OEM Tools 24497 Bedienungsanleitung

UNPACKING

After unpacking unit, inspect carefully for any damage

that may have occurred during transit. Check for loose,

missing, or damaged parts. If any damage is observed, a

shipping damage claim must be ﬁled with carrier. Do not

use the OEMTOOLS®Chop Saw if broken, bent, cracked or

damaged parts (including labels) are noted. Any Chop Saw

that appears damaged in any way, operates abnormally or is

missing parts should be removed from service immediately.

If you suspect that the Chop Saw was subjected to shock

load (a load that was dropped suddenly, unexpectedly, etc.)

immediately discontinue use until it has been checked by a

factory authorized service center.

Please read and save these instructions. Read through this owner’s manual carefully before using product. Protect yourself and

others by observing all safety information, warnings, and cautions. Failure to comply with instructions could result in personal

injury and/or damage to product or property. Please retain instructions for future reference.

The following safety information is provided as a guideline to help you operate your Chop Saw under the safest possible

conditions. Any tool or piece of equipment can be potentially dangerous to use when safety or safe handling instructions

are not known or not followed. The following safety instructions are to provide the user with the information necessary for

safe use and operation. Please read and retain these instructions for the continued safe use of your service system. Failure

to follow instructions listed below may result in serious injury. In addition, make certain that anyone who uses the equipment

understands and follows these safety instructions as well.

Operating Instructions and Parts Manual 24497

FOR CUSTOMER SERVICE

Technical Question?

CALL 1-866-458-2472

[email protected]

14"CHOP SAW

Thank you very much for choosing an OEMTOOLS®Product!

For future reference, please register your new tool at www.oem-tools.com and complete the owner’s record below:

Model: _______________ Purchase Date: ___________

Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this

product before you begin using it. This product is designed for certain applications only. OEMTOOLS®cannot be responsible

for issues arising from modiﬁcation. We strongly recommend this product is not modiﬁed and/or used for any application other

than that for which it was designed. If you have any questions relative to a particular application, DO NOT use the product until

you have ﬁrst contacted customer service to determine if it can or should be performed on the product.

WARNING: Pursuant to California Proposition 65, this product contains chemicals known to the state of California to cause

cancer and birth defects or other reproductive harm. Wash hands after handling.

Explanation of Safety Signal Words

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result

in property damage.

NOTES: Provide clarity and helpful information.

WARNING

1/17

2017 OEMTOOLS®

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

POWER TOOL SAFETY

WARNING

Read and understand all safety warnings and instructions.

Failure to follow the warnings and instructions may result in

electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference.

WORK AREA SAFETY

1. Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

2. Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂammable liquids, gases or

dust. Power tools create sparks which may ignite the

dust or fumes.

3. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

1. Double insulated tools are equipped with a polarized plug

(one blade is wider than the other). This plug will ﬁt in a

polarized plug only one way.

2. If the plug does not ﬁt fully into the outlet, reverse the plug.

If it still does not ﬁt, contact a qualiﬁed electrician to install

a polarized outlet. Do not alter the plug in any way. Double

insulation eliminates the need for the three-prong grounded

power cord and grounded power supply system.

3. Avoid body contact with grounded surfaces such as

pipes, radiators, ranges and refrigerators. There is

increased risk of electric shock if your body is grounded.

4. Do not expose power tools to rain or wet conditions.

Water entering the power tool will increase the risk of

electric shock.

5. Do not abuse the cord. Never use the cord to carry the

tool or pull the plug from an outlet. Keep cord away from

heat, oil, sharp edges or moving parts. Replace damaged

cords immediately. Damaged cords increase the risk of

electric shock.

6. When operating a power tool outdoors, use an outdoor

extension cord marked “W-A” or “W”. These cords are

rated for outdoor use and reduce the risk of electric

shock.

7. When not in use, disconnect from the power source and

store in a safe, dry childproof location.

8. Avoid body contact with grounded surfaces such as

pipes, radiators, ranges and refrigerators.

PERSONAL SAFETY

1. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power tool

while you are tired or under the inﬂuence of drugs, alcohol

or medication. A moment of inattention while operating

power tools may result in serious personal injury.

2. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the

off-position before connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying power

tools with your ﬁnger on the switch or energizing power

tools that have the switch on invites accidents.

4. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

5. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

6. Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

7. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust related hazards.

POWER TOOL SAFETY

1. Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

2. Do not use the power tool if the switch does not turn it on

and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

4. Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

5. Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

7. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

8. Hold the power tool by insulated gripping surfaces when

performing an operation where the cutting tool may

contact hidden wiring or its own cord. Contact with a

“live” wire will make exposed metal parts of the tool “live”

and shock the operator.

9. Use clamps or other practical ways to secure and support

the workpiece to a stable platform. Holding the workpiece

by hand or against your body leaves it unstable and may

lead to loss of control.

SERVICE

Have your power tool serviced by a qualiﬁed repair person

using only identical replacement parts. This will ensure that

the safety of the power tool is maintained.

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

SPECIFIC SAFETY RULES

WARNING

1. Know your chop saw. Carefully read and understand

this Instruction Manual. Learn the tool’s applications

and limitations, as well as the speciﬁc potential hazards

related to this tool. Following this rule will reduce the risk

of electric shock, ﬁre, or serious injury.

2. Always wear eye protection. Any power tool

can throw foreign objects into your eyes and cause

permanent eye damage. ALWAYS wear safety goggles

(not glasses) that comply with ANSI safety standard

Z87.1. Everyday glasses have only impact resistant

lenses. They ARE NOT safety glasses.

3. Glasses or goggles not in compliance with ANSI Z87.1

could cause serious injury when they break.

4. Always wear hearing protection and a dust mask. Use

only in a well-ventilated area. Using personal safety

devices and working in a safe environment reduces the

risk of injury.

WARNING

Always unplug the tool from the power source before

changing the cutting disc or when cleaning the tool.

WARNING

Never place your hands or ﬁngers near the cutting disc while

the tool is running. Severe injury will result.

WARNING

Never install a saw blade on this tool. It is designed ONLY for

use with abrasive cut off discs.

5. Use this chop saw for cutting steel only. Cutting ceramic

materials will create excessive dust and cause damage to

the motor.

6. Always use a dust mask along with safety goggles when

operating the chop saw.

7. Always use hearing protection when operating of the

chop saw.

8. Do not wear gloves, neckties or loose clothing.

9. Do not cut material too small to be securely held in the vise.

10.Always keep your hands out of the path of the cut off

disc. Avoid awkward hand positions where a sudden slip

could cause your hand to move into the path of the cut

off disc.

11.Secure the workpiece. Use the clamping system provided

with the chop saw. It is safer than using your hand.

12.Make sure there are no foreign objects in the part of the

workpiece to be cut.

13.The cut off disc must be securely attached as described

in this Owner’s Manual before connecting the tool to the

power source. Failure to do so will increase the risk of

serious injury if the cut off disc shatters or comes loose.

14.Make sure the guard is installed and in proper working

order before operating the chop saw.

15.Cut off discs must be stored in a dry location to prevent

deterioration.

16.Before attaching the cut off disc, inspect it for visible

defects. If cracked, chipped or warped, do not install it.

17.Do not over tighten the clamp nut on the cut off disc.

Excessive tightening may cause the disc to crack and

possibly shatter during operation.

18.Never turn the chop saw ON with the cut off disc

touching the work surface.

19.Use only cut off discs in compliance with ANSI Standard

B7.1 and rated for a speed greater than 3500 RPM.

20.Do not use the chop saw if the disc ﬂanges or cap screws

are missing or improperly installed.

21.Dust and abrasive materials should not be allowed to

build up in the workshop. Hot metal sparks could start a

ﬁre.

22.Do not remove the soft paper in the centre of the cut off

disc.

23.Do not alter or enlarge the center hole of the cut off disc

as this could result in the disc shattering.

WARNING

Use only cut off discs that are recommended for this chop

saw. Follow the instructions that accompany the cut off

discs. The use of improper cut off discs may result in injury

to the operator or damage to the chop saw.

WARNING

To avoid ﬁre or toxic reaction, never use gasoline, naphtha,

acetone, lacquer thinner or similar highly volatile solvents to

clean the tool.

ELECTRICAL WARNING

POWER SOURCE CONNECTION POWER

REQUIREMENTS

This product is designed to operate on a properly grounded

120 volt, 60Hz, single-phase alternating current (AC) power

source fused with a time delayed fuse or circuit breaker. It is

recommended that a qualiﬁed electrician verify the ACTUAL

VOLTAGE at the receptacle into which the product will be

plugged and conﬁrm that the receptacle is properly fused

and grounded.

DO NOT OPERATE THIS PRODUCT if the ACTUAL power

source voltage is less than 105 Volts AC or greater than

132 Volts AC. Contact a qualiﬁed electrician if this problem

exists. Improper performance and/or damage to the product

will result if operated on inadequate or excessive power.

DO NOT abuse cord. Never use the cord to carry tools or

pull the plug from an outlet. Keep cord away from heat, sharp

edges or moving parts. Replace damaged cords immediately.

Damaged cords increase the risk of electric shock.

EXTENSION CORD SAFETY

WARNING

Keep the extension cord clear of the working area.

Position the cord so it will not get caught on the

workpiece, tools or any other obstructions while you are

working with the power tool.

1. Make sure any extension cord used with this tool is in

good condition. When using an extension cord, be sure

to use one of heavy enough gauge to carry the current

the tool will draw. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating.

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

2. The table below shows the correct size to use according

to cord length and nameplate ampere rating. If in doubt,

use the next heavier gauge. The smaller the gauge

number the heavier the cord.

3. Be sure your extension cord is properly wired and in

good condition. Always replace a damaged extension

cord or have it repaired by a qualiﬁed electrician before

using it. Protect your extension cord from sharp objects,

excessive heat and damp or wet areas.

4. Use a separate electrical circuit for your power tools. This

circuit must not be less than 14 gauge wire and should be

protected with either a 15 A time delayed fuse or circuit

breaker. Before connecting the power tool to the power

source, make sure the switch is in the OFF position

and the power source is the same as indicated on the

nameplate. Running at lower voltage will damage the

motor.

MINIMUM GAUGE (AWG) EXTENSION

CORDS (120 V use only)

Amperage

rating

Total length

than

Not

than

25'

(7.5 m)

50'

(15 m)

100'

(30 m)

150'

(45 m)

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Applicable

IMPORTANT SAFETY INSTRUCTIONS

The warnings, precautions, and instructions discussed in this

manual cannot cover all possible conditions and situations

that may occur. The operator must understand that common

sense and caution are factors which cannot be built into this

product, but must be supplied by the operator.

WARNING

Use only attachments recommended or sold by

manufacturer. Verify the following every time the chop saw

is used. Failure to adhere to these safety rules can greatly

increase the chances of serious injury.

1. Do not disassemble the saw. Take it to a qualiﬁed

professional when service or repair is required. Incorrect

reassembly may result in electric shock or ﬁre.

2. Wear approved safety eye/face shield, ear defenders and

hand protection.

3. The power cord is not damaged.

4. The cut off disc is correct for the type of material being cut.

5. The cut off disc is in good condition and securely

tightened onto the arbor.

6. The guard is in good working order.

7. No ﬂammable liquids are in the vicinity.

DISPOSAL

At the end of the useful life of the OEMTOOLS®14" Chop

Saw, dispose of the components according to all state,

federal and local regulations.

PURPOSE

The OEMTOOLS®14" Chop Saw is designed to slice through

metal and other tough materials. It will cut pipe, fence posts,

tubing and other dense materials. The included vise holds

the workpiece safely and securely.

PRODUCT SPECIFICATIONS

Power: 15 Amp

No-Load Speed: 3,700 RPM

Disc Diameter: 14"

Clamping Vise: Yes

Arbor: 1"

Max. Cutting Depth: 4.72" Round Pipe

Max. Cutting Depth: 4.33" Square

Power Cord Length: 6 Ft.

Weight: 33 Lbs.

INSTRUCTIONS

Always wear safety goggles and gloves.

ASSEMBLY AND OPERATION

WARNING

Always disconnect your chop saw from the power source

when replacing the cut off disc, clamping material in the

vise, adjusting the guard, cleaning or when not in use.

Disconnecting the chop saw will prevent accidental starting

that could cause serious personal injury.

SELECT THE WORK SURFACE

It is important to place the chop saw on a solid ﬂat work

surface that will not shift during operation of the chop saw.

Locating the chop saw near an electrical outlet will eliminate

the need for an extension cord.

WARNING

Never place the chop saw near any ﬂammable liquids

or items that can be damaged by the sparks thrown by

the chop saw during cutting. The hot sparks can ignite

ﬂammable liquids.

NOTE: Hot metal sparks and sharp metal pieces will damage

the work surface to some degree. Make sure you consider

this fact when selecting the work surface. A nonﬂammable

surface such as a metal bench will be less likely to be

damaged during the cutting operation.

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

SETTING THE DEPTH STOP

NOTE: The maximum cut depth is controlled by adjusting

the depth stop.

1. Lift the swing arm upward as far as it will go. (Figure 1)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 1

2. Loosen the depth stop lock nut by turning it

counterclockwise.

3. Turn the depth stop screw to raise or lower it. Adjust until

the cut off blade enters the base slot no more than 3/16"

(5 mm) when the swing arm is fully lowered and contacts

the top of the depth stop screw.

4. When the depth stop screw is correctly set, lock it in

place by tightening the lock nut clockwise.

CHECKING THE AUTOMATIC GUARD

The automatic guard must be checked to ensure it is working

properly.

WARNING

Always disconnect your chop saw from the power source

before checking the automatic guard.

1. Lift the guard upward approximately 3" and then release

it. (Figure 2) If the guard is functioning correctly, it will

freely drop down to its original position.

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 2

2. Lower the swing arm and cutting disc assembly until

the lower edge of the guard touches the chop saw

base. Continue to lower the swing arm and cutting disc

assembly. The automatic guard should freely rise as the

cutting disc is lowered.

NOTE: The guard should always rise and fall freely when the

swing arm is lowered and raised as outlined in #1 and #2

above. If not, clean any cuttings out from around the guard

mechanism. (Figure 3)

Figure 3

CHECKING THE ARBOR CAP SCREW

It is important to check the arbor cap screw to make sure the

cut off disc is fully tightened.

WARNING

Disconnect your chop saw from the power source before

checking the arbor cap screw.

1. Lift swing arm fully upward as far as it will go.

2. Lift the disc guard fully upward until it will stay in the

upright position. (Figure 4)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 4

3. Press and hold the arbor lock to the right while rotating

the cut off disc by hand.

4. When the arbor lock engages the arbor, tighten the arbor

cap screw by turning it clockwise using the 8 mm hex key

supplied.

NOTE: Only use the hex key supplied to tighten the arbor

cap screw. Do not over tighten the arbor cap screw as you

could crack the hub of the cutting disc.

5. When the arbor cap screw is fully tightened, remove the

hex key, release the arbor lock and lower the disc guard.

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

SETTING THE MITRE VISE ANGLE

The mitre vise can be set for cutting at angles from 90° to

45° either left or right.

1. Open the vise by turning the vise adjustment crank 5 or 6

turns counterclockwise. (Figure 5)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 5

2. Loosen the mitre gauge cap screws by turning them

counterclockwise using the 8 mm hex key supplied.

(Figure 6)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 6

3. Rotate the mitre gauge to the left or right until the desired

cutting angle lines up with the alignment mark.

4. Tighten both the mitre gauge cap screws to lock the mitre

gauge in place.

NOTE: Always make a test cut on a scrap workpiece to

verify the mitre angle setting.

CUTTING UP TO 5" WIDE WORKPIECES

The vise is set up at the factory for cutting workpieces up to

5" in width. This is the preferred set-up. If it is necessary to

cut workpieces between 5" and 7" in width, the mitre gauge

will have to be relocated on the chop saw base.

1. Remove the front and rear mitre gauge cap screws using

the 8 mm hex key supplied. (Figure 7)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 7

2. Move the mitre gauge back approximately 1-1/2" until the

hole and slot in the mitre gauge line up with the next two

holes in the chop saw base.

3. Reinstall and tighten the mitre gauge cap screws in the

two new holes.

NOTE: To cut workpieces between 7" and 9" in width, locate

the mitre gauge in the back two holes in the chop saw base.

OPERATING THE VISE QUICK RELEASE

The vise has a quick release feature that allows for making

major adjustments much quicker.

1. To operate the quick release system, turn the vise crank

counterclockwise 2 or 3 turns to loosen the vise jaws.

(Figure 8)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 8

2. Lift upward on the front of the quick release nut to release

the vise screw.

3. While holding the quick release nut upward in the

released position, pull the vise crank toward you to

quickly open the vise.

4. To quickly close the vise, release the quick release nut

and push the crank away from you.

5. Use the crank to completely tighten the vise on the

workpiece.

WARNING

Always make sure the workpiece is ﬂat against the chop saw

base and securely held in the vise before turning the saw ON.

ON/OFF SWITCH

1. To turn the switch ON, squeeze the trigger switch until the

chop saw starts. During operation, you should continuing

to squeeze the trigger switch. (Figure 9)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 9

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

2. To turn the tool OFF, release the trigger switch.

WARNING

Always make sure the cut off disc is NOT touching the

workpiece when the switch is being turned ON. Let the

motor come to full speed before beginning to cut.

REPLACING THE CUT OFF DISC

The cut off disc must be replaced when it has become

damaged in any way or it has worn down to a diameter of

less the 10".

WARNING

Disconnect your chop saw from the power source before

attempting to change the cut off disc.

1. Lift the swing arm fully upward.

2. Lift the guard fully upward until it exposes the arbor cap

screw. (Figure 10)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 10

3. Press and hold the arbor lock to the right while rotating

the cut off disc by hand.

4. When the arbor lock engages the arbor, loosen the arbor

cap screw by turning it counter clockwise using the 8 mm

hex key supplied.

5. Remove the arbor cap screw, the small outer washer, the

large outer washer, the cut off disc and large inner washer

from the arbor. (Figure 11)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 11

6. Use a clean dry brush or cloth to carefully remove all

cuttings from the arbor and the motor housing.

7. Reinstall the washers, new cut off disc and arbor cap

screw in the same order in which they were removed.

NOTE: Make sure the large outer surfaces of the large and

small washers are facing the cut off disk. Make sure the

ﬂats of the washer holes slide over the matching ﬂats of

the arbor.

8. Engage the arbor lock and tighten the arbor cap screw

using the 8 mm hex key supplied.

9. Carefully rotate the cut off disk by hand to make sure it is

ﬁrmly tightened, that it is not damaged and that it does

not wobble.

WARNING

Reset the depth stop as shown in Fig. 1. The new blade will

be larger and will damage the work surface if the depth stop

is not re-adjusted.

10.With depth stop properly set and the guard in the down

position, turn the switch ON.

NOTE: If the cut off disc wobbles or vibrates, turn the switch

OFF immediately. Re-check to make sure the cut off disc is

installed correctly and that the disc is not damaged.

LOCKING THE SWING ARM FOR CARRYING

To safely carry the chop saw, it is important to lock the swing

arm and carry the tool with the appropriate carrying handle.

1. Lower the swing arm as far as it will go. (Figure 12)

Fig. 1

Fig. 2

Fig. 3

Fig. 5

Fig . 4

. 6

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. 11 Fig. 12

Figure 12

2. Push inward on the swing arm locking pin until it engages

the hole in the swing arm.

3. Release the swing arm. It will be locked in the DOWN

position if the swing arm locking pin is properly engaged.

4. Lift the chop saw using the rear handle.

CUTTING METAL

1. Lift the swing arm fully upward as far as it will go.

2. Adjust the mitre gauge as required.

3. Firmly lock the metal workpiece to be cut in the vise.

4. Make sure you are wearing your safety goggles, dust

mask and hearing protection.

5. Lower the cut off disc until it is about 1" above the

workpiece.

NOTE: The cut off disc MUST NOT be touching the

workpiece when the motor switch is turned ON.

6. While holding the chop saw handle ﬁrmly in your right

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

hand, turn the motor switch ON.

7. Wait for motor to come up to its full speed. Carefully

lower the cut off disc until it contacts the workpiece.

NOTE: Many sparks will be generated as soon as the cut off

disc touches the workpiece.

8. Apply only slight pressure to the chop saw handle as it

begins to cut through the workpiece. Do not apply too

much pressure to the handle as this will cause the motor

to slow down. Doing so will slow the cutting action and

damage the motor.

9. When the cut off disc has completely cut through the

workpiece, release the trigger switch immediately. Wait

for the motor to come to a complete stop before lifting

the cut off disc away from the workpiece.

WARNING

Never touch the workpiece immediately after a cut is

completed. The metal in the cutting area will be red hot and

will cause severe burns to your skin.

MAINTENANCE

WARNING

When servicing, use only identical replacement parts. The

use of any other part may create a hazard or cause product

damage.

DO NOT use solvents when cleaning plastic parts. Plastics

are susceptible to damage from various types of commercial

solvents and may be damaged by their use. Use a clean

cloth to remove dirt, dust, oil, grease etc.

WARNING

Do not allow brake ﬂuids, gasoline, petroleum-based

products, penetrating oils, etc. to come into contact with

plastic parts. They contain chemicals that can damage,

weaken or destroy plastic.

Keep the air vents cleared of any built up dust to prevent

the motor from overheating. Remove accumulated dust and

debris regularly using a soft DRY brush.

WARNING

Use safety goggles when using an air jet to blow dust out of

the chop saw.

DO NOT abuse power tools. Abusive practices can damage

the tool and the workpiece.

WARNING

Do not attempt to modify tools or create accessories. Any

such alteration or modiﬁcation is misuse and could result in a

hazardous condition leading to possible serious injury. It will

also void the warranty.

NOTE: It has been found that electric tools are subjected to

accelerated wear and possible premature failure when they

are used on ﬁberglass boats and sports cars, wallboard,

spackling compounds or plaster. The chips and grindings

from these materials are highly abrasive to electric tool parts

such as bearings, brushes, commutators, etc. Consequently,

it is not recommended that this tool be used for extended

work on any ﬁberglass material, wallboard, spackling

compounds or plaster. During any use on these materials it

is extremely important that the tool is cleaned frequently by

blowing it out with an air jet.

LUBRICATION

All of the bearings in this tool are lubricated with a sufﬁcient

amount of high-grade lubricant for the life of the unit under

normal conditions. Therefore, no further lubrication is

required.

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

Figure Description Qty.

Hex Bolt 1

B Small Clamp 1

C Clamp 2

D Cutting Wheel 1

E Wrench 1

F Rubber Foot 4

G Base 1

H Hex Nut 4

I Vise Stand 1

J Washer 5

K Standard Spring Washer 3

L Hex Bolt 2

M Screw Assembly 1

N Hatch Pin 2

O Small Clamping Plate 1

P Vise Column Pin 1

Q Brush Cap Holder 2

R Carbon Brush 2

S Brush Holder 2

T Rear Cover 1

U Cross Screw 2

V Cross Screw 2

W Cross Screw 1

X Standard Spring Washer 1

Y Housing 1

Z Stator 1

AA Bearing 1

BB Rotor 1

CC Standard Spring Washer 6

DD Cross Screw 2

EE Switch 1

FF Trigger 1

GG Cross Screw 2

HH Handle 1

II Cross Screw 2

JJ Cross Screw 1

KK Cross Screw 2

LL Left Handle 1

MM Cross Screw 2

NN Cord 1

OO Cord Armor 1

PP Cable Wire 1

QQ Right Handle 1

RR Hex Nut 3

SS Handle 1

Figure Description Qty.

Cross Screw 6

UU Anti-Wind Ring 1

VV Bearing 1

WW Gear Box 1

XX Protective Cover 1

YY Cross Screw 4

ZZ Active Cover 1

AAA Screw 2

BBB Spindle 1

CCC Semi-Circle Key 1

DDD Bearing 1

EEE Spring Lock Pin 1

FFF Lock Pin 1

GGG Bearing Holder 1

HHH Gear 1

III Spring Washer 1

JJJ Bearing 1

KKK Circumgyrate Pin 1

LLL Cross Screw 1

MMM Washer 1

NNN Standard Spring Washer 1

OOO Dust Board 1

PPP Big Spring 1

QQQ Hex Nut 1

RRR Hex Bolt 1

SSS Pipe 1

TTT Height Limited Pin 1

UUU O-Ring 1

VVV Limited Pin Cap 1

WWW Hex Nut 1

XXX Hex Screw 1

YYY Hex Bolt 2

ZZZ Standard Spring Washer 2

AAAA Washer 2

BBBB Scale Plate 1

CCCC Column Spring Pin 1

DDDD Speed Nut 1

EEEE Fastener 3

FFFF Hex Nut 2

GGGG Cross Screw 3

HHHH Cover Protector 1

IIII Cross Screw 2

JJJJ Column Cover Pin 1

KKKK Washer 2

LLLL Cross Screw 2

Parts List

This symbol designates that this tool is

listed with U.S. requirements by ETL Testing

Laboratories, Inc. Conforms to UL STD No.987

Certiﬁed to CAN/CSA STD C22.2 No. 71.2.

Intertek

3151837

HZ932C

C US

Operating Instructions and Parts Manual 24497

14"CHOP SAW

1/17

2017 OEMTOOLS®

CCCC

DDDD

YYY

ZZZ

AAAA

UUU TTT

SSS RRR

QQQ DD

LLLL

PPP

OOO

NNN

MMM

LLL KKK JJJ III HHH

GGG

FFF

EEE

DDD

CCC BBB

FFFFF

EEEE

AAA

GGGG

HHHH

IIII

JJJJ

KKKK

VWX

HH II

JJ KK LL

MM NN OO PP

XXX

WWW

VVV J

BBBB

Parts Diagram

NOTE:

Not all components of the Chop Saw are replacement items, but are

illustrated as a convenient reference for location and position in the

assembly sequence.

Inhaltsverzeichnis

Andere OEM Tools Gesehen Handbücher

OEM Tools

OEM Tools 24488 Service-Handbuch

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung