North American Tool 7560 Bedienungsanleitung

8807560 05/13

18 GAUGE FLOORING STAPLER

SPECIFICATIONS

Minimum Operating Pressure:

60 PSI

Maximum Operating Pressure:

100 PSI

Stapler Size: 18 gauge

Staple Length: 3/8 in. - 1/4”

Magazine Capacity: 100 nails

Air Inlet: 1/4 in.

Air Consumption: 1 CFM

CAUTION:

FOR YOUR OWN SAFETY READ

INSTRUCTION MANUAL

COMPLETELY AND

CAREFULLY BEFORE

OPERATING THIS FLOORING

STAPLER.

Any failures made in following

the safety regulations and

instructions may result in an

electric shock, fire and/or

serious injury.

SAFETY INSTRUCTIONS

•KEEP WORK AREA CLEAN.

Cluttered areas invite injuries.

• DON’T ALLOW CHILDREN

AROUND THE WORK AREA.

Do not let children handle the

tool.

• DO NOT OPERATE THIS

TOOL IF UNDER THE

INFLUENCE OF ALCOHOL OR

DRUGS. Read the warning

labels on prescriptions to

determine if your judgment or

reflexes are impaired while

taking drugs. If there is any

doubt, do not attempt to

operate.

• USE SAFETY GLASSES.

Safety glasses should conform

to ANSI z87.1 specifications.

Safety glasses should be worn

against flying to debris from the

front and side. Safety glasses

should be worn when loading,

operating, unloading, or

servicing the tool.

• USE EAR PROTECTION. The

working area may be exposed to

high noise levels that can lead

to hearing damage.

• NEVER USE OXYGEN,

COMBUSTIBLE GASES,

BOTTLED GASES, OR HIGH

Models: 7560

For Customer Service, please call 1-800-348-5004 or

email feedback@natitools.com

CALIFORNIA PROPOSITION 65

WARNING: You can create dust

when you cut, sand, drill or grind

materials such as wood, paint,

metal, concrete, cement, or other

masonry. This dust often contains

chemicals known to cause cancer,

birth defects, or other

reproductive harm. Wear

protective gear.

WARNING: This product or its

power cord may contain

chemicals, including lead, known

to the State of California to cause

cancer and birth defects or other

reproductive harm. Wash hands

after handling.

Important!

When using equipment, a few safety

precautions must be observed to

avoid injuries and damage. Please

read the complete operating manual

with due care. Keep this manual in a

safe place, so that the information is

available at all times. If you give the

equipment to any other person, give

them these operating instructions as

well. We accept no liability for

damage or accidents which arise due

to non-observance of these

instructions and the safety

information herein.

PRESSURE COMPRESSED GAS

AS A POWER SOURCE FOR

THIS TOOL. The tool may explode

and cause serious injury.

• DRESS SAFELY. Protective

gloves and nonskid footwear or

safety shoes are recommended

when working with and operating

this tool. Do not wear loose

clothing or jewelry. They can get

caught in moving parts. Also, wear

a protective hair covering to

prevent long hair from getting

caught in the tool.

• DO NOT FIRE INTO HARD

MATERIALS. Do not attempt to

shoot toward hard or brittle

material such as concrete, steel, or

tile.

• KEEP PROPER FOOTING.

When operating this tool, keep the

proper footing and balance to

avoid damage resulting from losing

balance.

• CHECK DAMAGED PARTS.

Before using this tool, carefully

check if there are any loose or

damaged parts.

• REPLACE PARTS AND

ACCESSORIES. Only allow the

use of the same replacement parts

while servicing.

• KEEP ALERT. Watch what you

are doing. Use common sense. Do

not operate any tool when you are

tired.

• STORE THE TOOL. When not in

use, the tool should be cleaned,

fully assembled and then, stored in

a dry location to reduce rust. For

safety, keep out of the reach of

children.

• OUTDOOR EXTENSION

CORDS. When an air compressor

is used outdoors, use only rounded

jacket extension cords intended for

SETTING

Your air tool is fully assembled

when you receive it. Before

using it, attach the air line and

desired air system accessories.

See Figure 1 for the

recommended accessories and

connection order. Be sure the

air hose is depressurized when

installing or removing adapters

to the air line.

outside use. See manufacturer’s

manual for the AWG required for

the compressor’s amperage draw.

• PAY ATTENTION TO THE AIR

HOSE AND THEIR

CONNECTIONS. Do not trip over

hoses. Make sure all connections

are tight.

•AFTER LOADING THE

FASTENERS. Never point the tool

at yourself or bystanders.

• USE THE CORRECT AIR

CONNECTOR. The connector on

the tool must no hold pressure

when the air supply is

disconnected. If the wrong fitting is

used, the tool can be charged with

air after being disconnected and

still able to drive a fastener.

• CONNECTING THE AIR. When

connecting the air, the tool may

possibly fire the fasteners as soon

as you plug it into the air hose.

Therefore, remove all the fasteners

before connecting it to the air

supply.

•DO NOT DEPRESS THE

TRIGGER WHEN LOADING.

• CLEARING A JAM. If the

fasteners are jammed, disconnect

the tool from the air and remove

the jammed fasteners.

WARNING: The warnings,

cautions, and instructions

explained in thisinstruction

manual cannot cover all

possible conditions and

situations that may occur. It

must be understood by the

operator that COMMON SENSE

AND CAUTION ARE FACTORS

WHICH CANNOT BE BUILT INTO

THIS PRODUCT, BUT MUST BE

SUPPLIED BY THE USER.

CONNECTING THE TOOL TO

AN AIR SUPPLY

1. Determine if the tool needs

oil and, if necessary, place two

drops of oil in the air plug as

shown in figure 2.

feedback@natitools.com

If you are using an automatic in-

line oiler, check and add oil if

necessary

2. Turn the compressor on and

set the regulator to the proper

pressure for the size and type of

fastener being used.

3. Connect the tool to the air

supply (see Figure 1 for

recommendations).

LOADING THE FASTENERS

1. Depress the lock to release

the movable magazine and pull

the magazine out fully as shown

in Figure 3.

2. Place a full clip of the

specified type and size of

fasteners on the fixed

magazine, up to 100 fasteners

may be loaded in the magazine.

3. Push the movable magazine

assembly forward until it locks.

OPERATING THE TOOL

Test the driving depth in a

sample piece of wood before

using. If the fasteners are being

driven too far or not far enough,

adjust the regulator to provide

less air pressure or more air

pressure.

1. Connect the tool to the air

supply. Make sure the air

pressure is in correct range

denoted in the specifications.

2. Load the fasteners.

3. Hold the body and press the

drive guide to the work surface.

Be sure the tool is straight and

the gently depress the trigger to

drive the fastener.

4. Lift the tool off the work

surface.

REGULAR MAINTENANCE

1. Frequent, but not excessive,

lubrication is required for best

performance. Oil added through

the airline connection will

lubricate internal parts. An

automatic inline oiler is

recommended, but oil may be

added manually before every

operation or after about 1 hour of

continuous use. (see Figure 1)

Only a few drops of oil at a time

are necessary. Too much oil will

collect inside the tool and be

blown out during the exhaust

cycle. ONLY USE PNEUMATIC

TOOL OIL. Do not use detergent

oil or additives, as these

lubricants will cause accelerated

wear to the seal in the tool.

2. Use a small amount of oil on all

moving surfaces and pivots.

3. Dirt and water in the air supply

are major causes of pneumatic tool

wear. Use a filter/oiler for better

performance and longer life. The

filter must have adequate flow

capacity for the specific application.

Consult the manufacturer’s

instructions for proper maintenance

of your filter.

4. Keep tools clean for better and

safer performance. Use

nonflammable cleaning solutions

only if necessary. (CAUTION: Such

solutions may damage O-Ring and

other tool parts) DO NOT SOAK.

feedback@natitools.com

Symptom Possible Cause(s) Corrective Action

O-Ring in trigger valve is damaged Check and replace O-Ring.

Trigger valve head is damaged Check and replace trigger valve head.

Trigger valve stem, seal or O-Ring is damaged.

Check and replace trigger valve stem, seal, or O-

Ring

Air leaking between body and

drive guide

Damaged bumper Check and replace bumper

Screw loose Tighten screws

Damaged gasket Check and replace gasket

Worn bumper Replace bumper

Air pressure is too high Adjust air pressure

Insufficient oil Lubricate as instructed

Insufficient air supply Check air supply

Broken spring in cylinder cap Replace spring

Exhaust port in cylinder cap is blocked Replace damaged internal parts.

Worn bumper or damaged spring Replace bumper or pusher spring

Dirt in drive guide Clean drive channel of front plate

Inadequate airflow to tool Check hose and compressor fittings

Worn or dry O-Ring on piston Replace O-Ring or lubricate

Cylinder cap seal leaking Replace seal

Joint guider is worn Replace joint guide

fasteners are wrong size or damaged Use the recommended and undamaged fasteners

Magazine or front plate screws are loose Tighten screws

Blade in piston assembly is damaged Replace piston assembly

Worn blade in piston assembly Replace piston assembly

Lack of power Adjust to adequate air pressure

Slow cycling and loss of power

Check cylinder cap spring for broken coils or reduced

length.

Check if exhaust port of cylinder cap is restricted

Fasteners are jammed

Tool will not drive down tight

Air leak near top of tool or in

trigger area

Air leaking between body and

cylinder cap

Blade driving fastener too deeply

Runs slowly or has lost power

Tool skips a fastener

DO NOT RETURN TO STORE

North American Tool (NAT) Industries makes every effort to ensure that this product meets high

quality and durability standards. NAT warrants to the original retail consumer a 1-year limited warranty

from the date the product was purchased at retail and each product is free from defects in materials.

Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or

accidents, repairs or alterations, or a lack of maintenance. NAT shall in no event be liable for death,

injuries to persons or property, or for incidental, special or consequential damages arising from the

use of our products. To receive service under warranty, the original manufacturer part must be

returned for examination by an authorized service center. Shipping and handling charges may apply. If

a defect is found, NAT will either repair or replace the product at its discretion.

feedback@natitools.com

North American Tool Industries (NATI) makes every effort to ensure that this product meets high

quality and durability standards. NATI warrants to the original retail consumer a 1-year limited

warranty from the date the product was purchased at retail and each product is free from defects in

materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence,

or accidents, repairs or alterations, or a lack of maintenance. NATI shall in no event be liable for

death, injuries to persons or property, or for incidental, special, or consequential damages arising from

the use of our products. To receive service under warranty, the original manufacturer part must be

returned for examination by an authorized service center. Shipping and handling charges may apply. If

a defect is found, NATI will either repair or replace the product at its discretion.

DO NOT RETURN TO STORE

For Customer Service:

Email: feedback@natitools.com or Call 1-800-348-5004

8807560 05/13

18 GAUGE FLOORING STAPLER

Model: 7560

For Customer Service, please call 1-800-348-5004 or

email feedback@natitools.com

feedback@natitools.com

No. Description No. Description

1 Screw m4*10 37 Washer

2 Bushing 38 Trigger Assembly

3 Exhaust Cover 39 Trigger Pin

4 Washer 40 Screw M4*16

5 Screw M5*20 41 Washer

6 Spring Washer 5 42 Oblique Block

7 Cylinder Cap 43 Screw M5*25

8 Gasket 43a Screw M5*8

8a Spring 44 Cover Plate

9Valve Seat 45 Limited Blick

10 O-Ring 15.7*2 46 Slide Plate

11 O-Ring 38.8*3 47 Bushing

12 Valve 48 Screw M4*16(12.9)

13 O-Ring 33.5*3.5 49 Drive Guide

14 Stopped Washer 50 Spring Pin2.5*11

15 Collar 51 Movable Magazine

16 O-Ring 50.5*2.5 52 Feeder Shoe

17 O-Ring 28.3*2.5 53 Spring

18 Piston Assembly 54 Fixed Magazine

19 Cylinder 55 Nut M4

20 O-Ring 36.3*2.5 56 Magazine Plate

21 O-Ring 35.3*2.5 57 Screw M4*8

22 Bumper 58 Screw M4*14

23 Body 59 Bushing

24 Joint Guide 60 Spring

25 Safe Guide 61 Lock

26 Spring 62 Joint Guide

27 Safe Bracket 63 Pin 1.2*10

28 Spring Pin 3*26 64 Stopped Screw

29 Seal 65 Support

30 Trigger Valve Head 66 Nut M5

31 O-Ring 15*1.9 67 Screw M5*18

32 Trigger Valve Guide 68 Soft Grip Sleeve

33 O-Ring 5.5*1.5 69 Gasket

34 Spring 70 End Cap

Inhaltsverzeichnis

Andere North American Tool Elektrowerkzeuge Handbücher

North American Tool

North American Tool 9387 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch