Oakton TDS 1 Bedienungsanleitung

TDS 1 Pocket TDS Tester

Instruction Manual

OAKTON INSTRUMENTS

www.4Oakton.com

v2.1

TDS 1 Pocket TDS Tester Instruction Manual

1. Battery Installation

Please install batteries according to the following steps. Please note polarity:

“+”(positive) is upward; “-” (negative) is downward

2. Keypad Functions

■Short press------- < 2 seconds

■Long press-------- > 2 seconds

1. Short press to turn on, long press to turn off;

2. When turned off, long press to enter setup;

3. In mode setting, short press to change

parameter;

1. When turned on, long press to enter

calibration mode.

2. In calibration mode, short press to confirm

calibration;

3. In mode setting, short press to confirm

parameter selection.

Diagram - 1

3. Calibration

3.1 Rinse the probe in distilled water and dry it. Short press to

turn on the tester.

3.2 Long press to enter calibration mode; Short press to exit.

3.3 Dip the probe into 1413 µS calibration solution. Stir gently, leave it to stand,

LCD displays (Diagram 3), short press to complete 1-point calibration.

The tester returns to measuring mode, and calibration icon appears at the

button left of LCD.

3.4 Rinse probe in distilled water and dry it. Follow the steps in 4.2-4.3 to

complete 2nd point calibration in 12.88 mS calibration solution, tester returns to

measuring mode, calibration icons display on bottom left of LCD.

4. TDS Measurement

4.1 Short press to turn on tester. Rinse probe in distilled water and dry it.

4.2 Stir probe in the sample solution gently, leave it to stand. Get readings after

the smile icon comes up and stays.

5. Notes

5.1 The tester adopts 1413 µS and 12.88 mS standard calibration solutions. Users

can use 1-2 point calibrations as needed. For most circumstances, calibrating in

1413 µS to complete 1st point calibration will meet testing requirements.

5.2 The tester has self-diagnosis functions:

Symbol

Self-Diagnosis information

How to fix

Wrong calibration solution,

which exceeds the

recognizable range of the

meter.

1. Check if calibration solution is

correct

2. Check if probe isdamaged.

Diagram - 3

is pushed before

measurement is stable

( comes up)

Wait for the smile icon to stay,

and then short press

5.3 The tester has already been calibrated after manufacture. Usually users can

use the tester right away, or test it in the calibration solutions to test its

accuracy. When error is large, calibrate it before using.

5.4 We recommend replacing new calibration solutions after 5-10 times of

calibrations to keep the solution’s accuracy.

6. Parameter Setting

6.1 Parameter setting reference chart:

Symbol

Parameter Setting Items

Code

Factory Default

TDS Factor

0.40 to 1.00

0.71

Restore to factory default

No –Yes

6.2 How to setup parameters:

When turned off, long press to enter setup →short press to switch

P1-P2→Short press , parameter flickering→short press to choose,

short press to confirm parameter selection→Long press to switch off.

6.3 Parameter setting notes

a) TDS Factor (P1):

Users can adjust TDS Factor by experimental data or experience. The

following chart lists some commonly used TDS Factors for reference.

Conductivity and TDS Factor

Conductivity of the solution

TDS Factor

0~100 μS/cm

0.60

100~1000 μS/cm

0.71

1~10 mS/cm

0.81

10~100 mS/cm

0.94

b) Restore to factory default:

Select Yes to restore the calibration to the theoretical values and parameter

setting to original values. When meter’s calibration or measurement performs

abnormally, this function can be adopted so the meter goes back to factory

default setting and then users can conduct calibration or take measurements

again.

7. Technical Specifications

TDS

Range

0–100.0 ppm, 0–1000 ppm, 0–

10.00 ppt

Resolution

0.1/1 ppm, 0.01 ppt

Accuracy

±1% F.S

Calibration points

1-2 points

Automatic Temp.

Compensation

0-50˚C

Temp.

Range

0-50˚C

Resolution

0.1˚C

Accuracy

±0.5˚C

8. Other Functions & Parameters

Indication of

calibration points

Auto Power-

off

Power-off in 8

minutes if no

operation

Indication of stable

measurements

Waterproof

level

IP67, floats on water

Self-Diagnosis

information

Er1, Er2

Power Supply

AAA batteries*4

Low battery

reminder

Flashes to

remind to replace

batteries

Battery Life

1000 hours

Dimensions/Weight

Instrument: 40*31*178mm/107g; Carrying case:

190*165*140mm/438g

9. Warranty

We warrant this instrument to be free from defects in material and workmanship

and agrees to repair or replace free of charge, at option of OAKTON INSTRUMENTS,

any malfunctioned or damaged product attributable to responsibility of OAKTON

INSTRUMENTS, for a period of two years from the delivery (a six-month limited

warranty applies to probes). This warranty does not apply to defects resulting from

actions such as misuse (violation of the instructions in this manual or operations in

the manner not specified in this manual), improper maintenance, and unauthorized

repairs. Warranty period is the time limit to provide free service for the products

purchased by customers, not the service life of the tester or probe.

Oakton Instruments reserves the right to update the information in this manual without giving notice in

advance.

OAKTON INSTRUMENTS

PO Box 5136

Vernon Hills, IL. 60061

Tel: 888-462-5866

www.4Oakton.com

Inhaltsverzeichnis

Andere Oakton Prüfgeräte Handbücher

Oakton

Oakton Salt 1 Bedienungsanleitung

Oakton

Oakton EcoTestr CTS1 Bedienungsanleitung

Oakton

Oakton TempTestr 35628-00 Bedienungsanleitung

Oakton

Oakton Eutech Instruments TDSTestr11+ Bedienungsanleitung

Oakton

Oakton pHTestr 30 Bedienungsanleitung

Oakton

Oakton CTS5 Bedienungsanleitung

Oakton

Oakton pHTestr 20 Bedienungsanleitung

Oakton

Oakton PCTS5 Bedienungsanleitung

Oakton

Oakton ORP5 Bedienungsanleitung

Oakton

Oakton pHTestr 30 Bedienungsanleitung

Oakton

Oakton EcoTestr EC1 Bedienungsanleitung

Oakton

Oakton ORPTestr 30 Bedienungsanleitung

Oakton

Oakton WD-35662-35 Bedienungsanleitung

Oakton

Oakton EcoTestr pH 2 Bedienungsanleitung

Oakton

Oakton EC1 Bedienungsanleitung

Oakton

Oakton PCTSTestr 50 Bedienungsanleitung

Oakton

Oakton pHTestr 1 Bedienungsanleitung

Oakton

Oakton ORPTestr10 Bedienungsanleitung

Oakton

Oakton pHTestr 30 Bedienungsanleitung

Oakton

Oakton CTSTestr 50 Bedienungsanleitung

Oakton

Oakton pHTestr 1 Technisches Handbuch

Oakton

Oakton WD-35634-06 Bedienungsanleitung

Oakton

Oakton CTSTestr 5 Bedienungsanleitung

Oakton

Oakton pH BNC 10 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung