Novus 5000 Series Bedienungsanleitung
NHDC-5VE-5102
NHDC-5H-5102
User’s manual
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
2
DIRECTIVES AND PRELIMINARY INFORMATION
THE PRODUCT MEETS THE REQUIREMENTS CONTAINED IN THE FOLLOWING DIRECTIVES:
Information
The device, as an element of a professional CCTV system used for supervision and control, is not
intended for self-installation in households by people without specialist knowledge.
Obligation to consult the Manufacturer before performing an activity not provided for in the
operating manual or other documents:
Before performing an action that is not provided for in the User’s manual, other documents attached to
the Product or does not result from the normal purpose of the Product, please contact the Manufacturer
under the pain of excluding the Producer's liability for the consequences of such an action.
Pictures in this publication showing camera views can be simulations. Actual camera
images may vary depending on the type, model, settings, observation area, or
environmental conditions.
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member States
relating to electromagnetic compatibility (OJ L 96, 29.3.2014, p. 79–106, with changes).
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 4 July 2012 on waste electrical and electronic equipment WEEE)
(OJ L 197, 24.7.2012, p. 38–71,with changes).
DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment (OJ L 174, 1.7.2011, p. 88–110, with changes).
COMMISION DELEGATED DIRECTIVE (EU) 2015/863 of 31 March 2015 amending
Annex II to Directive 2011/65/EU of the European Parliament and of the Council as regards
the list of restricted substances.
DIRECTIVE (EU) 2017/2102 OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 15 November 2017 amending Directive 2011/65/EU on the restriction of the
use of certain hazardous substances in electrical and electronic equipment.
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
3
IMPORTANT SAFEGUARDS AND WARNINGS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A PROPER
DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE YOURSELF WITH
THE MANUAL PRIOR TO INSTALLATION AND FURTHER DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-
SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY
QUALIFIED SERVICE PERSONNEL AND SHOULD CONFORM TO ALL LOCAL
REGULATIONS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a direct
influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer is
forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers etc.)
is not recommended since it may lead to heat build-up and damaging the device itself as a
consequence;
8. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.
9. Device should be supplied only from a power sources whose parameters are in accordance with
those specified by the producer in the camera technical datasheet. Therefore, it is forbidden to
supply the camera from a power sources with unknown parameters, unstable or not meeting
producer’s requirements;
Due to the product being constantly enhanced and optimized, certain parameters and functions
described in the manual in question may change without further notice.
We strongly suggest visiting the www.novuscctv.com/en website in order to access the newest manual
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
4
GENERAL INFORMATION
1. Technical specification
IMAGE
Image Sensor CMOS sensor 1/2.9” GalaxyCore
Operang mode AHD 1080p, TVI 1080p, CVI 1080p, analog 960H, AHD 4MPX,
AHD 5MPX, TVI 4MPX, TVI 5MPX, CVI 4MPX
Min. Illuminaon 0 lx (IR on) - B/W mode
S/N Rao > 52 dB (AGC o)
Electronic Shuer auto: 1/50 s ~ 1/100000 s
Wide Dynamic Range (WDR) yes
Digital Noise Reducon (DNR) 2D
LENS
Lens Type varifocal, f=2.7 ~ 13.5 mm/F1.8
DAY/NIGHT
Switching Type mechanical IR cut lter
Switching Mode auto, manual
Visible Light Sensor yes
OTHER FUNCTIONS
OSD languages: English, others
Image Processing Defecve Pixel Correcon (DPC), sharpening
Remote control Yes (COAX protocol)
IR LED
LED Number 24
Range 20m
Smart IR yes (soware support)
INTERFACES
Video Output BNC, 1.0 Vp-p, 75 Ohm
INSTALLATION PARAMETERS
Degree of Protecon IP 66 (details in the user’s manual on page 7)
Power Supply 12 VDC
Power Consumpon 2.5 W, 6.5 W (IR on)
Operang Temperature -30°C ~ 40°C
Humidity max. 90%, relave (non-condensing)
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
5
GENERAL INFORMATION
2. Camera dimensions
NHDC-5H-5102: aluminium, white, fully cable managed wall mount bracket in-set included. Weight:
0.6 kg.
NHDC-5VE-5102: aluminium, white. Weight: 0.6 kg
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
6
3. Contents of the package
After opening, make sure that the package contains the following items:
• Camera
• Bag with mounting accessories
• User manual
If any of the items has been damaged in transit or is missing, pack the contents back into the original
packaging and contact the supplier.
Before starting the device, you should familiarize yourself with the description and role of individual
inputs, outputs and control elements that are equipped with cameras.
Caution:
If the device was brought from a room with a lower temperature, wait until it reaches the
temperature of the room in which it is to work. Do not switch the device on immediately after
bringing to a cooler place. The condensation of water vapor in the air can cause short circuits and
consequently damage the device.
4. Mounting
4.1. Bullet cameras - NHDC-5H-5102
• Referring to the location of the holes in the foot of the camera or using the mounting template,
mark the points for future mounting holes and the signal cable
• Drill mounting holes and a hole for the signal cable.
• Fix the camera foot using the enclosed pegs and screws, and connect the wires.
• Loosen the locking screw and adjust the position of the camera.
• After completing the adjustment, screw and tighten the lock screw.
• Adjust zoom and focus if needed using adjustment screws. It is recommended to check focus
settings in infrared illumination and make correction in color mode to have proper focus in both
modes.
GENERAL INFORMATION
Lens zoom
knob
Locking
screw
Vertical
adjustment
Horizontal
adjustment
Rotation adjustment
Lens focus
knob
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
7
4.2. Vandal proof cameras - NHDC-5VE-5102
• Loosen the Allen screw locking the base.
• Remove the stop ring, take the camera out of the base.
• Referring to the location of the holes in the base of the camera or using the mounting template,
mark the points for future mounting holes and the cable gland.
• Drill mounting holes and a hole for the signal cable.
• Mount the base with the included dowels and screws, and connect the wires.
• Place the camera on the base, put on the stop ring and pre-tighten the base locking screw.
• Adjust the position of the camera, and then tighten the base locking screw until it stops.
• Adjust zoom and focus if needed using adjustment screws. It is recommended to check focus
settings in infrared illumination and make correction in color mode to have proper focus in both
modes.
The declared degree of protection applies to camera housing, and does not take into account the
possibility of moisture penetrating through the connectors and connecting cables. Protecting the
connectors and cables against moisture is the responsibility of the installer. The manufacturer is
not liable for damages resulting from failure to fulfill the above-mentioned obligation.
5. Electrical connections
The camera should be powered by a stabilized power supply with parameters compatible with the
camera power supply. For the output of the video signal, use a coaxial cable with an impedance of 75Ω,
terminated with a BNC plug.
INSTALLATION AND ELECTRICAL CONNECTIONS
- BNC socket, video signal output
- 12VDC power socket
Stop ring
Zoom adjustment
Focus adjustment Illumination sensor
IR LEDs
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
8
6. Settings - camera’s menu
6.1. Access to the menu
Access to the camera menu is possible from the recorder menu:
• with the use of the PTZ menu: then entering the menu and confirming changes is done by
pressing the "Iris +" button and navigating the menu is possible using the directional buttons, or
• using the UTC remote control menu
6.2. Camera’s menu
The menu is divided into several sections where user can configure various options.
AE - exposure settings menu. You can set the image brightness, exposure type, and enable BLC (Back
Light Compensation).
AWB - white balance settings menu. The possible settings are ATW (automatic white balance) and
MWB (manual color level adjustment).
DAY/NIGHT - camera mode settings menu. Possible settings are AUTO (automatic day/night
switching), COLOR (color operation), B/W (black and white operation with IR illuminator on).
IMAGE ENHANCE - image settings menu. You can set the contrast, sharpness, color saturation and
enable 2D noise reduction mechanisms with wide dynamic range function DWDR. MIRROR opction
allow to use different mirroring function.
VIDEO OUTPUT - menu for selecting the camera work standard (AHD, TVI, CVI and CVBS) and
resolutions (5MP, 4MP, 1080P).
LANGUAGE - menu language change menu. The default language is English.
RESET - option to restore factory settings.
SETTINGS
After restoring the factory settings, save the changes using the SAVE&EXIT option
NHDC-5VE-5102, NHDC-5H-5102 User's manual version 1.1
All rights reserved © AAT SYSTEMY BEZPIECZEŃSTWA sp. z o.o.
9
SAVE&EXIT - saves the changes and exits the menu.
EXIT - closes the menu without saving changes.
SETTINGS
Closing the menu with the EXIT option does not cancel the previously introduced changes.
These changes remain in effect until a reset is performed or the camera is powered off and on.
27.10.2022 PF, MK v1.1
AAT SYSTEMY BEZPIECZEŃSTWA Sp. z o.o.
431 Pulawska St., 02-801 Warsaw, Poland
tel.: +4822 546 0 546, [email protected]
www.novuscctv.com
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Sprachen:
Andere Novus Digitalkamera Handbücher
Novus
Novus NVC-125B Bedienungsanleitung
Novus
Novus NVIP-2SD-6540/15 Bedienungsanleitung
Novus
Novus NVAHD-4DN3202V/IR-1-II Bedienungsanleitung
Novus
Novus NVAHD-1DN5301V-1 Bedienungsanleitung
Novus
Novus NVAHD-2DN5102H/IR-1 Bedienungsanleitung
Novus
Novus NVB-4010VB Bedienungsanleitung
Novus
Novus NVDN-601D/IR-white Bedienungsanleitung
Novus
Novus NVC-621D-white Bedienungsanleitung
Novus
Novus NVAHD-1DN5104H/IRH-2 Bedienungsanleitung
Novus
Novus 400 Series Bedienungsanleitung
Novus
Novus NVIP-5DN3512H/IR-1P Bedienungsanleitung
Novus
Novus NVAHD-1DN5106H/IR-1 Bedienungsanleitung
Novus
Novus NVC-BC2403D-II Bedienungsanleitung
Novus
Novus NVAHD-2DN3201MV/IR-1-PIR Bedienungsanleitung
Novus
Novus NVAHD-2DN5504MH/IR-1-II Bedienungsanleitung
Novus
Novus NVIP-4DN3500C-2P Bedienungsanleitung
Novus
Novus NVIP-4DN3514V/IR-1P Bedienungsanleitung
Novus
Novus NVAHD-2DN5504MD/IR-1 Bedienungsanleitung
