Omnicomm Smart 3.0 Bedienungsanleitung

Smart 3.0 Terminal

User manual

11.02.2020

Contents

General Information

Installation

Installing a SIM Card

Output Connectors

Power supply and Ignition key

Terminal

General Configuration Information

Omnicomm Configurator

Remote Configuration Server (RCS)

Configuring Operational Parameters

GPRS Connection

Collecting Data

Communication Server Connection

Speed source selection

Ignition key status

Engine RPM

Accelerometer

Utility Functions

Restarting Terminal

Setting Up Password for Configuring Parameters

Operational Set-up For Remote Configuration Server

Identifying Terminal's SIM Card Number

Additional equipment

Fuel level sensors

Universal Inputs

Omnicomm LLD Indicator

Panic Button

CAN bus

Technical Specifications

SMS commands

Smart 3.0 Terminal

General Information

Omnicomm Terminals are the on-board equipment designed to collect data on the

state of the vehicle and transmit these data to Omnicomm Online or a third-party fleet

monitoring system of choice.

Terminal key functions are:

- Identifying and recording location, speed, and direction of travel of a vehicle;

- Reading and sorting values received from the fuel level sensors and a wide range of

other connected equipment;

- Remote control of any additional equipment connected to the system;

- Non-volatile data storage;

- Transmitting data to Omnicomm Online and/or other fleet monitoring system of

choice.

Omnicomm Terminal modifications differ from one another by design and type of

equipment that can be connected to them. This User Manual describes the

Omnicomm Smart Terminal range.

Safety Recommendations

Please take all the necessary safety measures and comply with all relevant standards

and regulations when installing the equipment.

Installation

Installing a SIM Card

Before installing a SIM card please disable the PIN code request upon start-up. In

order to do that, simply insert the SIM card into any cell phone and disable the PIN

code request according to the telephone operating specifications.

1. Use a pointed object to press a button on the Terminal's front panel. This will eject a

SIM card holder.

2. Remove the SIM card holder from the slot and install the SIM card in it with the

contact side up.

General Information

3. Install the SIM card holder back into the slot (see the image below).

It is possible to custom-order an option for installing a SIM chip.

Output Connectors

Omnicomm Smart Terminal

X1 connector:

Output Connectors

Contact

number

Signal Name Designation Wire Colours Inside

Cable

1 Ground (negative) for power

supply

General

(signal)

White

2 Input RPM Tachometer Blue

3 Not used NC

4 Not used NC

5 Line B: RS-485 LLS B RS-485 LLS Blue-white

6 CAN L CAN L Violet-white

7 On-board power voltage Power supply Red

8 Ignition key IGN Yellow

9 Universal input Input 1 Black

10 Not used NC

11 Line A RS-485 LLS A RS-485 LLS Orange-white

12 CAN H CAN H Violet-orange

Power supply and Ignition key

Perform the connection of Omnicomm Smart 3.0 Terminals without the main switch

according to the diagrams below:

Power supply and Ignition key

Before the main switch:

Terminal

The Omnicomm Terminal must be installed inside the vehicle cabin or inside a

specially designed electrical equipment box: weather- and precipitation-proofed and

fixed on the vehicle. Drill 4 mounting holes, 4 mm in Ø.

Here is an example for Omnicomm Smart Terminals:

Terminal

Install the Terminal and fix it by using self-tapping screws.

General Configuration Information

Omnicomm Configurator There are two ways to configure Omnicomm Terminals: 1.

Via the Omnicomm Configurator upon connecting the Terminal to a personal

computer; 2. Via the Remote Configuration Server (RCS).

Initial Terminal's configuration must be performed via Omnicomm Configurator

program.

Omnicomm Configurator

1. Connect the Terminal to the personal computer with a USB cable. 2. Install and run

the Omnicomm Configurator. You will be taken to the following screen:

General Configuration Information

3. Select the 'Configuring the Terminal' operation mode.

Remote Configuration Server (RCS)

Open your browser and enter 'http://config.omnicomm.ru:9911/#en' in the URL bar to

connect to the configuration server. Then, the window will open.

Remote Configuration Server (RCS)

To add the terminal, do the following:

1. Enter the Terminal's identification number in the 'Terminal ID' field.

2. Enter the password that you selected for the Terminal when configuring it via the

Omnicomm Configurator in the 'Password' field.

3. Click on the '+' button.

Configuring Operational Parameters

GPRS Connection

Open the “Settings” menu and select the 'Connection' tab. Now refer to “GPRS

Settings”:

Configuring Operational Parameters

Inhaltsverzeichnis

Andere Omnicomm Touch-Terminal Handbücher

Omnicomm

Omnicomm Smart 3.2 Bedienungsanleitung

Omnicomm

Omnicomm OKO Bedienungsanleitung

Omnicomm

Omnicomm OKO 3.0 Bedienungsanleitung

Omnicomm

Omnicomm Profi Bedienungsanleitung

Omnicomm

Omnicomm Profi 2.0 Bedienungsanleitung

Omnicomm

Omnicomm Smart Bedienungsanleitung

Omnicomm

Omnicomm Optim 3.0 Bedienungsanleitung

Omnicomm

Omnicomm OBDII Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung