortec.
SAM-e Installation | 2
Introduction
Receiving and Unpacking Equipment
Check packing slip to ensure ALL material has been delivered. Each humidifier may be shipped
in more than one box.
All material shortages are to be reported to NORTEC within 48 hours from receipt of goods.
NORTEC assumes no responsibility for any material shortages beyond this period.
Inspect boxes for damage and note on shipping waybill accordingly.
After unpacking, inspect equipment for damage. If damage is found, notify the shipper promptly.
All NORTEC products are shipped on an F.O.B. factory basis. Any and all damage, breakage, or loss
claims are to be made to the shipping company.
Location of Humidifier’s Manifold in an Air Conditioning System
Although SAM-e distribution systems are designed to provide drip-less humidification, several operating
factors related to steam supply may result in excess moisture or water collecting in
steam-tube pipe with the potential for water damage. To ensure protection against water damage, best
practice includes either a sealed section of duct or, preferably a drip-pan with drain installed underneath
each unit. In addition, to facilitate maintenance checks and inspections, an inspection cover, inspection
glass or service opening should be installed downstream.
For more information, see SAM-e Engineering Manual [1503529-X].
Notes
Absorption distance: the distance between the SAM-e and the first obstruction (coil, elbow, damper, etc.)
that steam may encounter. Traces of steam may pass the obstruction, but will not condense, leaving
obstructions dry. If any of the duct or air-handling unit (AHU) conditions are changed between design
and installation, calculated absorption distance may change. It is advisable to re-calculate absorption
distance to ensure that SAM-e operates as intended. If changes are required, please contact factory for
assistance.
3 | SAM-e Installation
Identify your Components
SAM-e Installation | 4
Identify your Optional Components
5 | SAM-e Installation
How to Use this Manual
SAM-e - In Duct
Section 2
Follow steps 1-9
SAM-e - Vertical Duct Installation
Section 4
Follow steps 1-8B
Then refer to Section 3.
mini SAM-e
Section 5
Follow steps 1-5
SAM-e Installation | 6
Plumbing
Section 6
6A - SAM-e Pressure Steam
6B - mini SAM-e Pressure Steam
6C - SAM-e Atmospheric Steam
6D - mini SAM-e Atmospheric Steam
Steam Lines
Section 7
SAM-e Insulation
Section 8
8A - SAM-e Retrofit
8B - mini SAM-e Retrofit
Troubleshooting, Spare Parts & Warranty
Section 9
7 | Installation
SAM-e In-Duct
Andere Handbücher für SAM-e
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere nor-tec Klimaanlage Handbücher
