omisa 7125/LI Benutzerhandbuch
Version 1/2013
USE AND MAINTENANCE
INSTRUCTION MANUAL
Machine type:
7125/LI
Serial number:
Year of manufacture:
2020
Version 1/2013
INTENTIONALLY LEFT BLANK
Version 1/2013
Dear costumer,
Thanks for having chosen this product! This instruction manual has
been prepared in order to fully appreciate the high quality of our
product. Inside you will find all the necessary information and
warnings for a safe and proper use. We want to advise you to read it
before proceeding with the operations. We are sure that it will be
easier for you to become familiar with the new device and to use it
for a long time with great satisfaction.
Cordially
Version 1/2013
4
INDEX
INDEX _______________________________________________________ 4
LIMITED WARRANTY ___________________________________________ 5
RETURNS OF GOODS __________________________________________ 5
DISCLAIMER OF LIABILITY ______________________________________ 5
PRODUCT IMPROVEMENT ______________________________________ 5
GENERAL DESCRIPTION OF WELDING MACHINE ___________________ 6
GENERAL WELDING CRITERIA –OPTIMAL USE_____________________ 8
SAFETY ALERTS _____________________________________________ 10
READ AND UNDERSTAND______________________________________ 11
GENERAL SAFETY____________________________________________ 11
WEAR SAFETY EQUIPMENT ____________________________________ 12
HEATER IS NOT EXPLOSION PROOF ____________________________ 12
ELECTRICAL SAFETY _________________________________________ 12
CRUSH POINTS ______________________________________________ 13
HEATER IS HOT ______________________________________________ 13
FUSION PROCEDURES ________________________________________ 13
OVERVIEW __________________________________________________ 14
WHAT IS HEAT FUSION ________________________________________ 14
OPERATION _________________________________________________ 15
LOADING PIPE AND FITTING INTO MACHINE ______________________ 15
HEATER IS NOT EXPLOSION PROOF ____________________________ 15
HEATING THE PIPE AND FITTING________________________________ 16
REMOVE HEATER ____________________________________________ 16
FUSION AND COOLING ________________________________________ 16
SCHEDULED MAINTENANCE ___________________________________ 17
CONTRARY DIRECTION IN USING THE MACHINE __________________ 17
INCONVENIENCE AND SOLUTION _______________________________ 17
DISPOSAL ___________________________________________________ 18
Version 1/2013
5
LIMITED WARRANTY
The manufacturer warrants all its manufactured, sold and repaired products to
be free from defects in materials and workmanship.
The manufacturer obligation under this warranty is limited to free reparation or
free replacement at its factory, within 2 years after shipment, except for
purchased items by third parties (e.g. electronic devices, pumps, switches, etc.),
in which case manufacturer’s warrantyis applied.
Warranty applies when returned freight is prepaid and when it can be proved,
upon examination, that the item is defective.
This warranty does not cover damages to products or components repaired or
altered by anyone other than the manufacturer,damaged due to misuse,
negligence or causality, or not operated or maintained according to the
manufacturer printed instructions and warnings.
This warranty is expressly in lieu of all other expressed or implied warranties.
RETURNS OF GOODS
Buyer agrees not to return goods for any reason, except upon the written
consent of the manufacturer., obtained in advance.
The consent, if given, shall specify the terms and conditions and charges upon
which any such return may be made.
For assistance, all inquiries shall be directed tothe manufacturer.
DISCLAIMER OF LIABILITY
The manufacturer accepts no liability for fusion joints.
We recommend to follow qualified welding procedures using the fusion
equipment.
The manufacturer makes no other warranty of any kind, whatever expressed or
implied. All implied warranties of merchantability and fitness for a particular
purpose, which exceed the foreseen obligation, are hereby disclaimed by The
manufacturer.
PRODUCT IMPROVEMENT
The manufacturer reserves the right to make any changes in or improvements
on its products without incurring any liability or obligation to update or change
previously sold machines and/or accessories thereto.
Version 1/2013
6
GENERAL DESCRIPTION OF WELDING MACHINE
The machine is mainly composed by:
Version 1/2013
7
1 - BASIC MACHINE
The carriage assembly consists of one fixed jaw and two mechanically operated
movable jaws.
It is composed by an aluminium support frame, suitably treated to be resistant
to atmospheric agents, which acts as a guide, on which runs a slide to which it
is firmly anchored in the fitting (pipe).
There is a switch that regulates the correct welding depth.
A device helps the extraction of the polywelder.
The machine has a device suitable to house the closing clamps that are
interchangeable to each other depending on the diameter and the kind of pipe
and / or fitting to be welded. In this way, it is possible to weld the most of pipes,
fittings, reductions and bends on the market.
The movement of the machine is guaranteed from a dedicated tools or by
hands for precise welding.
2- POLYWELDER
The polywelder is mainly constituted by handle and heating plate.
The handle is made in order to assure a comfort, safe and effective grip, thanks
to the material used. It is able to absorb heat produced by the heating plate and
assure a perfect solidity to the whole polywelder.
The heating plate is composed by an aluminium casting with a buried electrical
resistance inside. It is equipped with a thermostat to keep the adjusted
temperature.
The plate has different holes in which can be mounted the bushes through the
supplied service keys and screws.
3 - SET OF BUSHES
The set of bushes is manufactured fully complying with the DVS 2208 standard.
They are supplied in a painted steel box with relevant screws and fastening
keys.
It is of great importance to keep bushes in good conditions in order to assure a
perfect welding. For this purpose, always store bushes properly in their box
when not used and at the end of any job, fastened in their proper housing to not
damage them during transportation. However they should be cleaned before
storing from further welding residual by using a soft cloth or paper.
Make bushes cleaning wearing anti-warm safety gloves, paying great attention.
It is ABSOLUTELY FORBIDDEN using water for cleaning and / or cooling
operation.
Version 1/2013
8
GENERAL WELDING CRITERIA –OPTIMAL USE
This welding machine is intended to weld pipes and / or fittings in thermoplastic
material; any other kind of use is to be considered not proper and dangerous
and shall absolute exclude the manufacturing company from any kind of
responsibility.
The welding machine 7125/LI is adjusted to be used EXCLUSIVELY with the
extractable polywelder 10125/TF with the bushes supplied as standard
equipment; the use of any other kind of polywelder and / or bushes do NOT
assure a correct welding; and shall absolute exclude the manufacturing
company from any kind of responsibility.
The welding operation with the machine ART. 7125/LI is done inserting the pipe
inside the fitting, after heating the outside part of pipe and the inner part of fitting
for a stated period of time, by using the extractable polywelder 10125/TF with
bushes.
It would be good rule, before doing all welding operations, to check some
matters:
- Carefully check the efficiency and the perfect running of safety device.
- Check the operation of the mobile parts, make sure they are not locked.
- Check that all parts of the machine are mounted correctly.
- Make sure that all conditions that could affect the normal operation of the
machine and the welding are acceptable.
It is recommended to place the equipment to be able to operate freely and into
the required time, in order to avoid wrong operations that could compromise the
good welding result. It would be good rule to make some trial tests before
proceeding.
Version 1/2013
9
TECHNICAL FEATURES:
Welding capacity: Ø32 –Ø125
Weight with battery and yokes: approx. 12.5kg
Weight complete set: approx. 17.5kg
Outer dimension: approx 455 x 390 x 265 mm
Length of machine: approx 450 mm
Height of machine with yokes: approx. 265 mm
Width of the machine with yokes:approx 390 mm.
Max torque: 44Nm
Battery voltage: 12V/2 Ah
Battery loading time: approx. 1h
Idle speed: 1200 min-1
Compression speed Ø125 mm: < 9 sec.
Tool machine: Makita or equivalent rotary hammer
Version 1/2013
10
SAFETY ALERTS
This hazard alert signal appears in this instruction manual.
When you see this signal, carefully read its meaning.
YOUR SAFETY IS AT STAKE.
The hazard alert signal is usually accompanied by
these words: DANGER, WARNING and CAUTION.
DANGER Indicates a hazardous situation that, if not
avoided, will result in death or seriously
injury.
WARNING Indicates a hazardous situation that, if not
avoided, could result in death or serious
injury.
CAUTION Indicates a hazardous situation that, if not
avoided, may result in minor or moderate
injury.
In this manual you should pay attention to another
word:
NOTICE Can keep you from doing something that might damage the
machine or someone’s property. It may also be used to alert
against unsafe practices.
Inhaltsverzeichnis
Andere omisa Schweißsystem Handbücher
Beliebte Schweißsystem Handbücher anderer Marken
TAFA
TAFA 30*8B35 Bedienungsanleitung
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung
ESAB
ESAB Buddy Arc 145 Bedienungsanleitung
CIGWELD
CIGWELD 636804 Kurzanleitung
Red-D-Arc
Red-D-Arc DC-400 Bedienungsanleitung
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung
