Olivetti d-COLOR MF554 Bedienungsanleitung
E-1
<Important>
Be sure to correctly follow the procedures in order as explained in this Installation Manual.
If you do not follow the procedure in order, the image trouble may occur.
1. Outline of installation procedures
When installing the main body and associated options as a system, follow the order shown on the upper.
Caution:
• Lifting the main body in an awkward position or transporting it in a poorly balanced position could result in
personal injury. When transporting the main body, assign an adequate number of persons to the job and
ensure that each person can take a good position of not being excessively loaded.
(mass: approx. 110 kg (242-1/2 lb))
Note:
• For the detailed installation procedures for each option, follow the instructions given in the corresponding
installation manual and perform the procedures correctly.
• When placing the main body on the floor, make sure to use the paper feed cabinet or the desk to secure
the performance and the quality of the product.
• Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed.
Machine
Electronic system options
AU-102
AU-201S
PC-215 PC-415 DK-510 DK-705PC-115
FK-514
FK-515*
2
UK-212*
1
SC-508*
1
KP-101
WT-506
MK-735
HD-524*
1
HT-509
TK-101
KH-102 EK-608*
1
EK-609*
1
MK-730
MK-742*
2
MK-734
CU-102
LU-302
LU-207
VI-510IC-416
SP-501
UK-501
OT-506 RU-513
PK-520
FS-537FS-536 FS-537SDFS-536SD
JS-602PI-507
PK-523
ZU-609
PK-519*
3
FS-533*
3
JS-506*
3
Electronic system options
*1: No particular order in
installation procedures.
*2: Varies depending on the
applicable marketing area
*
3: MF554/MF454 only
d-Color MF654/MF554/MF454
INSTALLATION MANUAL
©Olivetti S.p.A Applied Machines: d-Color MF654/MF554/MF454
Y118120-9 Installation Manual
E-2
2. Installation space (unit: mm (inch))
d-Color MF654 + PC-215 + FS-537SD + LU-207
3. Pre-installation check items
(1) Select a level and stable place for installing the
machine.
(2) Be sure to use a power source of the voltage and
frequency indicated in the product specifications.
Ensure that the current carrying capacity of the
power outlet is at least equal to the current listed
in the product specifications.
(3) Power the machine directly from a dedicated
power outlet. (Do not use an extension cord.)
(4) Do not plug or unplug the power cord with wet or
dirty hands, otherwise you may get an electric
shock.
(5) Avoid a hot and humid environment, or a place
exposed to direct sunlight.
(6) Avoid a dusty location, or a place near volatile
and flammable substances.
(7) Avoid a poorly ventilated place.
4. Notes on using touch panel
Be sure to instruct users on the following points.
• This machine uses a capacitive touch panel.
When you touch the touch panel, use your fin-
ger or the stylus pen supplied with the machine.
If you touch the panel using your nail or a pen
tip instead of using your finger or the stylus pen,
the touch panel does not respond normally.
• Pressing the touch panel hard may cause dam-
age.
• Do not strongly press the panel or press it using
the sharp tip of mechanical pencils.
• The key is a finger tapping (quick light touch
using a finger) operation.
5. Accessory parts
* Varies depending on the applicable marketing
area.
1244
(49)
452
(17-13/16)
2477
(97-1/2)
781
(30-3/4)
1267
(49-7/8)
1560.5
(61-7/16)
353.5
(13-15/16)
953
(37-1/2)
254
(10)
847
(33-3/8)
420
(16-9/16)
No. Name Q’ty
1. User’s guide holder 1
2. Quick start guide 1
3. Installation manual 1 set
4. User’s guide CD 1
5. CD-ROM 1 set
6. Paper size label 1
7. Panel sheet 1
8. Chart 1
9. Cap A (Black) 2
10. Cap B (White) 2
11. Connector cover 1
12. Duct cover 1
13. Cord clamp A *
1
14. Cord clamp B
1
15. Screw A
(3 x 8 mm) 1
16. Screw B
(3 x 8 mm) 2
17. Screw C
(3 x 30 mm) * 1
18. Stylus pen 1
19. Waste toner box 1
Installation Manual Y118120-9
E-3
Note:
• Keep the paper size label at hand. It is neces-
sary for mounting the Large Capacity Unit LU-
302.
• Keep the cord clamp B at hand. It is necessary
for mounting the Upgrade Kit UK-212, Authenti-
cation Unit AU-201S, or Authentication Unit
AU-102.
*Power supply:
d-Color MF654: 120V 16A, 220-240V 10A d-
Color MF554/MF454: 120V 12A, 220-240V 9A
Note:
This manual provides the illustrations of the acces-
sory parts and machine that may be slightly differ-
ent in shape from yours. In that case, instead of
the illustrations, use the appearance of your
machine to follow the installation procedure. This
does not cause any significant change or problem
with the procedure.
6. Installing the main body and the Paper
Feed Cabinet (or the Desk)
(1) Take the main body and the Paper Feed Cabinet
(or the Desk) out from its packaging.
Caution:
Main body mass: approx. 110 kg/242-1/2 lb
• Make available collective manpower of an
appropriate size for transporting the main body.
Note:
• Remove the machine, holding it by the handles
on the right and left sides as shown in the illus-
tration and keeping it level.
(2) Refer to the installation manual for the Paper
Feed Cabinet (or the Desk) and follow the
“Installation Procedures.”
Note:
If installing either the Heater HT-509, the Trans-
former kit TK-101, or the Power Supply BOX MK-
734, install them at the same time as the installa-
tion of the Paper Feed Cabinet (or the Desk).
Keep this bag away from babies and
children. Do not use in cribs, beds,
carriages, or playpens.
The thin film may cling to nose and
mouth and prevent breathing. This bag is
not a toy.
If a power cord is not supplied, use only
the power cord that meets the following
conditions.
Failure to do this could result in a fire or
electrical shock.
• The power cord has voltage and current rating
appropriate for the rating plate on this machine.
• The power cord meets regulatory requirements
for the area.
• The power cord is provided with grounding
pin/terminal.
When holding the transportation handles,
be careful not to catch your fingers in the
machine.
Y118120-9 Installation Manual
E-4
7. Removing protective tape, packing and
other shipping materials
(1) Remove the protective tape and the protective
materials.
Note:
Be sure to lock the lever after removing the protec-
tive tape A.
(2) Open the right door and remove the protective
sheet and locking materials.
Note:
• After removing the locking materials, make sure
that the transfer roller assy is secured in place.
In the case of <NG>, press the transfer roller
assy into place so that it is secured as shown in
<OK>.
• Save the packaging materials removed in this
and subsequent steps of (6), (8), and (14) for
later use when transporting the machine.
(3) Close the right door.
(4) Slide out the tray 1.
(5) Remove the protective tapes from the inside of
the tray 1 and remove accessory parts.
Note:
See the User's Guide CD for instructions on set-
ting paper in each tray and configuring the paper
types.
A
< OK > < NG >
Installation Manual Y118120-9
E-5
(6) Slide out the tray 2 and remove the tray locking
materials.
(7) Remove the protective tapes from the inside of
the tray 2 and remove accessory parts.
(8) Remove the locking screws.
(9) Attach the supplied caps A and B.
(10) Remove the protective sheets.
(11) Open the lower front door.
(12) Remove the protective tape.
Protective tape
Y118120-9 Installation Manual
E-6
(13) Remove the protective tape from the develop-
ing units.
Note:
Do not remove the tape A in this procedure.
(14) Remove the locking materials from the four
places.
(15) Release the lever of the drum unit (K).
(16) Slightly slide the drum unit (K) out and remove
the protective tape.
(17) Slide the drum unit (K) into the machine.
(18) Lock the drum unit (K) with the lever.
(19) Install the supplied waste toner box.
Note:
Push the areas indicated by the “ ” marks to set
the waste toner box to the machine.
(20) Close the lower front door.
A
Installation Manual Y118120-9
E-7
8. Installing the toner cartridge
Note:
Since cartridge is not supplied with the machine,
purchase toner cartridge (of different colors) sepa-
rately.
(1) Shake the toner cartridge up and down and left
to right 5 to 10 times respectively.
Note:
Shake the cartridge adequately. Otherwise, it may
cause trouble.
(2) Open the upper front door.
(3) Insert the toner cartridge into the machine.
Note:
• Make sure that the color is same between
inserting port and the toner cartridge.
• Make sure that the blue label position of the
toner cartridge is matched with the one of the
machine side.
(4) Push the toner cartridge all the way in and rotate
it clockwise to lock it.
Note:
Make sure that the toner cartridge is pushed all the
way in.
(5) Using the same procedure, install the toner car-
tridges for other colors of toner.
(6) Close the upper front door.
9. Installing other options
To install other options, refer to the installation man-
ual for each option and follow the “Installation Proce-
dures.”
10. Mounting the accessory parts
(1) Remove the protective cover from the supplied
stylus pen.
Note:
Discard the removed protective cover.
Y118120-9 Installation Manual
E-8
(2) Set the stylus pen in the place shown in the illus-
tration.
(3) Attach the supplied connector cover to the
machine. (One supplied screw A)
(4) Attach the supplied duct cover.
(Two supplied screws B)
11. Connecting the power cord
Note:
Steps (1) and (2) may be unnecessary depending
on the applicable marketing area.
(1) Connect the power cord.
(2) Fit the supplied cord clamp A over the power
cord. (One supplied screw C)
(3) Plug the power cord into the power outlet.
Tab
Use the appropriate power cord.
Failure to do this could result in a fire or
electrical shock.
Installation Manual Y118120-9
E-9
12. Starting the machine
Open the lower front door and turn ON the power
switch, then close the lower front door.
13. Date & Time Setting/Time Zone Setting
(Service Mode)
(1) Display the Service Mode screen.
(For details of how to display the Service Mode
screen, see the service manual.)
(2) Display the Date & Time Setting/Time Zone Set-
ting screen.
(To display the Date & Time Setting/Time Zone
Setting screen, press Stop → 3 on the control
panel.)
(3) Do not input date and time but touch “Entry” of
the Date & Time Setting.
(4) Input the time zone using up/down keys or direct
keys.
(5) Touch “Entry” of the Time Zone Setting.
(6) Touch “Apply.”
(7) Touch “OK.”
(8) Touch “Next.”
14. Serial number input
Note:
Serial number input is, if necessary, needed only
for the optional devices installed in “9. Installing
other options.”
(1) Touch the item you want to enter and input the
serial number.
(2) Touch “END.”
(3) For other devices, enter their serial number in
the same way.
(4) Touch “END.”
(5) Touch “Next.”
15. Unit change
Note:
This function allows the user to select the type of
message that will appear when the replacement
time arrives for each of the different units.
(1) Select the appropriate message type for each
unit.
(2) Touch “Service.”
16. Performing Non-Image Area Erase
Check
Note:
Perform the below at the site where customer
uses the machine.
(1) Select the Non-Image Area Erase Check func-
tion as follows:
Machine → Non-Image Area Erase Check.
(2) Open fully the dual scan document feeder, the
reverse automatic document feeder, or the origi-
nal cover if loaded.
Note:
• Do NOT place a document on the document
glass.
• Clean the document glass if dirty.
(3) Press the Start key.
(4) Make sure that “Result” is “OK.”
Note:
If “Result” is “NG1” or “NG2”, review the place and
direction of installation, or take measures to block
the light source (by covering it, etc.), then perform
installation checking again.
(If a fluorescent light or other bright light sources
exist right above the machine, the light source can
hinder installation checking and cause operation
errors in the Non-Image Area Erase Check. For
detailed information, see the service manual.)
(5) Touch “OK.”
Y118120-9 Installation Manual
E-10
17. Configuring other options
(1) If any of the following options are installed, refer
to the “Configuration procedures” of the installa-
tion manual for each option and configure the
option(s).
• Paper Feed Cabinet PC-415
• Large Capacity Unit LU-207/LU-302
• Stamp Unit SP-501
• Double feed detection Kit UK-501
• Punch Kit PK-523/PK-520/PK-519
• Z Folding Unit ZU-609
• Fax Kit FK-515/FK-514
• Local Interface Kit EK-609
• Security Kit SC-508
• Authentication Unit AU-201S/AU-102
• Upgrade Kit UK-212
• Hard Disk HD-524
• Clean Unit CU-102
•Network Fax
(2) Exit from the Service Mode and return to the ini-
tial screen.
18. Connecting the network cable
(1) Connect the main body and networking equip-
ment (HUB) using the network cable.
Note:
The following shows the recommended network
cables that correspond to each communication
speed.
• 10BaseT/100BaseTX: Category 5
• 1000BaseT: Category 5E, Category 6
(2) Check LEDs for lighting conditions.
LED1:
Should light up steadily if the link network con-
nection has been made.
LED2:
Should blink according to the communications
status of the ACT network.
(3) Route the network cable.
<When adding no paper feed options/desk or when
using the Desk DK-705>
a) Route the network cable through the harness
guide and pass it through the notch.
Note:
Leave an appropriate amount of slack in the por-
tion of the cable between the plug and the harness
guide in a manner which does not interfere with
the opening and closing of the cover.
<When using the Paper Feed Cabinet PC-415/PC-
215/PC-115 or the Desk DK-510>
a) Remove the rear right cover from the paper
feed cabinet or the desk. (Two screws)
b) Remove the knockout from the rear right cover
using nippers.
Networkport
LED2
LED1
Leave an appropriate amount of slack.
Installation Manual Y118120-9
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Olivetti Multifunktionsdrucker Handbücher
Olivetti
Olivetti d-COLOR MF654 Bedienungsanleitung
Olivetti
Olivetti d-COLOR MF652 Bedienungsanleitung
Olivetti
Olivetti d-color MF551 Bedienungsanleitung
Olivetti
Olivetti d-COLOR MF652 Bedienungsanleitung
Olivetti
Olivetti d-COLOR MF652 Bedienungsanleitung
Olivetti
Olivetti d-COLOR MF652 Bedienungsanleitung
Olivetti
Olivetti d-Copia 20W Einrichtungshandbuch
Olivetti
Olivetti d-COPIA 3500MF Bedienungsanleitung
Olivetti
Olivetti d-Copia 16MF Bedienungsanleitung
Olivetti
Olivetti d-Color MF2501 Bedienungsanleitung
Olivetti
Olivetti d-Copia 283MF Bedienungsanleitung
Olivetti
Olivetti d-COPIA 3013MFplus Bedienungsanleitung
Olivetti
Olivetti d-COPIA3500MF plus Bedienungsanleitung
Olivetti
Olivetti d-Copia 2001 Bedienungsanleitung
Olivetti
Olivetti d-COLOR MF3300 Bedienungsanleitung
Olivetti
Olivetti d-Copia 2500 Bedienungsanleitung
Olivetti
Olivetti d-COPIA 255MF Bedienungsanleitung
Olivetti
Olivetti OFX9700 Bedienungsanleitung
Olivetti
Olivetti d-color MF451 Bedienungsanleitung
Olivetti
Olivetti d-color MF551 Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
