Notifier NFX-WS series Bedienungsanleitung

MODELS

NFX-WS-** = Sounder Non Isolation

NFXI-WS-** = Sounder Isolation

NFX-WSF-** = Sounder Strobe Non Isolation

NFXI-WSF-** = Sounder Strobe Isolation

NFX-WF-** = Strobe Non Isolation

NFXI-WF-** = Strobe Isolation

** = Denotes colour

GENERAL

The range of intelligent AV devices are designed to be connected to analogue addressable re

alarm systems.

These devices must only be connected to control panels that use a compatible proprietary

analogue addressable communication protocol.

These devices receive their power from the loop, and can be controlled via the communication

protocol(s).

The sounders have three volume levels and 32 tone sets. Models (NFXI-WS-**, NFXI-WSF-**,

NFXI-WF-**) containing the character ‘I’ prior to the Customer ID code include in built isolation

providing short circuit protection of the loop.

Up to 159 addresses are available. (consult the panel instructions to conrm compatibility)

These are selected via the two rotary switches. The ‘tens’ digits go from 0 to 15 and the ‘units’

from 0 to 9.

Note: if the control equipment is not capable of taking more than 99 module addresses, a fault

condition will be generated for every address over 99.

SPECIFICATIONS

Operating temperature range -25 to +70oC

Relative humidity up to 93% (± 3%) - non condensing

Terminal Size 2.5mm2- maximum

For isolator specication refer to document SP04-2289 available on request

INSTALLATION INSTRUCTIONS FOR WALL MOUNTED LOOP POWERED AD-

DRESSABLE SOUNDERS, SOUNDER STROBES AND STROBE ONLY

NFX-WS-**

NFXI-WS-**

NFX-WSF-**

NFXI-WSF-**

NFX-WF-**

NFXI-WF-**

Signaling Line Supply Voltage (non isolation) 15 to 32VDC (24VDC typical)

Signaling Line Supply Voltage (isolation) 15 to 29VDC (24VDC typical)

Max current consumption (non isolation) (High Volume

Tone 8 @24V) 5.58mA 8.86mA N/A

Max current consumption (isolation) (High Volume Tone

8 @24V) 5.77mA 9.05mA N/A

Sound Output to EN54-3 (High Volume Tone 8 @24V) 95dB(A) ± 3dB N/A

Beacon ash rate N/A 1Hz 1Hz

Max current consumption (non isolation) NFX*-WF-** N/A N/A 3.28mA

Max current consumption (isolation) NFX*-WF-** N/A N/A 3.47mA

Quiescent Current 450uA

TERMINAL

CONNECTIONS

VOLUME SETTINGS

Volume setting is selected by SW6

and SW7 of the 8 way DIP switch. The

appropriate tone set is selected by SW1 to

SW5 of the 8 way DIP switch (see table 1).

The 2nd stage tone (related to the 1st stage

tone) is controlled by the re panel via the

protocol.

BASES/IP RATING

B501AP Base(IP 21C)

Deep Base(IP 44)

Waterproof Base(IP 65)

INSTALLATION

Afx B501AP base to a suitably at wall.

Terminate the cable to the appropriate

terminals. For surface mount wiring the cable

can enter the B501AP base via the break

outs provided. Select

the appropriate Tone and

Volume settings via the

DIP switch.

Locate the main

assembly on to the base

by rotating until it locks

into place.

CONTINUITY

SPRING

The B501AP base

incorporates a

continuity spring

between terminals

2 and 4. This allows the continuity of the eld

wiring to be checked without the need for the

device to be present. Inserting the device will

disengage the spring. Removing the device

will close the loop.

ANTI TAMPER LOCK

The B501AP base

also includes a tamper

resistant feature

that when activated

prevents removal of

the unit without the

use of a special tool.

This method is

consistent with the

anti tamper feature

across all devices

using this base. This

prevents the device

being turned to

enable its release.

SW6 SW7 Volume Setting

OFF OFF HIGH

OFF ON MEDIUM

ON OFF LOW

ON ON LOW

Breakout

If the waterproof option is required then the

wall gasket must be tted behind the deep

base, and the sealing o-ring tted after at-

taching the low prole base.

D1005 Issue 2

ADDRESS SETTING

To set one of the 159 available addresses for the device

use the two rotary switches located either side of the dip

switch unit. The ‘tens’ digits go from 0 to 15 and the ‘units’

from 0 to 9.

Sounder Output data, in accordance with EN54-3, is available on Document Ref: D 1022.

Note: For CPD Data on all relevant devices please request D974

We reserve the right to amend the content of this document without prior notice.

Table 1 - VERSION 8

KAC ALARM COMPANY LIMITED, KAC House, Thornhill Road, Redditch, Worcestershire, England. B98 9ND. www.kac.co.uk

DIMENSIONS

Strobe

Sounder/SounderStrobe

121mm

106mm

62mm

51mm

94mm

DIP setting Nominal 2nd Stage

O=Off/1=On No Pattern Frequency (WSO-WSS) (WSO-WSS) (WSO-WSS) Switching Frequency Description Market Standard Tone

SW 1,2,3,4,5 High Medium Low

0,0,0,0,0 1

Alternating 554/440 6.0/9.3 2.5/5.8 1.2/4.5 2Hz (100ms/400ms) French Fire Sound AFNOR France NFS 32-001 7

1,0,0,0,0 2

Alternating 800/970 5.4/8.7 2.9/6.2 1.4/4.7 1Hz UK BS5839 Pt1 8

0,1,0,0,0 3

Alternating 800/970 5.3/8.6 2.8/6.1 1.4/4.7 2Hz Alternating tone telecoms UK BS5839 Pt1, FP1063.1 8

1,1,0,0,0 4

Alternating 2400/2900 5.3/8.6 2.6/5.9 1.7/5.0 3Hz Alternating High Frequency 10

0,0,1,0,0 5

Alternating 2500/3100 6.7/10.0 2.6/5.9 1.8/5.1 2Hz Security Alarm 10

1,0,1,0,0 6

Alternating 988/645 5.9/9.2 2.5/5.8 1.4/4.7 2Hz 8

0,1,1,0,0 7

Continuous 660 5.0/8.3 2.5/5.8 1.2/4.7 All clear Sweden 1

1,1,1,0,0 8

Continuous 970 4.8/8.1 2.3/5.6 1.4/4.7 BS 5839 Pt 1 2

0,0,0,1,0 9

Continuous 1200 4.8/8.1 2.2/5.5 1.5/4.8 2

1,0,0,1,0 10

Continuous 2850 5.2/8.5 2.7/6.0 1.5/4.8 HF Continuous 4

0,1,0,1,0 11

Sweep 150-1000 5.5/8.8 2.5/5.8 1.4/4.7

Rising from 150Hz to 1000Hz in

10 seconds, then 40 seconds at

1000Hz, then falling from

1000Hz to 150Hz in 10

seconds, then 20 seconds at

150Hz, then repeating. Total

period 80 seconds.

“Gasalarm” Tone 22

1,1,0,1,0 12 Intermittent 420

6.2/9.5 2.6/5.9 1.1/4.4

0.625s on, 0.625 sec off AS2220 alert tone NZ, Aus AS2220

0,0,1,1,0 13 Sweep 500-1200

10.4/13.7 3.6/6.9 1.7/5.0

0.25 sec off, 3.75 sec on AS2220 evacuate tone NZ, Aus AS2220

1,0,1,1,0 14

Intermittent 660 5.0/8.3 2.4/5.7 1.2/4.5 3.33Hz 150ms on, 150ms off Swedish alarm tone Sweden 7

0,1,1,1,0 15

Intermittent 970 4.8/8.1 2.3/5.6 1.4/4.7 0.8Hz 0.25s on, 1s off Intermittent Tone UK BS 5839 Pt 1 8

1,1,1,1,0 16

Intermittent 970 4.8/8.1 2.3/5.6 1.4/4.7 0.5Hz 1s on, 1s off Back up alarm LF & BS5839

Pt 1 UK BS5839 Pt 1 8

0,0,0,0,1 17

Intermittent 2850 5.2/8.5 2.7/6.0 1.5/4.8 1Hz Back up alarm HF & BS5839

Pt 1 2nd tone UK BS5839 Pt 1 10

1,0,0,0,1 18

Intermittent 970 4.8/8.1 2.3/5.6 1.4/4.7 1Hz 500ms on, 500ms off LF BS5839 Pt 1 UK BS5839 Pt 1 8

0,1,0,0,1 19

Intermittent 950 4.3/7.6 2.1/5.4 1.3/4.6 0.22Hz (0.5s on, 0.5s off) rptx3,

1.5s off Australia ISO8201 12

1,1,0,0,1 20

Continuous 800 5.2/8.5 2.9/6.2 1.3/4.6 BS 5839 Pt 1 22

0,0,1,0,1 21

Sweep 400-1200 11.1/14.4 3.1/6.4 1.6/4.9 (0.5s on, 0.5s off)*3, 1.5s off Temporal 3 Evacuation tone Australia ISO8201 Temporal 3 12

1,0,1,0,1 22

Sweep 1200 - 500 10.3/13.6 3.3/6.6 1.7/5.0 0.99Hz 1s on, 0.01s off Evacuate, DIN tone & PFEER Germany DIN, PFEER 20

0,1,1,0,1 23

Sweep 2400 - 2850 5.0/8.3 2.6/5.9 1.9/5.2 7Hz Fast sweep VdS Germany VdS 10

1,1,1,0,1 24

Sweep 500 - 1200 10.3/13.6 3.5/6.8 1.7/5.0 (0.5s off, 3.5s on) Slow whoop evacuate

Netherlands Netherlands NEN 2575 8

0,0,0,1,1 25

Sweep 800 - 970 4.0/7.3 2.3/5.6 1.3/4.6 50Hz LF Buzz BS5839 Pt 1 UK BS5839 Pt 1 8

1,0,0,1,1 26

Sweep 800 - 970 4.5/7.8 2.5/5.8 1.4/4.7 7Hz Fast sweep LF BS5839 Pt 1 UK BS5839 Pt 1 8

0,1,0,1,1 27

Sweep 800 - 970 5.1/8.4 2.8/6.1 1.4/4.7 1Hz Medium sweep LF, BS5839 Pt

1, VdS UK, Germany BS5839 Pt 1 VdS 8

1,1,0,1,1 28

Sweep 2400 – 2850 4.9/8.2 2.6/5.9 1.8/5.1 50Hz High frequency buzz 10

0,0,1,1,1 29

Sweep 500 – 1000 5.4/8.7 2.5/5.8 1.3/4.6 7Hz Fast whoop 8

1,0,1,1,1 30

Sweep 500 – 1200 –

500 10.1/13.4 3.4/6.7 1.7/5.0 0.166Hz rise 1s, stable 4s, fall

1s Siren style tone 8

0,1,1,1,1 31

Sweep 800 – 1000 5.3/8.6 2.7/6.0 1.4/4.7 2Hz 8

1,1,1,1,1 32

Sweep 2400 - 2850 5.2/8.5 2.6/5.9 1.9/5.2 1Hz 10

Typical current consumption (mA)

Example B (Address setting 108)

Non-Isolated

Isolated

Note:- For Isolated variants add 0.19mA to high,

medium, low values above.

Isolated

Non-Isolated

Example A (Address setting 98)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Notifier Schiffsausrüstung Handbücher

Notifier

Notifier FS-BSO Bedienungsanleitung

Beliebte Schiffsausrüstung Handbücher anderer Marken

Clarion

Clarion CMS2 Reparaturanleitung

EBS

EBS M7000 Bedienungsanleitung

Kongsberg

Kongsberg M3 Bathy Bedienungsanleitung

NPK

NPK SCS-1002 Bedienungsanleitung

Furuno

Furuno FE-800 Bedienungsanleitung

Harken

Harken 1561 Bedienungsanleitung

Simrad

Simrad DD15 Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

E2S

E2S E2XS112UL Bedienungsanleitung

R2Sonic

R2Sonic 2026 Bedienungsanleitung

COBHAM

COBHAM SAILOR 6000 Bedienungsanleitung

Raymarine

Raymarine Maxiview ST80 Benutzerhandbuch

GUIDANCE MARINE

GUIDANCE MARINE 20- Series Montageanleitung

Raymarine

Raymarine ST60 Tridata Benutzerhandbuch

Sonic

Sonic 2024 Bedienungsanleitung

Quicksilver

Quicksilver 88688A25 Handbuch

Furuno

Furuno Navtex NX-700-A Bedienungsanleitung

olympia electronics

olympia electronics ΒS-532/WP Bedienungsanleitung