Numark 4TRAK Bedienungsanleitung

SPECIFICATION

FUNCTION

1. POWER SWITCH – Turns 4TRAK on and off. Turn on 4TRAK after all input devices have been connected and

before you turn on amplifiers. Turn off amplifiers before you turn off 4TRAK.

2. POWER INPUT – Use the included power adapter to connect the 4TRAK to a power outlet. While the power is

switched off, plug the power supply into the 4TRAK first, then plug the power supply into a power outlet.

3. USB PORT – Connect the 4TRAK to the included 4TRAK FX KOMMAND CONSOLE and your 4TRAK can be

used as a software controller device using USB MIDI protocol or as a pass-through audio interface.

4. MASTER OUTPUT (XLR) – Connect this XLR output to a PA system or powered monitors.

5. MASTER OUTPUT (RCA) – Use standard RCA cables (not included) to connect this output to a speaker or

amplifier system.

6. BOOTH/ZONE – Use standard RCA cables (not included) to connect this output to a monitoring system.

7. RCA INPUT – Connect audio sources to these inputs.

8. LINE/MIC SWITCH – Flip this switch to the appropriate position, depending on the device connected to the

RCA inputs. If using a line-level device, such as a CD player or sampler, set this switch to "LINE." If using a

microphone, set this switch to “MIC”.

9. MIC INPUT – Connect a 1/4" mic to this input.

10. LINE/PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the

RCA inputs. If you are using phono-level turntables, set this switch to "PHONO" to provide the additional

amplification needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set

this switch to "LINE."

11. GROUND – If using phono-level turntables with a grounding wire, connect the grounding wire to these

terminals. If you experience a low "hum" or "buzz", this could mean that your turntables are not grounded.

12TAP – Pressing this button in time with the beat will help determine the BPM of the track.

13. LOOP LENGTH – Halves or doubles the length of your Auto Loops or currently selected loop.

14. BEATJUMP – Changes the function of the Loop Shift buttons to Beatjump.

SERVICE MANUAL

MODEL:4TRAK

15. LOOP SHIFT – Adjusts the Loop Out point (when not in Beatjump Mode). When in Beatjump Mode,

1pressing a Loop Shift button will cause the track to jump ahead or back by a beat.

16. IN – This button sets the beginning point of a loop.

17. OUT – This button sets the ending point of a loop. When outside of a loop, press this button to jump

back to your last selected loop. Press Shift + Out to set a 2-beat Auto Loop.

18.PITCH SLIDER – This controls the speed of the music. Moving towards the "+" will speed the music up,

while moving towards the "–" will slow it down.

19. PITCH BEND – Allows you to briefly adjust the speed of the music faster or slower for as long as the

button is held. Useful for beat-matching two songs that might be at the same tempo but whose beats

are not quite aligned.

20.CUE – Returns and pauses the music at the last set cue point. The default cue point is at the beginning of the

track, but you can set a different cue point by pressing this button at a different point in the track when it is

paused

STANDARD

1.MaxMSP test program for production Line

2. AP test specification

RCABalanceOutput

Voltage AC100V~240V50~60Hz

MASTER:2 ±0.5V

Volume BOOTH:2 ±0.5V

BALANCED:12 ±2V

Distortion defection 0.03% below

S/N 70dBrupward

Separation 70dBrupward

F/R 20~20KHz ±0.5dB

DISASSEMBLY PROCEDURES

1. REMOVAL OF BOTTOM CHASSIS. (Fig1)

(A) TAKE OUT THE 4 PCS SCREWS FROM THE BACK HOLDER..

Fig.1

2. REMOVAL OF BOTTOM CHASSIS. (Fig2)

(A) TAKE OUT THE 21 PCS SCREWS FROM THE BOTTOM CHASSIS.

Fig.2

DISASSEMBLY PROCEDURES

3.REMOVAL HEADPHONE PCB AND DOUSER ASSEMBLY AND XLR JACK ASSEMBLY. (Fig3)

(A) TAKE OUT THE 3 PCS KNOB.

(B) TAKE OUT THE 9 PCS SCREWS，TAKE OUT THE 1 PC NUT HOLDER AND TAKE OUT THE 2 PCS

CONNECTORS.

(D) TAKE OUT THE 6 PCS SCREWS，TAKE OUT THE 2 PCS CONNECTORS AND TAKE OUT THE 2 PCS

DOUSER ASSEMBLY.

(E) TAKE OUT THE 4 PCS SCREWS FROM THE XLR JACK ASSEMBLY.

(F) TAKE OUT THE 5 PCS SCREWS，TAKE OUT THE 2 PCS NUT HOLDER AND TAKE OUT THE 5 PCS

CONNECTORS.FROM THE AN PCB.

Fig.3

DISASSEMBLY PROCEDURES

4. REMOVAL OF CROSS FADER ASSEMBLY AND KNOB. (Fig4)

(A) TAKE OUT THE 1 PC KNOB FROM THE PANEL.

(B) TAKE OUT THE 2 PCS SCREWS AND 1 PC CONNECTORS FROM THE PANEL.

Fig.4

5. REMOVAL OF MIXER PCB AND LEFT PCB.(Fig5)

(A) TAKE OUT THE 23 PCS SCREWS AND 6 PCS CONNECTORS FROM THE MIXER PCB.

(B) TAKE OUT THE 16 PCS SCREWS AND 3 PCS CONNECTORS FROM THE LEFT PCB

Fig.5

DISASSEMBLY PROCEDURES

1. REMOVAL OF BOTTOM CHASSIS. (Fig1)

(A) TAKE OUT THE 12 PCS KNOB

(B).TAKE OUT THE 8 PCS SCREW FROM THE PANEL

Fig.6

Andere Handbücher für 4TRAK

Inhaltsverzeichnis

Andere Numark DJ-Equipment Handbücher

Numark

Numark Party Mix Pro Bedienungsanleitung

Numark

Numark OMNI CONTROL Gebrauchsanweisung

Numark

Numark NS6 Bedienungsanleitung

Numark

Numark CDN450 Bedienungsanleitung

Numark

Numark DJ Equipment Gebrauchsanweisung

Numark

Numark MIXDECK Installationsanleitung

Numark

Numark NDX500 Bedienungsanleitung

Numark

Numark 4TRAK Bedienungsanleitung

Numark

Numark DJio Bedienungsanleitung

Numark

Numark MIXDECK EXPRESS Bedienungsanleitung

Numark

Numark iM1 Bedienungsanleitung

Numark

Numark DJ2GO Bedienungsanleitung

Numark

Numark MIXDECX QUARD Bedienungsanleitung

Numark

Numark Mixtrack Bedienungsanleitung

Numark

Numark NS6 Gebrauchs- und Wartungshandbuch

Numark

Numark NPM5 Bedienungsanleitung

Numark

Numark MIXTRACK PLATINUM Bedienungsanleitung

Numark

Numark IDJ PRO Bedienungsanleitung

Numark

Numark D2 Director Bedienungsanleitung

Numark

Numark MixTrack Pro FX Bedienungsanleitung

Numark

Numark iDJ Technisches Dokument

Numark

Numark DIGITAL DIAMOND THED2 Bedienungsanleitung

Numark

Numark DDS80 Bedienungsanleitung

Numark

Numark C3 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung