Nordson HSS Bedienungsanleitung

Equipment required:

a Filled cartridges (Ratio-Pak®cartridges shown)

b HSS static mixer spray nozzle and air regulator kit

c HSS pneumatic spray gun

Note: To use Film-Pak®collapsible cartridges,

order a gun with built-in retainers or use

removable retainers with an existing gun.

If recommended by the product manufacturer,

pre-heat the cartridge for 1–2 hours at 32–38° C

(90–100°F). Do not exceed 49° C (120° F), as this

will affect the integrity of the cartridge.

Important: Consult with the product manufacturer

to determine whether shaking is required. If

shaking is required, gently agitate / shake new or

partially used cartridges for at least two minutes

prior to application.

Remove the retaining nut, compression disc, and

end cap(s) from the cartridge outlet.

High Solid Spray (HSS) System

Instructions

100°

90°

38°

32°

C F

If required, insert a ow restrictor.

Note: Some products require the use of a ow

restrictor to equalize material ow. Flow restrictors

are ordered separately. Contact your Nordson EFD

representative for the proper ow restrictor and for

installation assistance.

Seat an HSS static mixer spray nozzle on the

cartridge outlet, ensuring that the bell housing sits

ush on the tip of the outlet. If required, install a

retaining nut.

Note: Integral nut mixers do not require a retaining

nut; bell mixers do require a retaining nut.

End cap

Retaining nut

1 2

3 4

5 6

a b

High Solid Spray (HSS) System Instructions

For Nordson EFD sales and service in over

40 countries, contact Nordson EFD or go to

www.nordsonefd.com.

800-556-3484; +1-401-431-7000

[email protected]

Attach the air line of the HSS air regulator kit to the

HSS static mixer spray nozzle.

On the HSS regulator, place the ball valve lever (a)

in the closed position; then connect the plant air

supply (b) to the HSS regulator.

Point the gun up (a) and slowly dispense material

into the static mixer. Then dispense the rst 15 cm

(6") of unmixed material into a waste container (b).

Perform this process for each new or partially used

cartridge.

Important: Before increasing the uid pressure, verify that both material

components are traveling equally through the mixer. As needed, dispense

unmixed material into a waste container.

With the ball valve lever (a) in the closed position, set the HSS regulator (b) to

1.7bar(25psi); then slowly move the ball valve lever to the open position to

supply the spray nozzle with atomizing air. Adjust the HSS regulator and ball

valve lever until the desired operational settings are achieved.

Depending on the material, the material temperature, and the desired nish,

adjust the uid pressure regulator knob on the gun (c) as needed.

If applicable, hand-tighten the retaining nut

securely on the cartridge outlet threads (do not

over-tighten).

Insert the cartridge (or cartridge / retainer — not

shown) in the dispense gun, referring to the

applicable dispense gun instructions as needed.

7 8

9 10

a b

Point the cartridge up

Fluid pressure regulator

knob on the dispense gun

On the dispense gun, turn the uid pressure

regulator knob counterclockwise until it will no

longer turn; then turn the knob 1–2 rotations

clockwise.

Note: Steps 11–12 purge air from the cartridge.

Fluid pressure adjustmentHSS regulator air pressure

adjustment

Ball valve

lever

Dispense unmixed material

Andere Nordson Spritzpistole Handbücher

Nordson

Nordson A7A Bedienungsanleitung

Nordson

Nordson A7A Referenzhandbuch

Nordson

Nordson HORIZON 200 Bedienungsanleitung

Nordson

Nordson Encore HD Referenzhandbuch

Nordson

Nordson Trilogy Bedienungsanleitung

Nordson

Nordson AN-8 Plus Referenzhandbuch

Nordson

Nordson Tribomatic II Referenzhandbuch

Nordson

Nordson Trilogy Bedienungsanleitung

Nordson

Nordson Sure Coat Series Referenzhandbuch

Nordson

Nordson MEG II Referenzhandbuch

Nordson

Nordson Encore 1096694A Bedienungsanleitung

Nordson

Nordson Kinetix 334593-04 Referenzhandbuch

Nordson

Nordson Encore PE Bedienungsanleitung

Nordson

Nordson Encore LT Automatic Referenzhandbuch

Nordson

Nordson Encore Series Referenzhandbuch

Nordson

Nordson Versa-Spray II Referenzhandbuch

Nordson

Nordson Encore LT Bedienungsanleitung

Nordson

Nordson Trilogy AS Bedienungsanleitung

Nordson

Nordson A7AA Referenzhandbuch

Nordson

Nordson Tribomatic II Referenzhandbuch

Nordson

Nordson Maverick Bedienungsanleitung

Nordson

Nordson ColorMax Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Nordson

Nordson Encore XL Powder Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

Graco

Graco HydroShield WMBH00 Stücklistenhandbuch

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung