Northern Industrial Flux Core 125 Bedienungsanleitung

QUICK SET-UP GUIDE

This guide is intended to provide quick instructions on the set-up of your new welder.

Please take time to review the operator’s manual prior to operating this unit.

Flux Core 125

Item #628575

For more help visit www.ntwelderhelp.com

Or Call 1-877-304-0294

INSTALLING A 4” SPOOL OF WIRE

DRIVE ROOL - USE KNURLED GROOVE

56FEED WIRE - OPEN TENSION ARM

910

FEED WIRE - REMOVE GUN TIP & NOZZLE FEED WIRE - PULL TRIGGER TO FEED WIRE

Remove wing nut, washer and black bushing. Slide on spool so

wire feeds off the bottom of spool. Reinstall bushing, washer and

wing nut. See Step 12 to adjust wire spool tension.

Always make certain that the knurled groove is in line with the

wire when installed on drive shaft.

Open the drive roll tension arm on the wire feeder.

To finish feeding the wire through the gun, you will need to

remove the gun nozzle and tip.

Stretch out the gun. Turn on input power and pull the trigger to

feed the wire through the gun. Stop when the wire pushes through

the end of the gun.

Tighten

Clockwise

Knurled Groove

INSTALLING UNIT HANDLE

The handle for this unit is supplied along with the hardware to

secure it. Locate the handle and hardware and install as shown

Drive Roll

Tension Arm

INSTALLING A 8” SPOOL OF WIRE

3DRIVE ROLL REMOVAL

FEED WIRE - THREAD WIRE FEED WIRE - CLOSE TENSION ARM

11 12

FEED WIRE - REINSTALL TIP AND NOZZLE

Remove wing nut, washer and black bushing. Slide on spool

adapter. Reinstall bushing, washer and wing nut. Slide on 8”

spool of wire. Knob on spool adapter slides into hole on side of

8” spool of wire. See Step 12 to adjust wire spool tension.

This unit comes with the drive roll in place. If removal is needed,

turn drive roll cap counter clockwise 1/4 turn. Pull out to remove.

The drive roll will slide of drive shaft.

Feed the loose end of the wire through the Inlet Guide Tube, past

the drive roll and into the back of the MIG Gun. Keep tension on

the wire to prevent unspooling on the spool.

Close the drive roll tension arm. Apply tension to the wire by

turning the wing nut clockwise on the Drive Roll Tension Adjust-

ment. Do not overtighten. See Step 13.

Slide the correct size contact tip for the wire size you are using

over the end of the wire and tighten clockwise to secure. Thread

on nozzle and clip any excess wire.

Drive

Roll

8 In.

Spool

Adapter

Drive

Roll

Cap

Knob

Tension

Adjustment

ADJUSTING SPOOL TENSION

Adjust the wing nut in the center of the spool to adjust spool ten-

sion. A small amount of slack should be in the weld wire when

wire feeding stops. Too much tension will cause poor feeding.

Too little tension will cause the wire on the spool to uncoil.

Tighten

Clockwise

13 14

ADJUSTING DRIVE ROLL TENSION SETTING FRONT PANEL CONTROLS

Test drive roll tension by feeding wire into a gloved hand from

about 4 inches away. Loosen drive roll tension to apply little

pressure. Slowly increase drive roll tension until the wire coils up

in your hand without slipping in the drive rolls.

On the wire compartment access panel is a set-up guide. Find the

type of material being welded and the size of wire you are using.

Slide over to the thickness of the thinnest material you are weld-

ing. Set the voltage and wire feed speed on the front of the unit.

15 ATTACH GROUND CABLE TO WORK

Attach the ground cable to the welding table or work-piece.

Wire Feed Control

Voltage

Control

Andere Handbücher für Flux Core 125

Dieses Handbuch passt für folgende Modelle

Andere Northern Industrial Schweißsystem Handbücher

Northern Industrial

Northern Industrial ARC 200 Bedienungsanleitung

Northern Industrial

Northern Industrial MIG 130 Bedienungsanleitung

Northern Industrial

Northern Industrial ST 80 i Bedienungsanleitung

Northern Industrial

Northern Industrial Flux Core 125 Bedienungsanleitung

Northern Industrial

Northern Industrial Flux Core 125 Bedienungsanleitung

Northern Industrial

Northern Industrial MIG 135 Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung

Lincoln Electric

Lincoln Electric POWER WAVE I400 Bedienungsanleitung