Helpdesk - Feel free to call us on +27 21 009 0911 or email support@olarm.co www.Olarm.co
This section will guide you through entering a
series of codes / settings to allow the Alarm Panel
and Olarm PRO to communicate.
The IDS X-Series alarm system caters for a range
of keypads and they all work slightly dierent.
Please follow the instructions relating to your
keypad.
Configure the alarm panel
1. Ensure that the alarm system is powered up
and on.
2. Ensure the alarm is disarmed.
3. Press # to clear the keypad.
4. Enter the installer menu by typing the installer
code followed by a *.
a. The default installer code is 9999 or 999999.
b. If these do not work, please contact the
alarm installer who installed / manages
the alarm system.
5. From the installer menu, enter the code 196
followed by *.
Revision: 2.2
Troubleshooting
If your device LED remains flashing Green
for more than 3 minutes - Please check the
connection between the Olarm PRO and the
alarm panel.
If your device LED is Red - Please check the
connection between the Olarm PRO and the
alarm panel.
If your device LED is Orange - Please ensure
that the Olarm PRO is located in an area with
good Vodacom and/or MTN signal strength.
If it is not, please ensure that your device is
connected to Wifi using the wizard inside the
Olarm app.
If your device LED is not coming on - Please
check the connection between the Olarm PRO
and the alarm panel and that the alarm panel is
connected to power.
If your device LED remains purple for more
than 15 minutes - Please contact Olarm Support.
We suggest mounting the Olarm PRO device
on a wall or on the outside of the alarm panel.
Please do NOT mount the Olarm PRO inside the
alarm box or near any other radio equiprment
as it will reduce the signal strength and result in
your device not functioning correctly.
Mount the Olarm PRO
Mount your device using the screws and drill
template provided.
STEP 11
STEP 10
-’! abc def
ghi jkl mn
opq rst uvw
xyz
quick away
quick stay stay & go stay
switch
bypass
chime
partition
memory
buzz
trouble
panic
1 2 3
4 5 6
7 8
0
<< >>
#
*
9
P1 Ready 08:41
9. The Olarm PRO should turn a solid blue colour
within 2 minutes.
6. Enter the serial security code 123456
followed by *.
7. Press # button 2 to 3 times until you hear 4 to 5
beeps from the keypad, this will take you out of
the installer menu.
8. The keypad will then display:
ARMED
READY
AWAY
POWER
1 2 3
4 5 6
7 8 9
0
F M P
#
Quick away Chime Stay
Stay & goQuick stay
Troubleview
Bypass Alarmmemory
Buzz
M
O
D
E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
X-SERIES
INSTALLER MENU
Location: 196
Serial Code
User Code: 123456
Updating Panel
Please Wait...
User Menu
Master Code + *
Master Code + *
FW 2.41
To check your alarm panel firmware version
Hold down the * key on the keypad down for 3
seconds. You should see the following display.
Do NOT enter the Master Code at this stage,
instead press * which will then display the firmware
version.
TIP
Pwr
Arm
P
anic
F
ire
>>
8
rst
0
xyz
Alarm memory
5
jkl
Quick stay
2
abc
Chime
edical
M
<<
M
ode
3
def
Stay
6
mn
Stay & go
9
#
uvw
Bypass
*
Program
1
_’|
Quick away
4
ghi
Buzz
7
opq
Trouble view
P1 Ready to Arm
