Ocean Blue 400200 Einrichtungshandbuch

SAVE THESE INSTRUCTIONS

DEALER/INSTALLER: GIVE TO HOMEOWNER

Ocean Blue

Above Ground A-Frame Pool Ladder

Assembly and Installation Manual

Part no. 400200

Not for Use

with Soft

Sided Pools

- 1 -

Ocean Blue A-Frame Ladder

for above ground pools

Tools Needed for Assembly

■Rubber Mallet

■Cordless Drill w/Phillips

Driver

■5/16” Drill Bit

■Phillips Screwdriver

Parts List

■4 - Side Rails

■4 - Handrails

■1 - Platform

■2 - Right Adjustable Rail Boot

■2 - Left Adjustable Rail Boot

■2 - Swing-up Rails

■3 - Swing-up Treads

■1 - Bottom Swing-Up Tread

■6 - Fixed Ladder Treads

■1 - Anti-Swim Barrier

■1 - Anti-Swim Barrier Extension

■1 - Fixed Ladder Tread

■1 - Hardware Safety Pack

Hardware Bag

■20 - 1/4-20 hex nuts

■2 - 1/4-20 x 1.25” Philips pan

head screws

■8 - 1/4-20 x 1.5” Philips pan head

screws

■8 - 1/4-20 x .625” Philips pan

head screws

■4 - 1/4-#10 x .75” Philips self-

tapping screws

■2 - 1/4 - 20 x 3-1/2” Bolts

■2 - 1/4” Flat Washers

■1 - Strip of Foam Pads (4 pads)

■Instructions

■Warning Labels

■Padlock

4 – Handrails

2 – Swing-up Rails

1 - Platform

6 - Fixed Ladder

Treads

2 - Right

Adjustable

Rail Boots

1 - Anti-Swim

Barrier

1 - Bottom

Swing-Up Tread

3 - Swing-up

Treads

1 - Hardware/Safety Pack

1 - Anti-Swim

Barrier Extension

2 - Left Adjustable

Rail Boots

4 - Side Rails

ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY

- 2 -

Tools Needed: Rubber Mallet

Step #1

#1: Lay out the Swing-up

Rails and Swing-up Treads as

shown.

NOTE: The bottom Swing-up

Tread has a“house shaped”

tab and is positioned at the

bottom of the Swing-up Rail.

#3: Place the remaining Swing-up

Rail over the tabs of the Swing-up

Treads and tap into place using the

rubber mallet. Set this assembly

aside.

#1: Slip one of the Adjustable Rail

Boots over the end of a Side Rail.

It will need to be all the way on

if the outside dimension of your

pool is 50” or

backed off to

the marked

number that

corresponds

with the height

of your pool.

#2: Using two 1/4-20 x 1 1/2” long

bolts and two 1/4-20 hex nuts,

fasten the Adjustable Rail Boot to

the Side Rail. Repeat for remaining

three Side Rails.

Step #3 continued

Step #2

Tools Needed: Rubber Mallet, cordless drill with Phillips bit.

#2: Using a rubber mallet, tap the

Swing-up Treads into place.

Adjustable Rail Boots are not required if the outside height of your pool

(measured from the ground to the top of the pool ledge) is 48”or less. If

this measurement is more than 48”rail boots will be required. If the out-

side measurement of your pool is 48” or less, skip to step 3.

#1: Overlap the at end of the

Handrail onto the top of the Side

Rail. Using two 1/4 - 20 x 5/8” bolts

and two 1/4- 20 hex nuts, attach the

Handrail to the Side Rail. Repeat for

the remaining three Side Rails.

Step #3

Tools Needed: Rubber Mallet, cord-

less drill with Phillips bit.

- 3 -

Step #3 continued

#2: Lay one of

the Side Rail

assemblies on a

at surface.

Matching the

tabs in the Fixed

Ladder Treads

to the notches

in the Side Rail

assembly, use

the rubber mallet to tap the treads

into place.

#3: Placing your foot on the Side

Rail to hold it steady, use the rubber

mallet to tap down the Fixed Ladder

Treads until they are rmly seated

in the Side Rail.

#4: Place the opposite Side Rail

assembly on top of the Fixed

Ladder Treads so that the notches

and tabs align and tap it into place.

Placing your foot on the Side Rail

to hold it steady, use the rubber

mallet to tap down the Fixed Ladder

Treads until they are rmly seated

into both Side Rails.

#5: With ladder assembly on edge,

position one of the remaining Fixed

Ladder Treads so that the tabs

align with the notches at the bottom

of the Side Rail assemblies and tap

in with the rubber mallet until the

tread is properly seated.

#6: Using the openings opposite

the tabbed end, slide the Platform

over the two Handrails.

#7: Using the rubber mallet, tap

the Platform down until seated on

the lugs on the Side Rails.

- 4 -

Step #4

Tools Needed: Rubber Mallet, cordless drill with Phillips bit.

#1: Lay the Anti-Swim Barrier and

the Anti-Swim Barrier Extension on

a at surface.

#2: Position the Anti-Swim Barrier

Extension over the Anti-Swim Bar-

rier so that the length of the Barrier

matches the length from the top

tread to the bottom tread of the

ladder. Attach with two 1/4 - 20 x 1

1/4” bolts and two 1/4- 20 hex nuts.

#3: Using the rubber mallet, tap

the Anti-Swim Barrier into place.

#4: Evenly space the foam

adhesive pads to the Barrier.

#1: Flip entire ladder assembly

onto its side. Slide the two remaining

Side Rail assemblies through

the two openings on the tabbed end

of the Platform. Using the rubber

mallet, tap down on the Platform

until it is seated against the lugs

on the Side Rails. IT MAY REQUIRE SEVERAL HARD BLOWS WITH

A RUBBER MALLET TO SEAT THE PLATFORM ALL THE WAY DOWN

ONTO LUGS.

Step #5

Tools Needed: Rubber Mallet, cordless drill with Phillips bit.

Step #5 continued

- 5 -

Step #5 continued

#4: Stand the ladder upright.

Attach the Swing Ladder assembly

by exing the oval openings over

the two round tabs on the Platform.

#3: Position the remaining Fixed

Ladder Tread so that the tabs align

with the notches at the bottom of

the Side Rail assemblies and tap in

with the rubber mallet until the tread

is properly seated. NOTE: The small

groove should face the inside of the

ladder.

#5: Using the

rubber mallet tap

down to secure.

#2: Using two #10 x 3/4” self-

tapping screws, connect the Hand-

rails together by using one screw

on the outside and one screw on

the inside. Repeat for the remaining

handrail.

- 6 -

Tools Needed: Cordless drill with Phillips bit.

#1: Carefully lift the ladder over the pool wall

making sure the Swing Ladder is on the outside

of the pool. Be careful not to damage liner or

pool wall. The platform must be level should

rest on the pool top seat and the bottom tread

should rest rmly on the pool bottom. Depend-

ing on the outside height of the swimming pool

ledge, rail boots may need to be readjusted at

this time. Use of a ladder pad is highly

recommended to protect pool liner.

#2: Tip the ladder sideways to allow the treads

to ll the water. This will prevent oating. Allow

ladder to ll with water until it settles on the

bottom of the pool. Small holes in the side rails

will let the water in. this may take a few minutes.

#3: Check to make sure the hole

locations in the platform are clear

of pool wall and supports. Drill two

5/16” holes through the Platform

and pool ledge. Fasten the ladder

platform to the pool ledge using two

¼-20 x 2-1/4” bolts, ¼-20 hex nuts.

You MUST secure the ladder to

the pool top rail for strength and

stability.

Step #5

Placing A-Frame Ladder in Pool

CHOOSE A LOCATION THAT IS LEVEL AND IN FULL VIEW.

POOL MUST HAVE COMPETENT ADULT SUPERVISION AT ALL TIMES WHEN IN USE.

OUTSIDE TREADS MUST

BE IN THE UP POSITION

AND LOCKED AT ALL

TIMES WHEN POOL IS

NOT IN USE.

Step #6

#4: When the pool is not in use,

rotate the Swing Ladder to the

up position and secure it in place

with the padlock as shown.

Safety Rules

■Locate ladder on a solid base.

■One person on the ladder at

a time.

■Ladder MUST be installed per

manufacturer’s instructions.

■Secure ladder to top rail of

pool for greater stability and

safety as outlined in this

assembly manual. Use of a

ladder pad is highly

recommended to protect

pool liner.

■DANGER: No Jumping or

Diving from ladder.

■Face ladder when entering

and leaving pool.

■To prevent entrapment or

drowning — DO NOT swim

through, behind or around

ladder.

■Ladder to be used as a

swimming pool ladder only.

■Weight limit -

300 lbs. maximum

■Warning: Exceeding the

maximum weight restriction

may cause the ladder to fail.

■When ladder is not in use,

swing up outside ladder

section and lock using

padlock. Ladder must be

locked at all times when not in

use or when there is no

qualied adult supervision.

■Consult your local Building

Department before installation

of your pool and equipment.

■DANGER: Use a cordless

drill for assembly and

installation. NEVER use an

electric drill in or around the

pool.

IMPORTANT For Your Safety

■Check the contents of the

carton with the parts list for

this ladder.

■DO NOT attempt to

assemble or install the ladder

if there are ANY shortages of

parts or hardware.

■For proper assembly and

installation follow all

instructions in the sequence

shown.

■Before using the product, after

assembly and installation, go

over the instructions and

procedures again to make

sure nothing has been

overlooked.

■Be sure and safe. The

manufacturer IS NOT

responsible for improper

assembly, installation

and use.

MAINTENANCE:

To keep your new ladder

working properly, just hose off

once a week with clean water.

Check the Swing-up Ladder for

proper operation. Check padlock

for proper operation, lubricate if

necessary.

WINTERIZING:

Unfasten the ladder from pool

ledge and remove from the

water. Lay the ladder on its side

to drain. It will take several

minutes for the water to drain

out of the ladder rails. A small

amount of water left in ladder will

not cause any damage. Store in

a safe place out of the elements.

OCEAN BLUE WATER

PRODUCTS WARRANTY

Ocean Blue Water Products warrants

their swimming pool ladders to be free

from defects in workmanship for one

year from date of purchase.

DO NOT RETURN

DEFECTIVE PART TO

DEALER

The defective part should be

returned, postpaid, to:

Ocean Blue Water Products

7447A S Central Ave

Bedford Park IL 60638

Enclose proof of purchase (receipts,

etc.) showing date purchased, your

name, address, and daytime phone

number. You will be notied of cost to

replace part. This warranty gives you

specic legal rights, and you may

also have other rights which may vary

from state to state.

Made in U.S.A • Printed in U.S.A.

- 7 -

Not for Use with

Soft Sided Pools

Inhaltsverzeichnis

Andere Ocean Blue Beleuchtungsausrüstung Handbücher

Ocean Blue

Ocean Blue 400950 Einrichtungshandbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung