Norton clipper CDR 353 Bedienungsanleitung
Kit CDR 353 + NBM 351
OPERATING INSTRUCTIONS
Translation of the original instructions
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
2
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
3
The undersigned manufacturer:
SAINT - GOBAIN ABRASIVES S.A.
190, BD. J. F. KENNEDY
L-4930 BASCHARAGE
Declares that this product:
« Drill Rigs »: Kit CDR 353 + NBM 351 Code : 70184694707
is in conformity with the following Directives :
"MACHINES" 2006/42/CE
"LOW VOLTAGE" 2006/95/CE
"ELECTROMAGNETIC COMPATIBILITY" 2004/108/CE
"NOISE" 2000/14/CE
And the European standard:
EN 12348 –Core drilling machines on stand –Safety
Valid for machines as of serial number:
150500000
Storage site for the technical documents:
Saint-Gobain Abrasives 190, Bd. J. F. Kennedy 4930 BASCHARAGE, LUXEMBOURG
This declaration of conformity loses its validity when the product is converted or modified without
agreement.
Bascharage, Luxembourg, 19/05/2015.
Olivier Plenert, executive officer.
Declaration of conformity
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
4
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
5
Kit CDR 353 + NBM 351 :
OPERATING INSTRUCTIONS
1BASIC SAFETY INSTRUCTIONS 6
1.1 Symbols 6
1.2 Machine plate 7
1.3 Safety instructions for particular operating phases 8
2MACHINE DESCRIPTION 9
2.1 Short description 9
2.2 Purpose of use 9
2.3 Layout 9
2.4 Technical Data 10
2.5 Statement regarding the vibration emission 11
2.6 Statement regarding noise emission 12
3ASSEMBLY AND COMMISSIONING 13
3.1 Assembling the motor on the rig 13
3.2 Tool assembly 13
3.3 Electrical connections 13
3.4 Changing motor speed 14
3.5 Water cooling 14
4TRANSPORT AND STORING 15
4.1 Securing for transport 15
4.2 Transport procedure 15
4.3 Long period of inactivity 15
5OPERATING THE MACHINE 16
5.1 Site of work 16
5.2 Drilling method 16
6MAINTENANCE AND SERVICING 20
7FAULTS: CAUSES AND CURES 21
7.1 Fault-finding procedures 21
7.2 Trouble-shooting guide 21
7.3 Customer service 22
8APPENDIX 24
Ideal rotation speed of the core bit in relation to the hole diameter 24
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
6
1 BASIC SAFETY INSTRUCTIONS
The core drill rig CDR 353 is exclusively designed for the drilling of construction products
mainly within a Construction Site.
Uses other than the manufacturer's instructions shall be considered as contravening the
regulations. The manufacturer shall not be held responsible for any resulting damage. Any
risk shall be borne entirely by the user. Observing the operating instructions and compliance
with inspection and servicing requirements shall also be considered as included under use in
accordance with the regulations.
1.1 Symbols
Important warnings and pieces of advice are indicated on the machine using symbols. The
following symbols are used on the machine:
Read operator’s instructions
Ear protection must be worn
Hand protection must be worn
Eye protection shall be worn
Airway protection must be worn
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
7
1.2 Machine plate
Important data can be found on the following plate located on the machine:
Machine Model
Machine Code
Weight
Year of production
Machine type
Serial number
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
8
1.3 Safety instructions for particular operating phases
Before commencing work
Before commencing work, make yourself familiar with the working environment at the
place of use. The working environment includes: obstacles in the area of work and
manoeuvre, the firmness of the floor, necessary protection at the site relating to public
thoroughfares and the availability of help in the event of accidents.
Immediately remove damaged or badly worn core bits, as they endanger the operator
whilst rotating.
Only fit NORTON diamond core bits to the machine! The use of other tools can damage
the machine!
Read the core bits’ specifications carefully to choose the adequate tool to your
application.
Make sure the handle of the machine is free from oil or grease.
Attention is drawn to the use of BS2092 safety goggles in conformity with specified
Processes No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1.
Make sure that no mounting tool is left on the machine before starting it.
Electrical powered machine
Make sure that the electrical supply of the machine is equipped with a grounded
protective connector. If you have doubts, let a qualified electrician check the electrical
system.
Never pull the machine by the cable to transport it or to separate it from the electrical
supply.
Avoid any contact between the cable and extension cable and heat sources, oil, and
sharp edges.
Always check the cable before commencing work. If it is damaged, let a qualified
electrician replace it.
Switch the machine off, and isolate it from the main electrical supply before attempting
any maintenance or repair on the machine
In the event of the machine breaking down or stopping for no apparent reason, switch off
the main electricity supply. Only a qualified electrician is allowed to investigate the
trouble and remedy the fault.
Always isolate the machine from the electrical supply when not in use.
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
9
2 MACHINE DESCRIPTION
Any modification, which could lead to a change in the original characteristics of the machine,
may be done only by Saint-Gobain Abrasives who shall confirm that the machine is still in
conformity with the safety regulations.
2.1 Short description
The CDR 353 core drill rig is designed for durability and high performance for onsite wet and
dry drilling operations of a wide range of masonry and natural stone products. As with all
other NORTON products, the operator will immediately appreciate the attention given to
detail and quality of materials used in construction. The machine and its component parts
are assembled to high standards assuring long life and minimum maintenance.
2.2 Purpose of use
The machine is designed for drilling a large range of building materials. It is not designed for
drilling wood or metals, except steel reinforcing securely embedded in concrete.
2.3 Layout
There are two main parts on the core drilling rig CDR 353: the motor and the rig itself.
The rig is made of sectional aluminium, which reduces the weight of the machine allowing
easy transportation. The base ensures stability of the rig, and allows two ways of fixing the
rig: using a vacuum pump or fixing anchors. The rig is equipped with a quick fixing plate, so
the motor can be fitted or removed quickly from the rig. Three different types of electric
motor are available on the CDR 353, offering excellent quality of drilling and extended life
duration. Every motor is equipped with a P.R.C.D. (Portable Residual Current Device). This
circuit breaker protects the motor from an electrical overload. The P.R.C.D. is a circuit
breaker and not a switch. Always stop the motor using its switch and not the P.R.C.D.
VERS.2015.05.19 Kit CDR 353 + NBM 351_MAN_EN
10
2.4 Technical Data
Rig
Max. drill bit diameter
350mm
Movement
642mm
Tilting
0 to 45°
Weight of the rig
23.4 kg
Dimensions (Length x width x
height)
550x375x1080 mm
You can find the code number on the machine plate. If you bought a complete kit, your
machine is composed of a column with combined base, a motor and a motor assembling
plate. These are the characteristics of the motor:
Motor 310405045
Motor
NBM 351
Power
3,3 kW
Motor protection
P.R.C.D. 10 mA
Rotation speeds
230/510/730min-1
Total weight
12 Kg
Range of core bit diameter
50-400mm
Connector
1¼’’ UNC male
Kit Rig + Motor
Weight
35.4 kg
Dimensions (Length x width x height)
685x375x1180mm
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Norton Bohren Handbücher
