Ofna Racing DM-ONE-SPEC e Bedienungsanleitung

1.Before Starting

2.While Operating

•If you are under 18 please read manual (with a parent, guardian or a responsible adult if necessary).

•Any running area you choose must be dry. Do not run car near any water or wet dirt.

•Do not run on public streets. It is very easy to have the car run over or be damaged by hitting the curb.

•Do not operate the car in tight confined space. The car is very fast and will easily hit something.

•Do not run near people or animals. The car is very fast and could easily hit someone if you are not an

expert driver.

•Do not operate the car at night. You will not be able to drive it safely.

3.Before Operating

•Make sure that all screws and nuts are properly tightened.

•Radio-Check battery life before running the car. If the radio does not have full control of the car with

steering and/or throttle/brake, do not run until corrected. Failure to correct this will result in possible

injury and damage to the car or property.

•Please confirm the neutral throttle trigger position.

4.Check Your Car After Running

•Turn OFF receiver first, then turn OFF transmitter. This will prevent the car from losing control.

•After running radio controlled car , it is necessary to perform routine maintenance.

5.Battery Safety

IMPORTANT-READ THIS BEFORE RUNNING

•Please be careful when handling the battery. It will be hot after running. If the wire is frayed, a short

circuit can cause a fire.

TOOLS NOT INCLUDED IN THE KIT

Cutter

Curved Scissors

Craft Knife Precision Caliper

Needle Nosed Pliers

Equipment Needed

OVERVIEW

Components

Transmitter

Parts Bag

Receiver

Radio Control Car

UM-3 Batteries

( 8pcs )

Body Reamer

Instant Cemment

Screw Cement

GEAR

GREASE

Gear Grease

7.4V L

i-Po Battery(Hard Case)

L Battery Chargeri-Po

Servo

Brushless Motor

Brushless Electric

Speed Controller

40533

FRONT AND REAR GEAR BOX

40538

DIFF. CASE

40040

CENTER DIFF. MOUNT PLASTIC PARTS

40721

FRONT BUMPER

31304

REAR UPRIGHT

40643

SHOCK PLASTIC

Parts for

Not Use

PLASTIC PARTS FOR USE

4071940719

ARM HOLDER

40537

REAR UPPER ARM

30663

VELCRO BATTERY STRAPS

40720

SIDE IMPACT BUMPER AND BODY POST

40539

SERVO SAVER

SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL

Ensure

Free

Movement

Ensure Free

Movement

Apply

Grease

Apply Grease

Oil

Tighten

Do Not

Over Tighten

Rotate

Direction Rotate

Direction

Contact

Adhesive

Contact Adhesive

Screw

Cement

BAG

1:1

Parts Bag Used Degrease With

Motor Spray

Do Not

Over Tighten

Clockwise

Rotation

Anti-clockwise

Rotation

True-To-Scale

Apply OilApply Screw

Cement

40717

FRONT AND REAR LOWER ARM

40718

FRONT KNUCKLE ARM

40716

FRONT UPPER ARM

PLASTIC PARTS FOR USE

30662

BATTERY CASE

ASSEMBLY OF THE FRONT SHOCKS

2ASSEMBLY OF THE REAR SHOCKS

•Assemble 2 seets for front Step 1 Step 2 Step 3 Step 4

1.Pull down piston and pour

oil into shock cylinder.

2.To remove air bubbles by

slowly moving piston up

and down.

3.Pull down piston, attach

pressure top and shock oil

overflow with tissue paper.

020 30 4010

Fill the shocks with oil #80wt.

Step 5 Step 6

•Fit the o-ring into groove

before assembly.

40633

40640

40636

Oil

40090

2mm

40090

1mm

40634

40737

40736

2.6x5mm

40060

40638

2.6x5mm

30403

40643(Short)

CORRECT SHOCK ASSEMBLY

Carefully screw the shock

shaft into the bottom of the

plastic ball and until the

distance between the ball

end and the shock is 14mm.

Do not over tighten

as the plastic will strip.

Oil

•Be careful not to damage shock shaft.

Tighten

40643

40640

020 30 4010

40633

40640

40090

2mm

40090

1mm

40634

40632

Step 3

2.6x5mm

40638

2.6x5mm

30403

40643(Short)

40054

40643

40090

2mm Washer

40090

1mm Washer

40090

3.5mm O-Ring

40090

7mm R-Ring

Step 6

40060

40751

.....x4

.....x2

Step 2

*Assemble 2 seets for rear Step 1

40090

2mm Washer

40090

1mm Washer

40090

3.5mm O-Ring

40090

7mm R-Ring

.....x4

.....x2

Oil

14mm

1.Pull down piston and pour

oil into shock cylinder.

2.To remove air bubbles by

slowly moving piston up

and down.

3.Pull down piston, attach

pressure top and shock oil

overflow with tissue paper.

Oil

•Fit the o-ring into groove

before assembly.

40636

Step 4

Fill the shocks with oil

#60wt.

•Be careful not to damage shock shaft.

Step 5

Tighten

CORRECT SHOCK ASSEMBLY

Carefully screw the shock

shaft into the bottom of the

plastic ball and until the

distance between the ball

end and the shock is 32mm

Do not over tighten

as the plastic will strip.

32mm

Step 1 Step 2

ASSEMBLY OF THE FRONT AND REAR DIFF.

36053

40514

4x4mm

40538

40009

40513

40517(43T)

40009

40513

36053

8x16mm

Ball Bearing

94034

4x4mm

Set Screw

40010

2.5x13.8mm Pin .....x4

.....x4

.....x2

40009

P6 O-Ring

40514

36053

40010

.....x16

30776

4x10mm

Washer

30773

4mm

Cross Pin .....x4

ASSEMBLY OF THE FRONT AND REAR DIFF.

Diff. Oil

40011

3x12mm

30773

40024

13x16x0.2mm

Shim .....x8

36053

8x16mm Ball Bearing

.....x4

5ASSEMBLY OF THE FRONT AND REAR GEAR CASE

5x4mm

40519

40533

40024

36053

4x35mm

40024

40516(13T)

36053 4x15mm

40533

40010

•Put the Diff. Oil #100000 for front

and the #5000 for Rear

•Fill the Diff. case to approx. 80%

with the Diff. Oil

40513

30776

Step 1 Step 2

94020

3x12mm

Flat Head

Hex Screw

.....x8

94015

4x35mm

Hex Screw

.....x4

94011

4x15mm

Hex Screw

.....x4

Tight the diff screws in this order.

Srw

Ce n

me t

Oil

Tighten

Apply

Grease

Builds two differentials for front and rear.

Builds two gear case for front and rear.

•Adjust the backlash with the shims.

3x12mm

ASSEMBLY OF THE SERVO SAVER

40719

ASSEMBLY OF THE SERVO SAVER

.....x5

94041

3mm

Nylon Nut

40539

6x10mm

Plastic Bearing .....x4 40511

3x10mm

40745

40539

ASSEMBLY OF THE SERVO SAVER

40563

40539

40034

40500(Black)

40539

4x8mm

Plastic Flange

Bushing

40037

Steering Plat

Hex Screw .....x2

.....x2

40024

13x16x0.2mm

Shim .....x2

40539

40024

40037

40746

40539

• Notice the direction of the servo saver connecting plate.

40719

.....x2

40531

Shock Ball

End Post

40531

3x25mm

40719

4x12mm

.....x5

Step 1 Step 2

3mm

94003

3x10mm

Hex Screw

90018

3x25mm

Cap Screw

94026

4x12mm

Flat Head

Hex Screw

.....x2

•Tighten the steering plate hex screw

all way down and then back it off 1/2

turn.

Ensure

Free

Movement

*Set the left and right hand side upper arm

adjuster in the same direction.

Left Right

Oil

Rotate

Direction

Srw

emnC e t

Sc er w

Cem nt

reSc w

Cmnte e

ScrewC en

em t

40539

3mm

40539

ASSEMBLY OF THE STEERING TIE-ROD

Step 1

Approx. 29.30 mm

1:1

Front

40533

Front Plate Bed

.....x4

40038

7mm Ball

.....x2

36700

40038

3x15mm

4x10mm

40548

36790

.....x2

40548

3mm

Nylon Nut

(Thin Type)

.....x2

40126

3x6mm

Flange Washer

40126

ASSEMBLY OF THE SERVO SAVER AND FRONT UPPER ARMS

.....x2

40525

3x48.1mm

Arm Shaft

40719

3x12mm

4x12mm

40716

(1mm and 3mm)

40716

(2mm)

40719

Step 2

40525

94020

3x12mm

Flat Head

Hex Screw

.....x2

94026

4x12mm

Flat Head

Hex Screw

.....x4

94009

4x10mm

Hex Screw

.....x2

*Insert the upper arm adjust

into shock stay.

40716

Step 1

Assemble both right and left side.

Step 2

•Set the left and right hand side upper arms

adjuster in the same direction.

Left Right

reSc w

Cement

94021

3x15mm

Flat Head

Hex Screw

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ofna Racing Motorisiertes Spielzeugauto Handbücher

Ofna Racing

Ofna Racing Hyper H4 Bedienungsanleitung

Ofna Racing

Ofna Racing DM-ONE PRO TOURING RTR X-SIZE NITRO SEDAN Bedienungsanleitung

Ofna Racing

Ofna Racing CD-3 SPORT RTR Bedienungsanleitung

Ofna Racing

Ofna Racing Ultra LX Comp Bedienungsanleitung

Ofna Racing

Ofna Racing Nitro Z10 Bedienungsanleitung

Ofna Racing

Ofna Racing Ultra II Bedienungsanleitung

Ofna Racing

Ofna Racing ULTRA GTP II 34316 Bedienungsanleitung

Ofna Racing

Ofna Racing Nexx 10SC Bedienungsanleitung

Ofna Racing

Ofna Racing ULTRA GT LX Bedienungsanleitung

Ofna Racing

Ofna Racing PirateMT Sport Bedienungsanleitung

Ofna Racing

Ofna Racing Hyper7 Bedienungsanleitung

Ofna Racing

Ofna Racing Hyper H4 Bedienungsanleitung

Ofna Racing

Ofna Racing HYPER10-TT Bedienungsanleitung

Ofna Racing

Ofna Racing X2 TRUGGY Bedienungsanleitung

Ofna Racing

Ofna Racing JAMMIN X1-CRT Bedienungsanleitung

Ofna Racing

Ofna Racing NEXX 8 T Bedienungsanleitung

Ofna Racing

Ofna Racing 1/8 SCALE OFF-ROAD BUGGY Bedienungsanleitung

Ofna Racing

Ofna Racing BLAZER SST Bedienungsanleitung

Ofna Racing

Ofna Racing Hyper GPX4 Bedienungsanleitung

Ofna Racing

Ofna Racing CD-3 SPORT RTR Bedienungsanleitung

Ofna Racing

Ofna Racing RAVANGER 4.6 Merkblatt

Ofna Racing

Ofna Racing HYPER SSE Bedienungsanleitung

Ofna Racing

Ofna Racing 9.5 RTR Bedienungsanleitung

Ofna Racing

Ofna Racing Ultra GTP Bedienungsanleitung

Beliebte Motorisiertes Spielzeugauto Handbücher anderer Marken

Eduard

Eduard Humber Scout Car Mk.I exterior Bedienungsanleitung

Traxxas

Traxxas 4995X Bedienungsanleitung

Jamara

Jamara VW T1 Bus Bedienungsanleitung

REVELL

REVELL 68 CHEVY CHEVELLE SS 396 Bedienungsanleitung

Schumacher

Schumacher Pro Cat Bedienungsanleitung

Tamiya

Tamiya TT-01 TYPE E Bedienungsanleitung

Eduard

Eduard Krupp Protze 6x4 1/48 Bedienungsanleitung

New Bright

New Bright 61072UEP Bedienungsanleitung

Team Durango

Team Durango DEX410v5 Bedienungsanleitung

Jamara

Jamara Mercedes Actros Muldenkipper 2,4 GHz Bedienungsanleitung

PLAYMOBIL

PLAYMOBIL 9536 Bedienungsanleitung

Atomic

Atomic BZ3 Bedienungsanleitung

Aiyaplay

Aiyaplay 370-290V00 Bedienungsanleitung

Power Wheels

Power Wheels GRJ53 Bedienungsanleitung

ZEROTRIBE

ZEROTRIBE Zetricks ZT1144 Bedienungsanleitung

INJUSA

INJUSA 412 Bedienungsanleitung

Maverick

Maverick MSC-30BR-WP Bedienungsanleitung

Land of B.

Land of B. Rollin' Riders Bedienungsanleitung