Omega LINKR-M1 Bedienungsanleitung

Installation And Testing Guide

(ENGLISH / INGLÉS)

Download the Linkr app to your smartphone.

Search ‘omega linkr’ in your app store - iphone &

android only.

Mount the Linkr module with the label facing the sky.

There cannot be metal between the module and sky.

Make all necessary wiring connections.

See “Connecting the device” on page 4 for details.

After 30 seconds with the vehicle ignition ON, check the

indicator lights to make sure the unit has cellular service

and GPS signal. See page 9 for LED status definitions

the device for testing.

Add the device to your Linkr app to configure & test.

See “Testing the device” on page 10.

Write the configuration code & device info on the back

cover of this manual and give it to the vehicle’s owner.

Quick Reference - LINKR-M1 Install Overview

Detailed instructions on the following pages >

WIRE DIAGRAM LOCATED IN

THE CENTER OF THIS

MANUAL (p.6)

USA SMARTPHONE

VEHICLE INTERFACE

LINKR-M1 install guide EN A6.indd 1 5/24/2016 4:00:51 PM

LINKR-M1_EN-4/22/16

Module End View:

LINKR-M1 Module Overview

CEL GPS PWR

BATT

ON OFF

Indicator Lights:

These lights indicate Cellular Service, GPS connectivity, & Power

conditions. For full descriptions of indications, see page 9.

Backup Battery Switch:

The unit is shipped with this switch in the OFF position. Move it to the

ON position AFTER wiring the device.

USB Port:

A USB interface cable is available for purchase. It is rarely needed but

allows you to update the device firmware manually. Otherwise, the user

can update firmware from their phone app (appropriate service plan

required).

Backup Battery

On/Off Switch USB Port

Indicator Lights

LINKR-M1 install guide EN A6.indd 2 5/24/2016 4:00:51 PM

LINKR-M1_EN-04/22/16

Step 2: Determine A Mounting Location

Find a discreet and secure mounting location for the module. Make

sure the module is free from moisture, excessive heat, direct sunlight, or

moving vehicle parts.

- The large white sticker must be facing towards the sky

- There cannot be any metal between the module and the sky

- Mount as high in the dash as possible

- Mount at least 12 inches away from the radio & speakers. The cellular

portion of this device could cause radio interference.

-DO NOT SECURE THE DEVICE UNTIL TESTING IS COMPLETE

Step 3a: Connect The Device - Serial / Data Port Installation

BLACK 4-Pin Serial Data Connector (required):

This allows for a quick plug-in installation when used with a compatible

Omega security or remote start system. Plug this into the matching port

on the host system and program the data port for iDatalink protocol.

Power and Ground are provided by the data port.

YELLOW +12v Ignition input wire (optional):

This is an ignition input wire to the device. It must be connected to an

ignition +12V source. This can be found in the ignition switch harness

or at a fuseblock. Be certain that this wire has +12V with the ignition

key is in the ON position.

NOTE: DO NOT CONNECT IF USING DATA CONNECTOR WITH AN

OMEGA ALARM OR REMOTE START SYSTEM.

BLUE (-) output #1 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary)

configurable for 0.8 second, 3 second, or 10 second pulse. It can be

assigned to most command buttons in the Linkr app.

NOTE: IF YOU ARE NOT CONNECTING TO A DATA PORT AND

HARDWIRING ALL CONNECTIONS, SKIP TO STEP 3B

Plug-N-Play

LINKR-M1 install guide EN A6.indd 3 5/24/2016 4:00:51 PM

LINKR-M1_EN-4/22/16

GREEN (-) output #2 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary)

configurable for 0.8 second, 3 second or 10 second pulse. It can be

assigned to most command buttons in the Linkr app.

ORANGE (-) output #3 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary). It’s

primary function is for ENGINE DISABLE but can be assigned to other

command buttons in the Linkr app if desired.

BROWN/WHITE (-) pulsed alarm trigger input wire (optional):

This input will send a VEHICLE ALARM notification to the user’s phone

when it detects 7 negative pulses within 10 seconds. Connect this to

the alarm’s horn honk output or flashing light output.

NOTE: Omega security systems will send alarm trigger status on the data port, in

which case, this wire is not connected.

BROWN (+) steady alarm trigger input wire (optional):

This input will send a VEHICLE ALARM notification to the user’s phone

when it detects positive voltage (>5vDC) for 7 seconds continuously.

Connect this to the alarm’s positive siren output.

NOTE: Omega security systems will send alarm trigger status on the data port, in

which case, this wire is not connected.

GRAY/BLACK (-) panic button/valet input wire (optional):

This input will send a PANIC notification to the user’s phone when it

detects a negative input for 3 seconds. It can also be used to turn off

the ENGINE DISABLE feature if the device cannot be reached from the

smartphone app. Connect this to the included push-button valet switch.

Connect the other wire of the valet switch to chassis ground.

Step 3a: Connect The Device - Data Port (cont’d)

LINKR-M1 install guide EN A6.indd 4 5/24/2016 4:00:51 PM

LINKR-M1_EN-04/22/16

Step 3b: Connect The Device - Hard Wire Installation

BLACK ground wire (required):

This provides chassis ground to the device. It should be connected

directly to the metal structure of the vehicle. Strip the end of the wire

and crimp on the supplied ring terminal. Route this wire to a solid

grounding point, like an existing bolt in the vehicle and securely ground

the wire.

RED +12v constant power wire (required):

This is the power supply wire to the device. It must be connected to a

FUSED constant +12V source. This can be found in the ignition switch

harness, a fuseblock, or at the vehicle’s battery. Be certain that this wire

has +12V under all circumstances and when the ignition key is in the

ON and OFF positions.

YELLOW +12v ignition input wire (required):

This is an ignition input wire to the device. It must be connected to an

ignition +12V source. This can be found in the ignition switch harness

or at a fuseblock. Be certain that this wire has +12V with the ignition

key is in the ON position.

BLUE (-) output #1 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary)

configurable for 0.8 second, 3 second, or 10 second pulse. It can be

assigned to most command buttons in the Linkr app.

GREEN (-) output #2 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary)

configurable for 0.8 second, 3 second, or 10 second pulse. It can be

assigned to most command buttons in the Linkr app.

NOTE: YOU MUST CUT OFF THE BLACK 4-PIN CONNECTOR

TO HARDWIRE POWER & GROUND CONNECTIONS

LINKR-M1 install guide EN A6.indd 5 5/24/2016 4:00:51 PM

LINKR-M1_EN-4/22/16

NOT USED

FCC ID:YQD-GV300VC

Internal Battery: mAh, 3.7V

Operating Voltage: DC 8 - 32V

Warning!!!

Don't expose to temperature above 60 C.

May explode if disposed of in fire.

16 15 14

13 12 11 10 9

874

653 2 1

PULSE IN (-)

PWR

PANIC IN (-)

OUT1

STEADY IN (+)

OUT2

IGN

GND

OUT3

THIS SIDE TOWARDS SKY

ESTE LADO HACIA EL CIELO

MODEL: LINKR-M1

IIIII |||IIIIIIIIII||||||||||||IIIIIIIIIIIIIIIIII||

IMEI: 012345678912345

CEL GPS PWR

BATT

ON OFF

Indicator Lights

USB Port

(for update by PC- optional cable required)

Backup Battery*

On/Off Switch

Linkr-M1 Wiring Overview

*backup battery unavailable on some versions

LINKR-M1 install guide EN A6.indd 6 5/24/2016 4:00:51 PM

LINKR-M1_EN-04/22/16

BROWN/WHITE (-) Pulsed Alarm Trigger Input (Horn Honk/Light Flash)

YELLOW (+) Ignition Input

Black 4-Pin Data Port Connector

Serial data installation: Program host system for iDatalink

protocol and connect this to the system’s matching data port.

Hardwire installation: Cut and remove connector from harness.

GRAY/BLACK (-) Button Input

BLACK System Ground (-) Input

BLACK/WHITE Serial Data

PINK Serial Data

BLUE (-) Output 1

RED Constant 12v (+) Input

ORANGE (-) Output 3

BROWN (+) Steady Alarm Trigger Input (Alarm Siren)

GREEN (-) Output 2

Panic/Override

Button

Ground

5 A

ORANGE

Starter Interrupt

Socket & Relay

(not included)

To StarterTo Ignition

Switch

WHITE

cut starter

wire

RED

Linkr-M1 Wiring Overview

TYPICAL INSTALLATION

WIRE LEGEND

Hard wire connection required

Supported via DATA port(s)

LINKR-M1 install guide EN A6.indd 7 5/24/2016 4:00:51 PM

LINKR-M1_EN-4/22/16

ORANGE (-) output #3 wire (optional):

This is a negative pulse 150mA output (add a relay if necessary). It’s

primary function is for ENGINE DISABLE but can be assigned to other

command buttons in the Linkr app if desired.

BROWN/WHITE (-) pulsed alarm trigger input wire (optional):

This input will send a VEHICLE ALARM notification to the user’s phone

when it detects 7 negative pulses within 10 seconds. Connect this to

the alarm’s horn honk output or flashing light output.

BROWN (+) steady alarm trigger input wire (optional):

This input will send a VEHICLE ALARM notification to the user’s phone

when it detects positive voltage (>5vDC) for 7 seconds continuously.

Connect this to the alarm’s positive siren output.

GRAY/BLACK (-) panic button/valet input wire (optional):

This input will send a PANIC notification to the user’s phone when it

detects a negative input for 3 seconds. It can also be used to turn off

the ENGINE DISABLE feature if the device cannot be reached from the

smartphone app. Connect this to the included push-button valet switch.

Connect the other wire of the valet switch to chassis ground.

PINK serial data wire (DO NOT CONNECT):

This wire has no function in a hardwire installation.

BLACK/WHITE serial data wire (DO NOT CONNECT):

This wire has no function in a hardwire installation.

Step 3b: Connect The Device - Hard Wire (cont’d)

LINKR-M1 install guide EN A6.indd 8 5/24/2016 4:00:51 PM

LINKR-M1_EN-04/22/16

Step 4: Check The Status Indicator Lights

Using Linkr To Monitor A Home / Building Alarm

Linkr can be installed for direct monitoring of any building alarm. It can

alert the user of any alarm trigger condition and can control quick arm &

disarm functions if the alarm panel supports it.

BLACK ground wire (required):

Connect to the alarm panel (-)12v DC source.

RED +12v constant power wire (required):

Connect to the alarm panel (+)12v DC source.

BLUE, GREEN, & ORANGE (-) output wires (optional):

Typically, you will need to wire relays to connect/disconnect the key input terminals

(aka ‘key zone’) on the panel. In most cases, resistors are required. See the panel

instructions for more info.

BROWN (+) & BROWN/WHITE (-) alarm trigger input wires:

If the siren/bell output is constant when triggered, use the BROWN wire. If the output

is pulsed, use the BROWN/WHITE wire. Be sure the polarity matches, convert with a

relay as needed.

After powering the device, turn on the vehicle ignition and allow a few

minutes to get the proper indicators. Make sure the vehicle is out in the

open so the module has a clear view to the sky.

CEL GPS PWR

BATT

ON OFF

Indicator Lights

LED ON Fast Flashing Slow Flashing OFF

CEL

(green) Transmitting Searching the

cellular network

Connected to

cellular network -

GPS

(blue)

GPS

connected Searching for GPS GPS data error GPS is off

PWR

(red)

Power

connected

& battery is

charged

Power connected,

internal battery is

charging

Power is not

connected, backup

battery is ON.

No Power

LINKR-M1 install guide EN A6.indd 9 5/24/2016 4:00:52 PM

LINKR-M1_EN-4/22/16

Step 4: Test The Device

Install the Linkr app on your smartphone.

search “Omega Linkr” in the app store.

install testing. This can be done from your phone or computer.

Press “add” on the App’s home screen & follow the on-screen

intructions to enter test mode.

Press the edit button next (+ symbol)to the configuration code

field to set the output function options.

See the common configuration codes on page 11.

Enter the device name & mobile phone number

Do not add any other information and press “Save”. You

should receive a text message from the device confirming that

settings have been updated.

Use the command screen to test all connected functions.

IMPORTANT: When the test is successful, enter the the

configuration code at www.omegadealer.com to complete

setup. Write it and the device phone number on the user

activation card and give it to the vehicle owner. You can now

delete the device from your app.

ABOUT INSTALLER TEST MODE:

The Linkr device will remain in test mode until the ‘primary alert receiver’

is added. After it is set, only that phone/user can update it. If it is set

incorrectly and needs to be updated manually, perform the following steps:

1) Turn the Vehicle ignition ON/OFF 5 times within 10 seconds.

You will have 5 minutes to complete step 2.

2) Send the new settings from the app to the device.

You will receive a confirmaiton message if it is successful.

LINKR-M1 install guide EN A6.indd 10 5/24/2016 4:00:52 PM

Inhaltsverzeichnis

Andere Omega Controller Handbücher

Omega

Omega PHCN-37 Fehlerbehebungshandbuch

Omega

Omega CN16Pt Bedienungsanleitung

Omega

Omega CNI16D Bedienungsanleitung

Omega

Omega CNiS32 Bedienungsanleitung

Omega

Omega CN4420 Series Bedienungsanleitung

Omega

Omega CCT-80 Series Bedienungsanleitung

Omega

Omega DPF700 Bedienungsanleitung

Omega

Omega CN32Pt Bedienungsanleitung

Omega

Omega CNiS16D Bedienungsanleitung

Omega

Omega DPF700 Bedienungsanleitung

Omega

Omega HE-XL103 Bedienungsanleitung

Omega

Omega CND3 Series Bedienungsanleitung

Omega

Omega PLATINUM Series Bedienungsanleitung

Omega

Omega Linkr MOBILE Bedienungsanleitung

Omega

Omega i Series Bedienungsanleitung

Omega

Omega CN3440 SERIES Bedienungsanleitung

Omega

Omega i Series Bedienungsanleitung

Omega

Omega i Series Bedienungsanleitung

Omega

Omega CNI16 Bedienungsanleitung

Omega

Omega i-SERIES Bedienungsanleitung

Omega

Omega OMB-PER-488/W95 Bedienungsanleitung

Omega

Omega CN8EPt Bedienungsanleitung

Omega

Omega CNiS16 Bedienungsanleitung

Omega

Omega CSi32 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung