Nvidia GeForce 2 GTS Bedienungsanleitung

nVIDIA

GeForce 2 GTS

Multimedia VGA Controller

Installation Guide

Version 1.0

06/2000

Copyrights and Liabilities

The information contained in this manual has been validated at the time of this

manual’s production. The manufacturer reserves the right to make any changes and

improvements on the product described in this manual at any time and without notice.

Consequently, the manufacturer assumes no liability for damages incurred directly or

indirectly from errors, omissions or discrepancies between the product and the

manual. All registered trademarks are the property of their respective owners.

is permitted without prior written authorization from the manufacturer.

Trademark

All products and company names are trademarks or registered trademarks of their

respective holders.

MM0GF2G-01E-00

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that

may cause undesired operation.

Notice:

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses, and can radiate radio frequency energy, and if not

installed and used in accordance with manufacturer's instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

.Reorient or relocate the receiving antenna.

.Increase the separation between the equipment and receiver.

. Plug the computer into a different outlet so that the two devices are on different

branch circuits.

. If necessary, the user should consult the dealer or an experienced radio/television

technician for additional suggestions.

Warning:

Shielded interface cables must be used in order to comply with emission limits.

Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

CSA Notice:

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus set out in the Radio Interference Regulations of the Canadian

Department of Communications.

Table of Contents

Chapter 1 Overview..................................................................1

Chapter 2 Hardware Installation.............................................3

Chapter 3 Software Installation...............................................5

Chapter 4 Display Properties for Windows..............................8

Chapter 5 Expertool for Windows..........................................13

Chapter 6 Technical Information ..........................................17

Chapter 7 Trouble Shooting...................................................19

Congratulation on the purchase of your new graphics accelerator card! You are now

the owner of a state-of-the-art video adapter that offers features and functionality

equal to, and beyond any other in its VGA class.

System Requirements

The minimum system requirements for installing the graphics card are as

follows:

¾a personal computer with a Pentium, Pentium II, Pentium III or compatible

microprocessor and at least 8MB of memory

¾a VGA analog monitor supporting a minimum 60Hz vertical refresh rate

¾an available AGP or PCI bus slot

¾a CD-ROM drive

Features

¾256Bit Graphics architecture

¾Support 2/4X AGP with Fast Write AND Execute mode

¾Integrated 350MHz RAMDAC, resolution up to 2048x1536 True Color @75Hz

¾Full acceleration for Microsoft DirectX7 and Open GL 1.2 ICD

¾2nd generation T&L Engines

¾32-bit color & 32-bit Z/Stencil buffer

¾Cube Environment Mapping

¾8 Texels Per Clock with Hypertexel

¾Order Environment Mapping

¾25M Triagngles/sec through Set-up & 1600M texels/sec.

¾DirectX Texture Compression

¾Enhanced Motion compensation for full speed DVD playback

¾Support DVI-I 1.0 Digital Flat Panel output (Optional)

¾Support NTSC/PAL TV-OUT with flicker filter (Optional)

¾S3TC Support

¾Support Video In (Optional)

¾Support VIP I/O port (Optional)

High Performance 256-bit 2D Acceleration

¾True-color hardware cursor

¾Multi-buffering for smooth animation and video playback

Chapter 1 Overview

Visually Stunning Interactive 3D

¾8 texture-mapped ,filtered ,lit texels per clock cycle

¾32-bit Z/stencil buffer (Floating point or integer)

¾32-bit ARGB rendering with destination alpha

¾High Quality Texture Filtering, including Anisotropic

¾Single pass multi-texture

High Quality HDTV/DVD Playback

¾8:1 up scaling and down scaling

¾Video acceleration for DirectShow, MPEG-1, MPEG-2 and Indeo

¾Multiple Video windows with hardware color space conversion and filtering

Software Support

¾Microsoft Windows 95/98/2000

¾Microsoft Windows NT4.0

¾DirectDraw

¾Direct3D Direct Video

¾ActiveX

Back of

computer

Static electricity can severely damage electronic parts. Take these precautions:

)Before touching any electronic parts, drain the static electricity from your body.

You can do this by touching the internal metal frame of your computer while

it's unplugged.

)Don't remove a card from the anti-static container it shipped in until you're

ready to install it. When you remove a card from your computer, place it back

in its container.

)Don't let your clothes touch any electronic parts.

)When handling a card, hold it by its edges, and avoid touching its circuitry.

Before You Begin

Before you process further, make sure your computer system meets the peripheral

requirements and switch to the standard VGA display driver.

Prepare Your Computer for Installation

Prior to working on your computer, make sure the power of the computer and any

related equipment is turned off.

Select a Vacant Expansion AGP (PCI) Slot

Most computers have a combination of AGP, PCI and ISA expansion slots. AGP

slots are usually made from plastic of a contrasting brown color (beige color), and are

shorter than other slots in your computer. Your system manual should identify the

AGP or PCI slots, as appropriate for your model. Plugging your Graphic card into

an incorrect slot could damage the card, your computer, or both. Do not try to force a

card into a slot that does not accommodate it, as it is probably the wrong slot.

ISA slot

PCI slot

AGP vs. PCI vs. ISA expansion slots

AGP slot

Chapter 2 Hardware Installation

Insert your Graphic Card

Remove the cover for the slot you intend to use and save the screw for the mounting

bracket. Then, pick up the Graphic card and position it over the expansion slot

you’ve chosen. Push the card firmly and evenly until it’s fully seated in the slot.

Replace the screw to secure the bracket of the Graphic card to the computer chassis.

Connect the Monitor/DVI (Optional)

Plug your monitor/DVI cable into the monitor/DVI connector on your Graphic card.

Make sure the other end of the monitor/DVI cable is properly connected to your

monitor/DVI.

PCI expansion

slot

Graphics card

Bracket screw

Motherboard

Monitor Connector (Blue)

AGP

expansion slot

DVI Host Receptacle Connector

)Before installing the Display driver, make sure your Windows 95/98/2000/NT

was installed in VGA mode and functions properly.

)For Windows 95 systems, please install DirectX before attempting to use the

MPEG Movie Player.

)To use an AGP graphics card with NT4.0, you may need to re-install NT with

Service Pack 3 (SP3) or later version before installing the AGP card.

)If you are running Windows NT4.0, please note that some drivers are not

compatible with earlier releases of Windows NT. Consult your dealer or local

support to ensure you have the most recent releases for Windows NT and the

drivers.

)The pictures in this chapter are only for Win98 reference.

Before You Begin

If your system is running Windows 95/98/2000/NT, the New Hardware Found

dialog box will appear after restart. Select Driver from disk provided by

hardware manufacturer, click OK, then follow all on-screen instructions. If the

New Hardware Found dialog box does not appear, follow the instructions below.

Setup VGA Mode

Click the right mouse button anywhere on the Windows 95/98/2000/NT desktop and

select Properties from the pop-up menu that appears on screen. Select Settings │

││

│

Change Display Type (For OSR2 users, please select Settings│

││

│Advanced

Properties. For Windows 98 users, please select Settings│

││

│Advanced. For

Windows NT users, please select Setting│

││

│Display Type) and then click the

[Change] button for Adapter Type. When the Select Device dialog box appears on

the screen, please select [Standard display types] from the manufacturers list and

select Standard Display Adapter (VGA) from the list of models then click OK.

Chapter 3 Software Installation

Install Software Driver

Method 1 – Automatically install VGA Driver and Applications:

1. Turn on your computer and start Windows 95/98/2000/NT.

2. Insert the Driver CD into your CD-ROM drive.

3. Click the Start button on the task bar and then select Run button.

4. Type D:\cdsetup.exe [Enter] in the Run dialog box (where D:\is the location of

your CD-ROM drive).

5. The Expertool VGA Installation dialog box will appear on the screen, please

click “Continue” button and follow the instructions on screen to complete

installation.

6. Final, restart your computer for the changes to take effect.

Method 2 – Manually install VGA Driver without Applications:

1. Turn on your computer and start Windows 95/98/2000/NT.

2. Insert the Driver CD into your CD-ROM drive.

3. Click the right mouse button anywhere on the windows 95/98/2000/NT desktop.

4. Select Properties from the pop-up menu that appears on the screen. (Figure 3-1)

5. Select Settings│

││

│Advanced in the Display Properties dialog box. (Figure 3-2)

Figure3-1 Figure3-2

6. Click the Change button for Adapter item. (Figure 3-3)

7. Click Next button in the Update Device Driver Wizard dialog box. (Figure 3-4)

Figure3-3 Figure3-4

8. Select Display a list of all the drivers in a specific location, so you can select

the driver you want check box and click Next button. (Figure 3-5)

9. Select Show compatible hardware check box and click Have Disk button.

Type the path to the folder containing the driver files and click OK. Choose the

compatible VGA Models from your Driver. Then chick Next button to continue

the installation. (Figure 3-6)

Figure3-5 Figure3-6

10. Final, restart your computer to allow the changes to take effect. (Figure 3-7)

Figure3-7

Inhaltsverzeichnis

Andere Nvidia Grafikkarte Handbücher

Nvidia

Nvidia GRID K1 Bedienungsanleitung

Nvidia

Nvidia QUADRO SYNC II Bedienungsanleitung

Nvidia

Nvidia GEFORCE GTX 550 Ti Bedienungsanleitung

Nvidia

Nvidia geforce gtx 1080 Bedienungsanleitung

Nvidia

Nvidia GeForce 8500 GT Bedienungsanleitung

Nvidia

Nvidia GEFORCE GTX 560 Ti Bedienungsanleitung

Nvidia

Nvidia Quadro Workstation Bedienungsanleitung

Nvidia

Nvidia QUADRO FX 3800 Bedienungsanleitung

Nvidia

Nvidia GeForce GTX 650 Ti Bedienungsanleitung

Nvidia

Nvidia Video-PX9000 series Bedienungsanleitung

Nvidia

Nvidia GeForce RTX 2070 SUPER Bedienungsanleitung

Nvidia

Nvidia GEFORCE GT 630 Bedienungsanleitung

Nvidia

Nvidia Quadro Bedienungsanleitung

Nvidia

Nvidia VCQK6000SYNC-PB Bedienungsanleitung

Nvidia

Nvidia GeForce MX420 Bedienungsanleitung

Nvidia

Nvidia FX1300 - Quadro FX 128MB Dual DVI-I PCIe Video... Bedienungsanleitung

Nvidia

Nvidia Titan RTX Bedienungsanleitung

Nvidia

Nvidia VCQFX4600 Handbuch

Nvidia

Nvidia Quadro FX 4700 X2 Bedienungs- und Sicherheitshinweise

Nvidia

Nvidia GeForce RTX 2080 Ti Bedienungsanleitung

Nvidia

Nvidia GEFORCE GTX 460 Bedienungsanleitung

Nvidia

Nvidia NVIDIA Quadro FX 1300 Gebrauchsanweisung

Nvidia

Nvidia Quadro FX 3700 Bedienungsanleitung

Nvidia

Nvidia 8400 - BFG GeForce GS Gebrauchsanweisung

Beliebte Grafikkarte Handbücher anderer Marken

Gainward

Gainward GeForce GTX 690 4GB Bedienungsanleitung

ATI Technologies

ATI Technologies RADEON 137-40225-20 Bedienungsanleitung

MSI

MSI N220GT series Bedienungsanleitung

ATI Technologies

ATI Technologies RADEON 7000 MAC EDITION Bedienungsanleitung

SIIG

SIIG aurora Bedienungsanleitung

ClearSpeed

ClearSpeed ClearSpeed Advance e720 Bedienungsanleitung

MSI

MSI R7850 series Bedienungsanleitung

DVS

DVS Atomix HDMI Bedienungsanleitung

Aztech

Aztech VGS3D-AGP Bedienungsanleitung

Advoli

Advoli TB4 Standard Bedienungsanleitung

ELSA

ELSA ERAZOR III LT Bedienungsanleitung

Gigabyte

Gigabyte GV-R7500L Bedienungsanleitung

Themis

Themis TGA-7000 PMC Bedienungsanleitung

EMS

EMS XtremeRGB-Ex1 Bedienungsanleitung

Pioneer

Pioneer PDA-5003 Bedienungsanleitung

QDI

QDI N2 Bedienungsanleitung

NEC

NEC N8116-48 Bedienungsanleitung

MSI

MSI R7770 PoweR Edition Bedienungsanleitung