Nordcap MG 185 Bedienungsanleitung

GB Reversible door

DE Wendbare Tür

DK Vendbar dør

FR Porte réversible

IT Porta reversible

Türanschlagwechsel - Aufbauanleitung

Glastürkühlschrank

MG 185

Art. 477850185

2016-09

Reversible door

Follow the instructions carefully

NOTE: Before you start the unit needs to be disconnected from the main grid.

We recommend that the change of door is done by a technician (we recommend two persons)

Helping material:

4 mm Allen key;

Flat-headed screwdriver

Torx 20 (TX20) screwdriver

2. Place the appliance on its back (prefera-

bly on a soft foundation)

1. Open the door, unscrew the two screws

xing the bottom cover (Torx20). Do not

remove the cover yet.

3. Loosen the upper hinge and remove it ( 4

mm Allen key)

4. Dismount the bottom cover (the build-

in snap function in each side can be

unsnapped with the at-headed screw-

driver).

5. Place the bottom cover with glass front

down, on an additional support, so the

wires are not stretched.

6. The door LED wires have to be dismount-

ed from the connector on the bottom

cover (pure black & black / white stripe

wires). Push the top release down to free

the wire ends. (Note: the pure black wire

is + and corresponds to the red wire on

opposite side. The black / white stripe

wire is 0 (neutral) and corresponds to

the black wire on the opposite side – this

is important when the wires are to be

mounted later)

7. To reverse the bottom glass, the brackets

need to be removed. Loosen the screw

and the bracket incl. screw and bolt

slides of the plastic prole.

NOTE: Now the glass is loose.

10. Unscrew the lock pin (using the at-

headed screwdriver) and remove it.

8. Lift the bottom sheet metal part and turn

the glass so the lock hole ts the other

ends round Ø hole concentric. Place the

sheet metal part on the glass again, and

mount the brackets onto the plastic pro-

le in each end again. Don’t over tighten

the screws.

Note: The nut has to t into the centre

groove.

11. Pull up the lock cylinder and ret both

lock cylinder and lock pin in opposite

side.

9. The door has to be moved up from the

hinge.

13. Dismount the bottom hinge pin and t it

on the opposite side.

Note: The bush must also be moved.

12. Pull the LED wires gently out of the bot-

tom hinge pin.

14. Turn the door, so the glass side is down

(Note: Place something between the

glass and the other surface (cabinet) so

scratch are minimized).

Then loosen the gasket on the low end

of the door by pulling.

15. Pull the LED wires up and out.

16. Replace the wires into the plastic

groove and lead them to the other side.

17. Push the wires through the oblong hole

and through the new hinge hole.This

can be a bit tricky so try to mount only

one wire rst

18. Then tape the second wire end to

the rst wire and pull them both fully

through (remove tape subsequently).

19. Make sure the wires are tted into the

plastic groove and mount the gasket. It’s

important to check that the sealing strip

provides a tight seal all the way round.

If it does not, carefully heat the strip all

the way round using a hair dryer. Then

ease the strip slightly outwards so that

it forms a tight seal against the cabinet.

Be careful not to heat the strip so much

that it melts!

21. Pull the wire through the bushing before

mounting it into the door hinge hole.

20. Dismount the door hinge bushing and

mount it on opposide side.

22. Reverse the door again and displace it

a little on the cabinet proportion to the

botton hinge.

23. Pull the two wires through the bottom

hinge pin....

24. … and through the wire hole in the

plastic column.

25. Remount the wires (se under # 6) and

make sure that they are rmly secured.

26. Pusch the door back in place over the

hinge pin and pull the wires simultane-

ously so the wire do not get stuck.

27. Dismount the top door bushing and

mount it on opposite side.

28. Dismount the plastic caps on the top of

the cabinet and mount them on opposite

side.

29. Make sure that the door is aligned with

the cabinet before mounting the top

hinge.

30. Remount the bottom front cover. Place

the unit vertically again and mount the

tow screws (see under # 1).

Note: Important: Wait approx. ½ hour

before connecting the unit to the main

grid.

Note: If the door LEDs don’t give out light

but the top LED in the cabinet is shin-

ing, it’s most likely that the wires are not

mounted correctly into the connector.

(See under # 6 & 25)

Wendbare Tür

Folgen Sie sorgfältig der Anleitung

Hinweis: Bevor Sie starten das Gerät vom Stromnetz trennen.

Wir empfehlen den Wechsel des Türanschlages vom einem Techniker ausführen zu lassen (wir

empfehlen zwei Personen)

Hilfsmaterial:

4 mm Inbusschlüssel

Schlitzschrauben dreher

Torx 20 (TX20) Schraubendreher

2. Legen Sie das Gerät auf die Rückseite

(am besten auf einer weichen Unterlage)

1. Tür ö󰀨nen und die beiden Schrauben für

die untere Blende entfernen. (Torx 20)

Die Blende jetzt noch nicht entfernen.

3. Lösen und entfernen Sie das obere

Scharnier (4 mm Inbus)

Andere Handbücher für MG 185

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Nordcap Kühlschrank Handbücher

Nordcap

Nordcap Alpeninox KU 400 W Bedienungsanleitung

Nordcap

Nordcap V160 Semiprofessional Series Montageanleitung

Nordcap

Nordcap TK 400 CHR Bedienungsanleitung

Nordcap

Nordcap KU 710 GL-Plus Bedienungsanleitung

Nordcap

Nordcap VAR-PM13 Bedienungsanleitung

Nordcap

Nordcap M180 Bedienungsanleitung

Nordcap

Nordcap VAR-PC12 Bedienungsanleitung

Nordcap

Nordcap UHD 200-P BLACK Bedienungsanleitung

Nordcap

Nordcap 700l Refrigerator Bedienungsanleitung

Nordcap

Nordcap KU 1000 G-SD Bedienungsanleitung

Nordcap

Nordcap KU 175 G-SP Bedienungsanleitung

Nordcap

Nordcap COOL-LINE SL 10 Bedienungsanleitung

Nordcap

Nordcap Alpeninox TK 400 W Bedienungsanleitung

Nordcap

Nordcap TM32 Bedienungsanleitung

Nordcap

Nordcap COOL-LINE ENTRY SKF 2/3 GN Kurzanleitung

Nordcap

Nordcap M5 Bedienungsanleitung

Nordcap

Nordcap TM 42-V Bedienungsanleitung

Nordcap

Nordcap KU 400 CHR Bedienungsanleitung

Nordcap

Nordcap ENTRY Kurzanleitung

Nordcap

Nordcap KU 407 Bedienungsanleitung

Nordcap

Nordcap LINUS 100 Kurzanleitung

Nordcap

Nordcap SCU 1425 Bedienungsanleitung

Nordcap

Nordcap MG 185 Bedienungsanleitung

Nordcap

Nordcap Alpeninox KU 400-G W Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung