Oce CS550 Pro Bedienungsanleitung
o
Océ CS550/CS6xx Pro
Calibration
Océ User Manual
Océ-Technologies B.V.
© 2009 Océ
All rights reserved. No part of this work may be reproduced, copied, adapted, or transmitted
in any form or by any means without written permission from Océ.
Océ makes no representation or warranties with respect to the contents hereof and specifi-
cally disclaims any implied warranties of merchantability or fitness for any particular purpose.
Further, Océ reserves the right to revise this publication and to make changes from time
to time in the content hereof without obligation to notify any person of such revision or
changes.
Edition: 2009-03
Contents
Chapter 1
Introduction.........................................................................................................5
Basic system configuration.......................................................................6
Why calibration...........................................................................................7
Main steps in calibration...........................................................................8
Chapter 2
Check the print quality.......................................................................................9
2.0 Check the print quality.......................................................................10
Chapter 3
Controller calibration........................................................................................11
3.1 Calibrate the EFI controller................................................................12
3.1 Calibrate the Creo controller.............................................................17
3.1 Calibrate the Océ PRISMAsync controller........................................20
3.2 Check the print quality.......................................................................28
Chapter 4
Printer calibration.............................................................................................29
4.1 Perform the adjustment operation...................................................30
4.2 Adjust the white point (gamma offset).............................................33
4.3 Calibrate the EFI controller................................................................39
4.3 Calibrate the Creo controller.............................................................44
4.3 Calibrate the Océ PRISMAsync controller........................................47
4.4 Check the print quality.......................................................................55
3
Contents
4
Contents
Chapter 1
Introduction
o
Basic system configuration
The basic system configuration contains the following parts.
■Printer
■Controller
■Scanner.
The basic system configuration has one of the following controllers
■Fiery ® PRO80/S450 65C-KM Color Server (IC303/IC305), default including a
photo spectrometer
■Creo controller, IC304/IC304 Plus, default including a photo spectrometer
■Fiery ® X3e TY2 65C-KM (embedded controller (IC408) for which a photo spectrom-
eter is optional.
■Océ PRISMAsync controller (Océ CS655 and Océ CS665 only) for which a photo
spectrometer is optional.
You can only calibrate a controller if you have a photo spectrometer.
Note:
Do not use the ColorCal / Off-the-glass method as described in the controller documen-
tation.
Chapter 1 - Introduction6
Basic system configuration
Why calibration
The printer is calibrated for a screen at installation and at every next service visit. The
default screen is Dot 1. The Océ CS550/CS6xx Pro will hold on to the calibrated level
of print quality by automatically performed adjustments. In normal circumstances there
is no need to do additional calibrations.
External circumstances, for example temperature, humidity and consumables change over
time. These changes effect the colour reproduction. You can perform a calibration as de-
scribed in this document to eliminate the effect of the external circumstance on the colour
reproduction.
There is no need or use to calibrate the scanner.
Chapter 1 - Introduction 7
Why calibration
Main steps in calibration
#
Sub-stepMain step
‘2.0 Check the print quality’ on page 101. Check the print quality
Continue only if the colour reference chart does not meet your requirements.
‘3.1 Calibrate the EFI controller’ on page 12
or
‘3.1 Calibrate the Creo controller’ on page 17
or
‘3.1 Calibrate the Océ PRISMAsync controller’ on page
20
2. Calibrate the controller
‘3.2 Check the print quality’ on page 28
The result of the controller calibration as checked in 3.2 normally meets the required
print quality. If the print quality still does not meet your requirements, you can
consider to proceed with the printer calibration.
‘4.1 Perform the adjustment operation’ on page 30 1
3. Calibrate the printer
‘4.2 Adjust the white point (gamma offset)’ on page 33
1
‘4.3 Calibrate the EFI controller’ on page 39 2
or
‘4.3 Calibrate the Creo controller’ on page 44 2
or
‘4.3 Calibrate the Océ PRISMAsync controller’ on page
472
‘4.4 Check the print quality’ on page 55
Note:
1 Calibration of your copy process only requires step 4.1 and 4.2.
Note:
2 Calibration of the printer requires calibration of the controller because the controller
takes the printer settings into account at controller calibration.
Chapter 1 - Introduction8
Main steps in calibration
Chapter 2
Check the print quality
o
2.0 Check the print quality
Introduction
You can print the Océ Color Reference chart to check the print quality. You can download
the print files used in this document form the Océ website. Before you print this chart,
you need to warm up the machine.
Before you begin
Load the A4/Letter portrait reference media with the correct paper settings.
Load the A3/Tabloid reference media with the correct paper settings.
Note:
Reference media is the media that you use mostly (bulk). The Océ reference media is
Océ Top Color 90 g/m2.
Warm up the printer
1. Print the file 'Océ Startup Page.pdf'.
Result
The Océ CS550/CS6xx Pro is warmed up and ready to evaluate the print quality.
Print the Océ Color Reference chart
1. Print the file 'Océ Color Reference Chart.pdf'.
Result
The result is a printed Océ Color Reference chart to evaluate the print quality.
Chapter 2 - Check the print quality10
2.0 Check the print quality
Inhaltsverzeichnis
Andere Oce Multifunktionsdrucker Handbücher
Oce
Oce VarioPrint 2045-65 DC Bedienungsanleitung
Oce
Oce image runner 1025 Bedienungsanleitung
Oce
Oce im5530 Konfigurationshandbuch
Oce
Oce cm3522 Bedienungsanleitung
Oce
Oce im5530 Programmierhandbuch
Oce
Oce VarioLink 2222c Bedienungsanleitung
Oce
Oce VarioLink 5022 Bedienungsanleitung
Oce
Oce fx2081 Bedienungsanleitung
Oce
Oce cm4521 Bedienungsanleitung
Oce
Oce VarioLink 5022 Bedienungsanleitung
Oce
Oce im4512 Bedienungsanleitung
Oce
Oce VL3622 Bedienungsanleitung
Oce
Oce cx2100 Bedienungsanleitung
Oce
Oce CM4520 Bedienungsanleitung
Oce
Oce VarioLink 9522 Bedienungsanleitung
Oce
Oce im2330 Konfigurationshandbuch
Oce
Oce im2330 Bedienungsanleitung
Oce
Oce OP1030 Bedienungsanleitung
Oce
Oce OP33 Bedienungsanleitung
Oce
Oce im5530 Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
