NVision Junior RacerRTF Gebrauchsanweisung
Junior Racer RTF
Quick start manual
catalog
Product Include........................................................................................... 1
Operate Junior Racer Whoop Drone..........................................................2
Power On/Off..................................................................................2.1
Battery...............................................................................................2.2
Charge...............................................................................................2.3
F411 12A AIO FC.......................................................................................... 3
Description..........................................................................................3.1
Wiring..................................................................................................3.2
Operate the radio........................................................................................4
Power On/Off.................................................................................... 4.1
LED Indicator and Buzzer.............................................................. 4.2
Binding the Receiver......................................................................4.3
Switching Protocol.........................................................................4.4
Charging............................................................................................ 4.5
NVISION VTX................................................................................................5
Description..........................................................................................5.1
Wiring..................................................................................................5.2
Junior Racer Whoop Drone include
1x Junior Racer(with Frsky XM+ Receiver)
1x Radio(support Frsky XM+)
1x fpv goggles
1x B3 Chager
1x 300mAh 3S 45C Battery
2x Lipo Battery Strap
1x Props Removal Tool
2x fpv goggles Dipole 5.8G Antennas
1x GEMFAN 1636 4-blade Propeller(4pcs)
1x Nylon Cable Tie(5pcs)
1x M1.4*6mm Screw(6pcs)
Operate Junior Racer Whoop Drone
*Power On/Off: connect the power cable of to Junior Racer 75 the battery, the
power LED, receiver LED and FC LED are on, then the FC LED flashes and the receiver
LED turns off. After using, unplug the connection, and all LED will turn off.
*Battery: connect the battery to the voltage tester to display the current voltage
value of the battery.
*Charge: connect the battery to the charger supplied with the adapter or other 5V
power. The LED will show red light when charging; the LED will show green light
when finishing charging.
F411 12A AIO FC
FC Parameters:
CPU: STM32F411CEU6
Six axis: MPU6000 (SPI connection)
Size: 29mmx29mm
Firmware version: Betaflight TCMM-F411
RC sharing: UART1-RX
OSD: Built-in Betaflight OSD (STM32 controls the OSD chip through SPI in DMA
mode)
Receiver: Support FrskyXM/XM+ receiver/Futaba receiver/Flysky receiver/TBS
Crossfire receiver
Support programmable LED such as WS2812
Built-in current sensor
Reserved buzzer interface
Reserve DJI port
Weight: 5.07g
ESC Parameters:
Support: PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600
Input voltage: 2S-4SLipo
Continuous current: 12A
Peak current: 20A
Firmware: BLHELI_S
Processor: SILABSEFM8BB21F16G
Motor connector: 1.25mm pin header connector
LED Status
Reason
solution
Power LED off
1.Insufficient battery 2.FC
is broken
1. Charge the battery 2.
Replace the FC
FC LED off and Receiver
LED solid
FC is broken
Replace the FC
FC LED flashes Bule at
high frequency
Out of control or BB
ringing mode enabled
There are many reasons,
and the reasons need to
be investigated step by
step
FC LED flashes Red at
high frequency
Low battery voltage
Replacement battery
FC LED flashes Bule at
Slow flashing
normal
Operate the radio
Power On/Off
POWER ON: Long press the power button on the transmitter for 3 seconds until it beeps three ti
mes then release. The remote control radio transmitter power indicator will quickly flash red, the
n remain blue.
POWER OFF: A long press of the power button on the remote control radio transmitter will turn
it off after three beeps.
LED Indicator and Buzzer
The LED light indicates the working status of the radio transmitter.
State of the LED
Camera status
Solution
Red light normally on
The throttle joystick or switches are not in the lowest
Lower throttle and switch to the
lowest position. Turn to blue
then.
Red light flashing quickly
The radio transmitter is binding
Wait for completing binding
Blue light flashing slowly
Battery reaches the low voltage limit
Charge the transmitter batteries
The buzzer will alarm three times in a row, which indicates a low battery and needs to be re-charged.
Binding the Receiver
There are the steps to make the LiteRadio 2 SE enter binding status.
1.Power on the remote control radio transmitter and wait for its system to load completely.
2.Press the bind button on the back of the remote control radio transmitter. The power indicato
r will flash red.
3.If binding is successful, the LED light will change to blue. If not, repeat the process above.
Switching Protocol
The Frsky version could support 4 different protocols, including Frsky D16 FCC, Frsky D16 LBT,
Frsky D8, and Futaba S-FHSS. The protocol is indicated by the flashing times of the red LED when
power on, before the buzzer alarms.
LED Status
Protocol Version
Flash once
Frsky D16 FCC
Flash twice
Frsky D16 LBT
Flash Three Times
Frsky D8
Flash Four Times
Futaba S-FHSS
Power the radio transmitter off; To change protocols (Frsky FCC D16, Frsky D16 LBT, Frsky D8, or
Futaba S-FHSS), here are the steps:
1.Press and hold the BIND button while powering the radio transmitter back on;
2.Then the flash times of the red LED before buzzer alarms will change, according to the tables a
bove
Charging
The remote control radio transmitter has a built-in 1000mAh battery. It indicates a low battery
and needs to be re-charged if the blue light flashes slowly. Below charging method for reference:
Turn off the remote control radio transmitter.
Plugin remote control radio transmitter with adapter by USB cable (5V output adapter is
allowed).
The LED button red means charging, while light off means fully charged.
The continued working time for a fully charged battery is about 8 hours.
NVISION A01 VTX
Description:
*Switchable power includes 0mW, 25mW and 200mW.
*This VTX includes SmartAudio function. The flight controller can use the audio
cable to communicate with the video transmitter. It allows the flight controller to
know the frequency used by the VTX and make changes.
*This VTX supports PitMode.
*Dipole whip high sensitivity antenna. It is mounted to the VTX board durable.
*Output power: 0mW, 25mW and 200mW (adjustable)
*Power supply voltage: 5V. Does not support direct connection to 1S battery
*Weight: 2.0g
*Frequency: 5.8GHz 6 frequency band 48 channels, competition frequency band:
5362~5945MHz
Component Layout Diagram for NVISION A01 VTX:
How to Change Frequency & Channel & Power
Only support frequency and power change through the SmartAudio interface.
Method 1: Use the OSD menu.
Enter the OSD menu by radio transmitter sticks ( Pitch Stick UP and Yaw Stick Left). Then
FEATURES -> VTX SA to change the frequency and power.
Inhaltsverzeichnis
Andere NVision Drohne Handbücher
