Nvidia Clara AGX Bedienungsanleitung

Clara AGX –Getting Started 
 NVIDIA Confidential 1 
 
Clara AGX Developer Kit User Guide 
 
Purpose: Provides the instructions to flash, setup, and start using a Clara AGX Developer Kit. 
 
Disclaimer: The Clara AGX Developer Kit is not an approved medical device and is not 
intended for clinical use. 
 
Version: 1.5 
 
Contents 
Checklist for Setting up the Developer Kit ............................................................. 2 
Hardware Setup............................................................................................. 2 
Requirements............................................................................................. 2 
Precautions ............................................................................................... 2 
System Overview ........................................................................................... 3 
Main Components ........................................................................................ 3 
Tech Specs................................................................................................ 3 
I/O and external interfaces ............................................................................ 4 
Powering up the System ................................................................................... 6 
Check Firmware Version and Manually Update if Needed ............................................ 7 
Flashing and Updating Clara AGX Developer Kit using SDK Manager ................................ 8 
Switching between iGPU and dGPU...................................................................... 8 
Setting up SSD Storage.................................................................................... 10 
Create Partition......................................................................................... 11 
Mount Partition ......................................................................................... 12 
Setting up Docker and Docker Storage on SSD ........................................................ 12 
Move Docker Storage to m2 Partition................................................................ 13 
Install the Clara Holoscan SDK........................................................................... 14 
Known Issues ............................................................................................... 14 
Additional Resources...................................................................................... 14 
Compliance Information.................................................................................. 15 
 
 

Clara AGX –Getting Started

NVIDIA Confidential 2

Checklist for Setting up the Developer Kit

After receiving the Clara AGX Developer Kit, ensure the following actions are taken before

developing on the kit. Each action is described in its corresponding section of this user guide.

•Read through the Hardware Setup requirements and precautions.

•Familiarize yourself with the System Overview: the main components and system I/O.

•Power up the system.

•If you had previously flashed the devkit, check firmware version and manually update if

needed. If this is your first time flashing, come back to the step at the end of the

checklist.

•Flash and update the Clara AGX Developer Kit with Jetpack using SDK Manager.

•Switch from iGPU to dGPU mode.

•Set up the 250GB SSD storage.

•Set up Docker and Docker storage.

•Install the Clara Holoscan SDK from Github.

Hardware Setup

Requirements

•A Clara AGX Developer Kit

•A compatible power cable

oYour NVIDIA Clara AGX Developer Kit may not include a power cable compatible

with your local electrical requirements.

oA compatible cable should meet the following requirements:

▪Provides a certified local 3-prong AC power plug

▪Provides a C13 connector

▪Supports ratings of 100-120VAC/6A, 200-240VAC/3A, or higher with a

minimum wire thickness of 18AWG and insulation rating of 300V or higher.

•An Ubuntu 18.04 / 20.04 host system (for use during flashing)

•A standard USB-A to USB-C or USB-C to USB-C cable with data enabled (for use during

flashing)

•Connection to the Internet for the host system before and during flashing, and for the

Clara AGX Developer Kit during flashing

•A keyboard, mouse, and monitor with HDMI for the Clara AGX Developer Kit

Precautions

•Only connect and disconnect a PCIe card (e.g. miniSAS or dGPU) when the system is

powered down.

•Apply extra care when plugging and removing PCIe cards to avoid stress on the PCIe

connectors (wearing, bending, breaking).

•The rightmost USB connector is USB 2.0 (even if the color is blue). The other two USB

connectors are USB 3.0.

Clara AGX –Getting Started

NVIDIA Confidential 3

System Overview

Main Components

The Clara AGX Developer Kit contains the following major components:

•AGX Xavier 32 GB Module

•RTX 6000 discrete GPU

•ConnectX-6 IC

•250GB Removeable SSD

Tech Specs

CPU

8-core Carmel ARM v8.2 64-bit CPU, 8MB L2 + 4MB L3

Memory

32GB 256-Bit LPDDR4x | 136.5GB/s

GPU

RTX6000 | 24 GB GDDR6 | 672 GB/s | 4,608 CUDA cores | 576 Tensor Cores

Storage

250GB SSD

I/O

Clara AGX –Getting Started

NVIDIA Confidential 4

Expansion

PCIe x8 (single slot width) to Xavier | PCIe x8 (single slot width) to RTX6000

Power Supply

750W | 100-240V

Dimensions

227mm W x 149mm H x 332mm L

I/O and external interfaces

1) Power cable connection

2) Power switch

3) PCIe slots for customer cards

4) dGPU outputs from RTX 6000, including four Display Ports and one mini HDMI port

a. Reference the GPU section below to determine which display output to use.

Clara AGX –Getting Started

NVIDIA Confidential 5

5) 100 GbE QSFP28 Ethernet connector to NVIDIA ConnectX-6

6) 10 GbE RJ45 Ethernet connector to NVIDIA ConnectX-6

a. The 10GbE connector only supports 10 GbE speeds.

7) 1 GbE RJ45 Ethernet connector to Xavier module

8) USB 3.0 ports (2x)

9) USB 2.0 port (1x)

10) HDMI out

a. Reference the GPU section below to determine which display output to use.

11) HDMI in: Connect to instruments that output HDMI to the platform.

12) Debug USB-C port: Connect to the Linux host system for flashing and serial port

connections.

13) x8 PCIe slot (x16 physical) for customer card, to Xavier Module

14) x8 PCIe slot (x16 physical) for customer card, to RTX6000

Clara AGX –Getting Started

NVIDIA Confidential 6

a. Used for cards supporting GPU Direct RDMA data transfer to RTX6000 GPU

15) SD card slot

16) Recovery button

17) Reset button

18) Main secondary compartment fan connector (there is an additional system fan inside the

chassis)

19) Auxiliary fan connector for card fans

20) Power button

To access ports 13-19, remove the left-hand side cover. The process is illustrated below.

Unscrew the two Phillips screws (21 and 22) that secure the cover at the back of the machine.

Next, push and slide the cover in the direction towards the back of the machine without lifting

(step 1). It should slide about 0.5 inch, or less than 1.5 cm. Finally, you should be able to lift

the cover off once it has more than one degree of freedom and can be easily lifted upwards

(step 2).

Powering up the System

1) Connect all peripherals to the system before powering up the system.

2) Connect the power cable to the system in the slot labeled (1) in the graphic above.

3) Once the power is connected, press the power button (20) for less than 1 second. It should

light up.

4) If you have a display connected, you might already see the system booting on it. During

flashing or re-flashing, use the HDMI output port (10) to connect to the display. Reference

the GPU section below to determine how to choose between display outputs in different

modes.

Clara AGX –Getting Started

NVIDIA Confidential 7

Note: The machine can be powered off by depressing the power button for approximately 10

seconds.

Check Firmware Version and Manually Update if Needed

If you are a current user of the Clara AGX Developer Kit and have flashed your devkit before,

check and if needed, update the firmware on the devkit before moving on to the next step of

flashing Jetpack 5.0 (compatible with Clara Holoscan SDK v0.2). Without the firmware update,

you might experience Known Issue #1 once Jetpack 5.0 is installed.

If you are a new user of the Clara AGX Developer Kit and have not flashed your devkit before,

follow the rest of this document to set up your devkit, then come back to this section to check

and update your firmware after switching to dGPU mode.

1. Install the tools for checking and updating firmware version

$ sudo apt install mstflint

2. Check for device address and look for the address for “Ethernet controller: Mellanox

Technologies MT28908 Family [ConnectX-6]”. The old firmware uses 0000:09:00.0 address, the

up-to-date firmware should use 0000:03:00.0.

$ lspci | grep Mellanox

3. Run the command with the device address obtained in step 2 to check for the firmware

version. If you see a version lower than 20.33.1048 then firmware update is needed. Otherwise,

there’s no need to update your firmware if the current version is 20.33.1048, you can skip the

rest of steps 4 - 7.

$ sudo mstflint -d 0000:09:00.0 q full

…

FW Version: 20.27.4006 <- Update is needed

…

$ sudo mstflint -d 0000:03:00.0 q full

…

FW Version: 20.33.1048 <- Firmware is already updated

…

4. Download the new firmware from here and unzip.

5. Install new firmware.

$ sudo mstflint -d 0000:09:00.0 -i fw-ConnectX6-rel-20_33_1048-

Nvidia_McCoy_LOM_PCIe_switch_Ax.bin burn

6. Reboot the devkit.

7. Check the newly installed firmware has correct version.

$ sudo mstflint -d 0000:03:00.0 q full

…

FW Version: 20.33.1048

…

Clara AGX –Getting Started

NVIDIA Confidential 8

Flashing and Updating Clara AGX Developer Kit using SDK Manager

1. Register and activate an NVIDIA Developer Account here to access the latest version of

Jetpack in SDK Manager.

2. If you are running a VPN on your host system, log off before flashing the Clara AGX Developer

Kit.

3. Using a VM as your host machine isn’t officially supported, but it is possible with certain

VMs such as VMWare Workstation 16 running Ubuntu 18.04. If using a VM, ensure the USB

port that connects to the USB-C port on the Clara AGX Developer Kit is always routed to the

VM.

4. From the host system, download and install the latest version of NVIDIA SDK Manager.

Instructions for downloading and setting up NVIDIA SDK Manager can be found here.

5. Connect the Clara AGX Developer Kit to the host system via USB-C (12).

6. From the NVIDIA SDK Manager, download and flash the Clara AGX Developer Kit. See the

step-by-step instructions for more details.

a. If you joined the Clara Holoscan SDK program after your initial SDK Manager login,

you will need to log out and log in again on SDK Manager for the permissions to take

effect.

b. NVIDIA recommends putting the unit to reset mode for the flashing process in Manual

Setup mode, as it has been observed that flashing can be stuck in Automatic Setup

mode.

c. Follow these steps to reset the Clara AGX Developer Kit:

i. Remove the left-hand side cover to expose ports 13-19

ii. While the unit is powered on, press the Recovery button (16) + Reset button

(17), then release both buttons.

d. If resetting the unit doesn’t work, try putting the unit into recovery mode:

i. Power off the unit.

ii. Remove the left-hand side cover to expose ports 13-19

iii. Hold down the Recovery button (16) while pressing the Power button (20) to

turn on the unit.

iv. Release the Power Button, then the Recovery button.

7. NVIDIA recommends putting the devkit into reset mode during flashing, but if for any reason

you need to know the default credentials when SDK Manager is preparing to flash the Clara

AGX Developer Kit, it is shown below

a. Username: ubuntu

b. Password: ubuntu

Switching between iGPU and dGPU

The Clara AGX Developer Kit can use either the Xavier AGX module GPU (iGPU, integrated GPU)

or the RTX6000 add-in card GPU (dGPU, discrete GPU). You can only use one type of GPU at a

time.

By default, the Clara AGX Developer Kit uses the iGPU. Switching between the iGPU and dGPU

is performed using the nvgpuswitch.py script, located at the /opt/nvidia/l4t-gputools/bin/

directory. To make the nvgpuswitch.py script accessible globally, copy it to a directory included

in $PATH if it hasn’t been already:

Clara AGX –Getting Started

NVIDIA Confidential 9

$ sudo cp /opt/nvidia/l4t-gputools/bin/nvgpuswitch.py /usr/local/bin/

To switch from the iGPU to the dGPU, follow these steps:

1. Connect the Clara AGX Developer Kit to the Internet using one of the following methods:

a. An Ethernet cable connected to a router or Wi-Fi extender

i. Use the 1GbE connector to the Xavier module at port 7

b. A USB Wi-Fi receiver

i. Not all USB Wi-Fi receivers will work out of the box on the Clara AGX

Developer Kit.

ii. The USB Wi-Fi receiver should have support for Ubuntu 20.04

iii. The TP-Link Archer T2U Nano USB Wi-Fi Adapter which has previously

been working with the Ubuntu 18.04 based Holoscan SDK versions will no

longer work with the Ubuntu 20.04 based Holoscan SDK v0.2.

2. To view the currently installed drivers and their version, use the query command:

$ nvgpuswitch.py query

iGPU (nvidia-l4t-cuda, 34.1.2-20220524101639)

3. To install the dGPU drivers, use the install command with the dGPU parameter (note that

sudo must be used to install drivers):

$ sudo nvgpuswitch.py install dGPU

The install command prints out the list of commands that will be executed as part of

the driver install, and then continues to execute those commands. This aids with

debugging if any of the commands fail to execute. The following arguments may also be

provided with the install command:

-h, --help show this help message and exit

-f, --force force reinstallation of the specified driver stack

-d, --dry do a dry run, showing the commands that would be

executed but not actually executing them

-i, --interactive run commands interactively (asks before running each

command)

-v, --verbose enable verbose output (used with --dry to describe

the commands that would be run)

-l LOG, --log LOG writes a log of the install to the specified file

-r [L4T_REPO], --l4t-repo [L4T_REPO]

specify the L4T apt repo (i.e. when using an apt

mirror; default is repo.download.nvidia.com/jetson)

4. The dGPU driver install may be verified using the query command:

$ nvgpuswitch.py query

dGPU (cuda-drivers, 510.73.08-1)

Quadro RTX 6000, 24576 MiB

Clara AGX –Getting Started

NVIDIA Confidential 10

5. After the dGPU drivers have been installed, rebooting the system will complete the switch

to the dGPU. At this point the Ubuntu desktop will be output via DisplayPort on the dGPU,

and so the display cable must be switched from the onboard HDMI (port 10) to DisplayPort

(port 4) on the dGPU.

6. Modify PATH and LD_LIBRARY_PATH . CUDA installs its runtime binaries such as nvcc into its

own versioned path that is not included by the default $PATH environment variable. Because

of this, attempts to run commands like nvcc will fail on dGPU unless the CUDA 11.6 path is

added to the $PATH variable. To add the CUDA 11.6 path for the current user, add the

following lines to $HOME/.bashrc after the switch to dGPU:

export PATH=/usr/local/cuda-11.6/bin:$PATH

export LD_LIBRARY_PATH=/usr/local/cuda-11.6/lib64:$LD_LIBRARY_PATH

If at any time you want to switch back to iGPU, use the install command with the iGPU

parameter:

$ sudo nvgpuswitch.py install iGPU

After the iGPU drivers have been installed, rebooting the system will complete the switch back

to iGPU. At this point the Ubuntu desktop will be output via the onboard HDMI, so the display

cable must be switched from the DisplayPort on the dGPU (4) to the onboard HDMI (10). If the

output connection isn’t switched, the terminal screen will hang during booting.

Note: The GPU settings will persist through reboots until it is changed again with

nvgpuswitch.py.

Setting up SSD Storage

Without setting up SSDK storage and moving docker storage to SSD, you might fill up the root

directory with Docker image pull operations, since a complete installation of the Jetpack leaves

only about 10GB of storage remaining in the root 32GB.

Note:

If the Clara AGX Developer Kit is reflashed with a new JetPack image, the partition table of

the m2 drive will not be modified and the contents of the partition will be retained. In this

case the Create Partition steps can be skipped, however the Mount Partition steps should

be followed again in order to remount the partition.

Any state, binaries, or docker images that persist on the m2 drive after flashing the system

may be made incompatible with new libraries or components that are flashed onto the

system. It may be required to recompile or rebuild these persistent objects to restore

runtime compatibility with the system.

Andere Handbücher für Clara AGX

Inhaltsverzeichnis

Andere Nvidia Computerhardware Handbücher

Nvidia

Nvidia Mellanox ConnectX-5 Handbuch

Nvidia

Nvidia TESLA C2050 Bedienungsanleitung

Nvidia

Nvidia BlueField-3 Bedienungsanleitung

Nvidia

Nvidia ForceWare Quadro FX 4000 SDI Bedienungsanleitung

Nvidia

Nvidia JETSON XAVIER NX Leitfaden

Nvidia

Nvidia BlueField-2 BF2500 Bedienungsanleitung

Nvidia

Nvidia TURING GPU Bedienungsanleitung

Nvidia

Nvidia TESLA M2050 Bedienungsanleitung

Nvidia

Nvidia Jetson Orin NX Leitfaden

Nvidia

Nvidia BlueField-2 BF2500 Bedienungsanleitung

Nvidia

Nvidia GeForce3 Ti200 Bedienungsanleitung

Nvidia

Nvidia TESLA C2075 Bedienungsanleitung

Nvidia

Nvidia Mellanox Bedienungsanleitung

Nvidia

Nvidia GEFORCE RTX 4090 Bedienungsanleitung

Nvidia

Nvidia FX4500 - Apple MAC Pro QUADRO FX 4500 Video Card... Kurzanleitung

Nvidia

Nvidia Mellanox ConnectX-6 MCX654106A-ECAT Bedienungsanleitung

Nvidia

Nvidia TESLA K10 Bedienungsanleitung

Nvidia

Nvidia Mellanox ConnectX-5 Bedienungsanleitung

Nvidia

Nvidia TESLA K20 Bedienungsanleitung

Nvidia

Nvidia DGX-2 SYSTEM Bedienungsanleitung

Nvidia

Nvidia TESLA K20 Bedienungsanleitung

Nvidia

Nvidia Jetson TX2 NX Bedienungsanleitung

Nvidia

Nvidia Quadro Bedienungsanleitung

Nvidia

Nvidia Jetson AGX Xavier Series Leitfaden

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung