NTI ENVIROMUX Series Bedienungsanleitung

ENVIROMUX-DI16DO(R)16

Digital Input/Output Expander

Installation Manual

The ENVIROMUX-DI16DO(R)16 Digital Input/Output Expander enables the connection of up to 16 additional digital sensors and

output devices using just one RJ45 Sensor port on an ENVIROMUX-2D, ENVIROMUX-5D, or ENVIROMUX-16D Server

Environment Monitoring System (SYSTEM).

The ENVIROMUX-DI16DO16 includes digital outputs with an open-collector design for the control of up to 16 relays, solenoids,

LEDs, and other devices that operate at voltages between 0-24VDC (maximum 500mA).

The ENVIROMUX-DI16DOR16 includes digital outputs with a normally-open SPST relay design for the control of up to 16 different

devices that operate at a maximum125VAC (0.5A maximum) or maximum 30VDC (1.0A maximum).

Features

The ENVIROMUX-DI16DO16 and ENVIROMUX-DI16DOR16 have many features in common, and several differences, detailed

below:

Features in common:

•Interfaces with the SYSTEM via the RJ45 Sensor Port

•Digital inputs:

o16 screw terminal pairs for connecting dry contact devices

One screw terminal pair for tachometer; 0 to 255 Hz

oAccepts 26 to 16AWG wire

oPotential free

oVoltage range: 0 to +36VDC

oOver-voltage surge protected

•Supports 18-24AWG CAT5/5e/6 cable up to 500 ft. (152.4 m)

Feature differences:

Feature ENVIROMUX-DI16DO16 ENVIROMUX-DI16DOR16

Digital outputs

•16 screw terminal pairs for open-

collector outputs

•Accepts 26 to 16AWG wire

•Rated sink current: 500mA per output

•+5VDC, 22kΩpull-ups

•Voltage range: 0 to +24VDC

•Over-voltage surge protected

•16 screw terminal pairs for normally-open relay

contact outputs

•Accepts 26 to 16AWG wire

•Potential free

•Rated switching load: 0.5A @ 125 VAC, 1.0A @

±30VDC

•Fused

Power supply Requires 75mA at 5VDC (Powered by

SYSTEM) Includes 120VAC or 240VAC at 50 or 60Hz-5VDC/3.0A

AC Adapter

Dimensions (WxDxH) 6.49x3.10x1.08 in (165x79x27 mm) 6.49x3.10x1.78 in (165x79x45 mm)

ENVIROMUX®Series ENVIROMUX-DI16DO16 (Front and Rear View)

ENVIROMUX-DI16DOR16 (Rear View)

Installation

1. Connect the Expander to the SYSTEM using up to 500 feet (152.4 m) of 18-24AWG CAT5, 5e, or 6 cable.

2. Dry contact sensors can then be connected to the

Expander using 26-16AWG wire. Up to 16 sensors

can be connected.

Two-wire switch-only type sensors can be connected to

the plus (+) and ground ( ) terminals of each of 16 sets

of terminals.

Terminal pair 1 is specially designed for connection of

a tachometer/anemometer with a range of 0-255Hz (like

the ENVIROMUX-WSS Wind Speed Sensor).

3a. Digital Outputs on the ENVIROMUX-DI16DO16 have an open-collector design for the control of up to 16 relays, solenoids,

LEDs, and other devices that operate at voltages between 0-24VDC (maximum 500mA). Devices connected to Digital Outputs

will display in the “Remote Output Relay” list in the SYSTEM web interface for assignment to sensor alert responses.

3b. Output Relays on the ENVIROMUX-DI16DOR16 have a normally-open SPST relay design for the control of up to 16 different

devices that operate at maximum 125VAC (0.5A maximum) or maximum 30VDC (1.0A maximum). Devices connected to

Output Relays will display in the “Remote Output Relay” list in the SYSTEM web interface for assignment to sensor alert

responses.

View of “Remote Output Relay” list on

the web interface Summary Page

(Output Relays from two ENVIROMUX-

DI16DO16 are shown)

Web Interface- Summary Page

The Summary Page of the SYSTEM will display sensors connected to the ENVIROMUX-DI16DO(R)16 in a separate list labeled

“Remote Digital Inputs”. (The image below demonstrates the summary page with two ENVIROMUX-DI16DO16 Digital

Expanders connected.)

The SYSTEM will also recognize the number 1 connector set on the ENVIROMUX-DI16DO(R)16 as a possible tachometer

connector, displaying its status under “Sensors”. If a tachometer is being connected, configure the sensor as such. If a water

sensor or dry-contact sensor is going to be connected to connection 1 (Connection “1.1” or “2.1” below), ignore the listing under

“Sensors” and configure the listing under “Remote Digital Inputs”. Do not configure both.

Remote

Connections

To configure

Input #1 for

connection

to tachometer

First

ander

Second

Expander

When configuring the Remote Digital Inputs for connection to a water sensors or dry-contact sensors, configure them just as you

would any other Digital Input as described in the manual for the SYSTEM.

When configuring the use of Remote Output Relays, configure them also as described for Output Relays in the manual for the

SYSTEM.

To view the status of a tachometer connected to Digital In #1, Click on the Sensor description or click on “View”

The status page for the sensor will open, displaying the default value of the sensor with a 0-255Hz range of sensing operation.

To configure the sensor for specific use, click on “Configure” to open a page with variable values (see image on next page).

Most of the sensor settings are the same as any other sensor configuration (detailed in the SYSTEM manual) but there are some

differences:

Sensor Settings Description

Associate Sensor Select if the Type “DIO” should be replaced by the sensor type to be entered in the next box.

Associated Sensor Type Enter the “Type” of sensor that should be displayed on the summary page and in all alert

communications received regarding this sensor

Associated Sensor Unit Enter between 1 and 3 alphabetical characters. (Ex. MPH for Miles Per Hour) These

characters will be used by the ENVIROMUX to represent the unit of measure reported by the

attached sensor. Leaving it empty will result in an empty string in the reported data. For

example, a value will be reported on the status page, but no unit of measure will be displayed.

SNMP Associated Type ID Enter ID value from MIB file if SNMP traps will be used for alert notifications for this sensor (for

more on this, see “SNMP Custom Type ID” on next page)

Min. Associated Level The minimum range of the units to be associated with the cycle count measured from the

attached sensor.

(Ex. the ENVIROMUX-WSS associates one rotation within 1 second to be a wind speed of

2.5MPH. With an maximum operating range of 255Hz (or cycles), the maximum wind speed

measurement will be 637.5MPH (255Hz X 2.5MPH).)

Max. Associated Level The maximum range of the units to be associated with the current reading measured from the

attached sensor.

Click here to open

confi

uration

o view status,

click either link

SNMP Custom Type ID: Use this field if SNMP traps will be used for alert notifications. The Type ID corresponds with a value

defined in the MIB file under “extSensorType” (default value is 32567 for type “Custom”). Place the desired number in this box

that represents the type of sensor to be reported in the MIB browser or SNMP trap.

To define a new type of sensor;

1. open the MIB file,

2. locate the section titled “extSensorType”,

3. assign a description and a number not already in use (in the “SYNTAX” field) to associate with it ,

4. enter the number for the newly defined extSensorType in the SNMP Custom Type ID box.

If the Type ID is left blank, the value “0” will be assigned, which will be reported in the browser and SNMP trap as type

“undefined”.

Default configuration page for tachometer

Configuration of tachometer as a wind speed sensor (ENVIROMUX-WSS)

255Hz (cycles) x 2.5MPH per rotation

in 1 second (cycle)

Check this box if you enter data in the

next 5 boxes

CAT5 Cable

The CAT5 connection cable between the SYSTEM and the ENVIROMUX-DI16DO(R)16 is terminated with RJ45 connectors and

must be wired according to the EIA/TIA 568 B industry standard. Wiring is as per the table and drawing below.

Pin Wire Color Pair

1 White/Orange 2

2 Orange 2

3 White/Green 3

4 Blue 1

5 White/Blue 1

6 Green 3

7 White/Brown 4

8 Brown 4

TRADEMARK

ENVIROMUX is a registered trademark of Network Technologies Inc in the U.S. and other countries.

in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,

without the prior written consent of Network Technologies Inc, 1275 Danner Drive, Aurora, Ohio 44202.

CHANGES

The material in this guide is for information only and is subject to change without notice. Network Technologies Inc reserves the

right to make changes in the product design without reservation and without notification to its users.

MAN168 REV 4/20/2016

Pair 2 Pair 1 Pair 4

Pair 3

(View Looking into RJ45 Socket)

Andere Handbücher für ENVIROMUX Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NTI Extender Handbücher

NTI

NTI ST-IPHD-L-2GOPOE Bedienungsanleitung

NTI

NTI ST-IPHD-IR-LC Bedienungsanleitung

NTI

NTI XTENDEX Series Bedienungsanleitung

NTI

NTI XTENDEX Series Bedienungsanleitung

NTI

NTI ST-C5HDA-600 Bedienungsanleitung

NTI

NTI ST-C5KVM-600 Bedienungsanleitung

NTI

NTI USB2-C5-4LC-328 Bedienungsanleitung

NTI

NTI XTENDEX ST-C6FOUSBDP4K- LC Bedienungsanleitung

NTI

NTI XTENDEX Series ST-C5RS-LCRS232 Bedienungsanleitung

NTI

NTI XTENDEX ST-C6DVI-300 Bedienungsanleitung

NTI

NTI XTENDEX ST-FO4K18GB-RSLA-LCV2 Bedienungsanleitung

NTI

NTI XTENDEX ST-IPFOUSB4K-L-LCVW Bedienungsanleitung

NTI

NTI XTENDEX Series Bedienungsanleitung

NTI

NTI XTENDEX ST-C6HD-HDBT-LC Bedienungsanleitung

NTI

NTI USB-C5-200 Bedienungsanleitung

NTI

NTI XTENDEX ST-C6DVIA-IR-R-300 Bedienungsanleitung

NTI

NTI ST-WL4K-98 Bedienungsanleitung

NTI

NTI USB2-C5-4LC Bedienungsanleitung

NTI

NTI ST-FO4K10GB-LC Bedienungsanleitung

NTI

NTI XTENDEX Series Bedienungsanleitung

NTI

NTI XTENDEX ST-C6USBH-HDBT Bedienungsanleitung

NTI

NTI ST-UP4K18GB-L-RS Bedienungsanleitung

NTI

NTI XTENDEX ST-C5KVMA-600 Bedienungsanleitung

NTI

NTI XTENDEX USB-C5 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung