OAI TRI-SOL Bedienungsanleitung

OPERATION MANUAL

TRI-SOL

SOLAR SIMULATOR

1-1.6KW

685 RIVER OAKS PARKWAY

SAN JOSE, CA 95134

www.oainet.com

[email protected]

408/232-0600

P/N 0131-7024-01 Rev. D

01/21/14

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 1

TRI-SOL SOLAR SIMULATOR

Definitions of the following Symbols and Words should be understood

before working with this manual and/or the equipment with this

manual.

The definitions are:

“Caution”- Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury.

“Warning”- Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

“Danger”- Indicates an eminently hazardous situation which, if not

avoided, will result in death or serious injury.

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 2

TABLE OF CONTENTS

PURPOSE, SCOPE AND REVISION HISTORY...................................................3

SECTION 1: INTRODUCTION .............................................................................5

1.1. GENERAL DESCRIPTION…………………………………………...……….5

1.1.1. SOLAR SIMULATION LIGHT SOURCE SYSTEMS……………..….5

1.2 APPLICATION....……………………………..……….…………….…...……...6

1.3 GETTING HELP…..…………………………………………………….………7

SECTION 2: RECEIVING AND UNPACKING THE EQUIPMENT….…...………..8

2.1 CHECK SHOCK WARNING LABEL.........................................................8

2.2 OPEN CRATE AND UNPACK EQUIPMENT……………………………….9

SECTION 3: SAFETY PRECAUTIONS..............................................................10

3.1 HAZARDS TO PERSONNEL………..………………………………………10

3.1.1 UV HAZARD BURN.……………………………………………………11

3.1.2 HEAT BURN HAZARD....................................................................11

3.1.3 HAZARDS DUE TO LAMP EXPLOSION ........................................11

3.1.4 HAZARDS DUE TO ELECTRICAL SHOCK....................................12

SECTION 4: LAMP INSTALLATION AND CLEANING.....................................13

4.1 INSTALL OR CHANGE THE LAMP..………………………………………13

4.2 ADJUSTING THE LAMP POSITION………...……………………………. 17

4.3 CLEANING OPTICAL COMPONENTS...................................................17

4.4 INSTALLING THE AIR MASS FILTER...................................................18

SECTION 5: SYSTEM OPERATION..................................................................19

5.1 STARTING AND OPERATING THE SOLAR SIMULATOR ...................19

5.2 MEASURING UNIFORMITY ...................................................................23

5.3 ADJUSTING UNIFORMITY.....................................................................24

5.4 OPERATING THE SOLAR SIMULATOR REMOTELY...........................25

SECTION 6: SYSTEM INTERLOCKS................................................................27

6.1 SOLAR SIMULATOR INTERLOCKS.......................................................27

6.1.1 THE PERSONAL SAFETY INTERLOCK .........................................28

6.1.2 THE AIR-FLOW SYSTEM SAFETY INTERLOCK............................28

SECTION 7: HAZARDOUS MATERIALS USED WITH THE SYSTEM .............29

7.1 ISPROPYL ALCHOL................................................................................29

SECTION 8: SYSTEM SPECIFICATIONS AND DRAWINGS............................30

8.1 SYSTEM SPECIFICATIONS...................................................................30

8.2 SYSTEM DRAWINGS.............................................................................30

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 3

PURPOSE SCOPE AND REVISION HISTORY

PURPOSE. To provide instructions on how to receive/ship, install, handle, use,

trouble-shoot and maintain the UV LIGHT SOURCE hereinafter referred to as the

EQUIPMENT.

SCOPE. The user of this document should have a complete understanding of

the EQUIPMENT.

OBJECTIVE. To ensure that this document provides as much information as

possible on the Equipment so that few, if any, questions will be raised relative to

its operation and functionality over the short and long-term.

REVISION HISTORY.

Purpose Rev

Level Release

Date

New Release ECO 10670 A 10/06/10

Change Company Logo & Text Colors, Updated Lamp Instr. ECO

10826 B 07/07/11

Add Constant Intensity operation description, ECO 10867 C 08/11/11

Add section 4.4 Installing the Air Mass Filter per ECO 11359 D 01/21/14

The Remainder of This Page is Intentionally Left Blank

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 4

No part of this publication may be reproduced, transmitted, transcribed, stored in

a retrieval system or translated into any language or computer language, in any

form or by any means, electronic, mechanical, magnetic, optical, chemical,

manual or otherwise, without the prior written permission of OAI.

Disclaimer:

OAI makes no representations or a warranty with respect to the contents hereof

and specifically disclaims any implied warranties or merchantability or fitness for

any particular purpose. Further, OAI reserves the right to revise this publication

and to make changes from time to time in the content hereof, without obligation

of OAI to notify any person of such revision or changes.

WARNING!

The high intensity energy produced by systems employing xenon arc lamps can

cause serious eye or skin damage. Personnel working with this equipment

must wear eye protection with suitable filtration to block ultraviolet and infrared

radiation, and avoid directly exposing skin for extended periods. OAI will not be

responsible for injuries arising from incorrect or unprotected work with these

Light sources. They should not be adjusted or serviced by personnel lacking

specific training on them. Before installing or operating this equipment, be sure

to read Section 3, on safety. Due to the high voltage to start xenon arc lamps, the

light source power supply starter circuit may create RF noise during the start up

cycle that might possibly have an effect on sensitive electronic equipment in the

immediate area. Noise may also be created on the power supply AC input line

during the start up cycle. To eliminate this potential problem, it is recommended

that the power supply and lamp be started before turning on any sensitive

electronics in the immediate area. If this is not possible, it is also recommended

that the power supply and cabling be placed at a distance from any sensitive

electronics that has not been adequately shielded.

Before installing or operating this equipment, be sure to read

Section 4, SAFETY PRECAUTIONS

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 5

SECTION 1:

INTRODUCTION

This manual is intended to provide instructions and recommendations for the

proper use and maintenance of the EQUIPMENT.

1.1 GENERAL DESCRIPTION

1.1.1 SOLAR SIMULATION LIGHT SOURCE SYSTEMS

Solar simulation light sources produce an intense, uniform, collimated beam of

broad band energy. The radiation from the xenon arc lamp is collected by an

ellipsoidal reflector and directed to an aluminum “turning” mirror. The beam

converges onto the optical integrator made up of arrays of 49 or more closely-

spaced lenses. The exit beam diverges through the open shutter to the second

mirror, where it is reflected through the output (collimating) lens onto the

exposure plane. The light is filtered to match the required solar spectrum just

after it exits the optical integrator.

Controls for adjusting the lamp’s position within the main reflector housing are

located inside one of the access doors of the light source system. Typically,

power for the blower, shutter, lamp power supply and accessories is supplied via

a multi-conductor cable which is located on the rear of the housing.

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 6

1.2 APPLICATION

The EQUIPMENT is designed to emit collimated broad band light. OAI’s Tri-Sol

Solar Simulator Systems are high performance systems intended for solar

simulation, with applications including solar cell testing and weathering.

The Remainder of This Page is Intentionally Left Blank

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 7

1.3 GETTING HELP

Assistance in answering questions relating to the operation of the EQUIPMENT

can be obtained by calling OAI’s customer support at 1 (408) 232-0600 between

the hours of 8:00 A.M. and 5:00 P.M., Pacific Standard Time. Outside normal

business hours, or at any other time, written questions may be Faxed to 1 (408)

433-9904 to the attention of the Optical Products Group Customer Support, or

emailed to [email protected].

The Remainder of This Page is Intentionally Left Blank

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 8

SECTION 2:

RECEIVING AND UNPACKING THE

EQUIPMENT

Normal receiving inspection procedures should be followed prior to unpacking

the EQUIPMENT including the inspection of the Shock Warning label on the front

of the crate.

Then, use a copy of these guidelines when ready to unpack and prepare the

Equipment for installation. Be sure to follow all safety precautions used during

the handling of packaging and related materials.

2.1 CHECK SHOCK WARNING LABEL

The color of the liquid capsule on the Shock Warning label affixed to the side of

the SOLAR SIMULATOR crate (shown in Figure 3-1) should be clear; if it’s red,

the shipment should be inspected for physical damage. If damage is found,

reject the shipment.

The Remainder of This Page is Intentionally Left Blank

Figure 3-1. Warning label, straps and clips

on front of crated Solar Simulator.

Check per

para. 3.1

Remove

clips.

Cut straps using

metal shears.

Manual PN: 0131-7024-01, Rev: D MANUAL MDL TRI-SOL 1-1.6KW SOLAR SIM OPER 9

2.2 OPEN CRATE AND UNPACK EQUIPMENT

CAUTION! WEAR SAFETY GLASSES AND GLOVES AS

PROTECTION FROM CUTS OR DAMAGE TO EYES WHEN

CUTTING STRAPS AND REMOVING CLIPS!

1) If the shipment is accepted, cut and remove any straps securing

the crate to the pallet (shown in Figure 3-1).

2) Remove any bolts along the bottom of the front of the crate.

3) If clips are used on the crate, use one hand loosely cupped over

each clip to prevent damage to the eyes, pop off the clips around

the edges of the front of the crate (shown in Figure 3-1). Use either

the claw side of a hammer or a screwdriver to loosen same.

Note: Some of the crated items are very heavy. Use proper

lifting techniques when handling this unit

Inhaltsverzeichnis

Andere OAI Industrieanlagen Handbücher

OAI

OAI 200 Series Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Rioned

Rioned UrbanJet Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung