Oki C712 Benutzerhandbuch

Version 1.0

1

Thank you for choosing OKI.

This is C712 configuration instructions for Ballot model. These instructions explain 2 ways for

configuration. Manually and using Ballot Configuration Tool.

Before ballot configuration, please perform the following steps.

1. Install Extended 2nd Paper Tray for 19" Ballots (Order/Part Number 44274505).

2. Turn ON the device.

3. Print the Configuration pages. (Print Information -> Configuration -> Execute)

4. Check Serial Number and the current tray 2 setting from the configuration pages.

[Serial Number]

[Tray 2 Setting (Paper Size)] (Before Ballot Configuration)

Notes: Be sure to note down the serial number as it is necessary for inquiry.

If you do not have Ballot Configuration Tool you can set by using device menu, please

proceed to next page. In case you have Ballot Configuration Tool, please proceed to page 3.

Version 1.0

2

1. Installation Steps: Using Device panel menu (Manually)

Menus -> Tray Configuration -> Tray 2 Config

-> ->

1. Set Paper Size from “Cassette Size”

to “Custom”.

2. Return to “Tray 2 Config” Menu.

3. Set X Dimension to “8.5 inch”.

4. Set Y Dimension to “19.0 inch”.

5. Complete

Version 1.0

3

2. Installation Steps: Using Ballot Configuration Tool

①Connect the PC and the device with a USB cable.

②Copy the module of the Data Transmitter which provided by OKI to your desktop.

1. Run the Data Transmitter Tool “DT.exe”.

2. Select your language and click “OK”.

3. Select “Open” from the file menu.

4. Select “setup.dtd” file.

(To be Continued)

Version 1.0

4

5. Select “C712-b Configuration” function.

6. Search a USB connected printer. If the

device was found, select it, and click

“Send”.

7. Click “OK”.

Please wait for about 10 seconds.

After the applying configuration, the

device will restart (Turn OFF and ON)

automatically.

8. The configuration is completed. The

device will auto reboot (Turn OFF and

ON).

(To be Continued)

Version 1.0

5

9. After reboot, the device does initialize.

After initializing, the device status

changes to ready.

10. Click “OK” and close this tool.

11. Print the Configuration pages.

MENU -> Print Information ->

Configuration -> Execute

12. Check the current tray 2 setting from

the configuration pages.

Paper Size is “Custom”.

X Dimension is “8.5 inch”.

Y Dimension is “19.0 inch”.

13. Complete

Version 1.0

6

3. Confirmation of setup

You can check the setup result from the 1st page of Configuration pages.

How to print the Configuration pages. (Print Information -> Configuration -> Execute)

Where and what should you look up?

Setup was successful if the following were applied to the Tray 2 settings:

•Paper Size is “Custom”.

•X Dimension is “8.5 inch”.

•Y Dimension is “19.0 inch”.

If the above settings are not applied, please repeat above procedure.

End of File

Dieses Handbuch passt für folgende Modelle

2

Inhaltsverzeichnis

Andere Oki Drucker Handbücher

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung