Nvent RAYCHEM RayClic-E Bedienungsanleitung

DESCRIPTION

This end seal is for use with nVent RAYCHEM IceStop, XL-Trace,

HWAT and RaySol heating cables. Materials for one end seal

termination are included in this kit. The appropriate nVent

RAYCHEM power connection kit must also be used. These

installation instructions should be used in conjunction with the

IceStop, XL-Trace, HWAT and RaySol System Installation and

Operation Manuals. For technical support contact your nVent

representative or call nVent (800)545-6258.

Note: The nVent RAYCHEM RayClic-E end seal can be installed

only once; it cannot be removed from the heating cable. Do not

use until ready for final installation.

TOOLS REQUIRED

• Utility knife

• Diagonal cutters

KIT CONTENTS

Qty Description

1 Gel-filled end seal

APPROVALS

With HWAT, IceStop, and

XL-Trace heating cables

Class I, Div. 2, Groups A, B, C, D

hazardous locations with GM-XT only

718K Pipe Heating Cable

877Z De-Icing and Snow Melting

Not UL Listed with XL-Trace

heating cable for buried piping

APPROVED

-w

RayClic-E

RayClic End Seal Kit Installation Instructions

This component is an electrical device that

must be installed correctly to ensure proper

operation and to prevent shock or fire. Read

these important warnings and carefully follow

all the installation instructions.

• To minimize the danger of fire from

sustained electrical arcing if the heating

cable is damaged or improperly installed,

and to comply with the requirements of

nVent, agency certifications, and national

electrical codes, ground-fault equipment

protection must be used. Arcing may not be

stopped by conventional circuit breakers.

• Bus wires will short if they contact each

other. Keep bus wires separated.

• The black heating cable core is conductive

and can short. It must be properly insulated

and kept dry.

• Component approvals and performance are

based on the use of nVent-specified parts

only. Do not use substitute parts or vinyl

electrical tape.

• Use only fire-resistant insulation materials

such as fiberglass wrap.

• Leave these instructions with end user for

reference and future use.

WARNING:

HWAT IceStop, XL-Trace, and RaySol

• Score down and around outer

jacket 1 inch from the end.

• Remove the outer jacket.

• Do not cut or damage inner jacket.

• Using wire cutters, cut away aluminum wrap close to

braid and outer jacket.

• Remove exposed braid.

• Push end seal completely onto heating cable.

Note: The end seal can be

installed only once; it cannot

be removed from the heating

cable. Do not use until ready

for final installation.

nVent reserves the right to change specications without notice.

Raychem-IM-H55428-RayClicE-EN-1805

nVent.com

North America

Tel +1.800.545.6258

Fax +1.800.527.5703

[email protected]

Europe, Middle East, Africa

Tel +32.16.213.511

Fax +32.16.213.604

[email protected]

Asia Pacific

Tel +86.21.2412.1688

Fax +86.21.5426.3167

[email protected]

Latin America

Tel +1.713.868.4800

Fax +1.713.868.2333

[email protected]

Andere nvent Kabel und Steckverbinder Handbücher

nvent

nvent RAYCHEM C25-100-METAL-FHP Bedienungsanleitung

nvent

nvent Raychem C20-01-F Bedienungsanleitung

nvent

nvent Raychem HAK-C-100 Bedienungsanleitung

nvent

nvent Erico Ericore Bedienungsanleitung

nvent

nvent RAYCHEM HWT-P Bedienungsanleitung

nvent

nvent Raychem C25-100-METAL Bedienungsanleitung

nvent

nvent RAYCHEM BTV Handbuch

nvent

nvent Raychem E-150-F Bedienungsanleitung

nvent

nvent Raychem E-50-F Bedienungsanleitung

nvent

nvent Raychem S-150 Bedienungsanleitung

nvent

nvent Raychem GM-2CW Bedienungsanleitung

nvent

nvent JBS-100-A Bedienungsanleitung

nvent

nvent Raychem C20-02-F Bedienungsanleitung

nvent

nvent Raychem JBM-100-EP Bedienungsanleitung

nvent

nvent Raychem TraceTek TT-7000-HUV-CK-MC-M Bedienungsanleitung

nvent

nvent LENTON Bedienungsanleitung

nvent

nvent JBS-PI-EP Bedienungsanleitung

nvent

nvent Raychem C25-100-FHP Bedienungsanleitung

nvent

nvent raychem ETL-GLAND-01 Bedienungsanleitung

nvent

nvent RAYCHEM Bedienungsanleitung

nvent

nvent JBS-100-STB Bedienungsanleitung

nvent

nvent Raychem E-100-E Bedienungsanleitung

nvent

nvent RAYCHEM H908 Bedienungsanleitung

nvent

nvent Raychem C25-100 Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken

Philips

Philips SWA6310 Bedienungsanleitung

StarTech.com

StarTech.com CRJ4550PK Bedienungsanleitung

Nohau

Nohau EMUL-IP2K-PC Bedienungsanleitung

Foxun

Foxun SX-SP144E-HD4K2K Bedienungsanleitung

Philips

Philips SWA3305W Bedienungsanleitung

opticis

opticis Stretch DVIM1-1P0x Bedienungsanleitung

Volkswagen

Volkswagen VAS 6558A Bedienungsanleitung

NEXIBO

NEXIBO N-13 Bedienungsanleitung

CYP

CYP PU-1H3HBTL Bedienungsanleitung

Allen-Bradley

Allen-Bradley 1784-u2dhp Bedienungsanleitung

Global Caché

Global Caché Flex Link Blaster Bedienungsanleitung

Hauppauge

Hauppauge USB-Live2 Bedienungsanleitung

Fenix

Fenix MPSV 15 Bedienungsanleitung

BEGA

BEGA 71 085 Bedienungsanleitung

Tesla

Tesla HPWC Bedienungsanleitung

GAMERON

GAMERON LUXURY TV CABLE Bedienungsanleitung

molex

molex Milli-Grid Dual row 87568 Series Bedienungsanleitung

Burndy

Burndy Continental Industries thermOweld CRE-7 Bedienungsanleitung

nvent RAYCHEM RayClic-E Bedienungsanleitung

Beliebte Kabel und Steckverbinder Handbücher anderer Marken