Omnimount PLAY70 Bedienungsanleitung
PN:888-45-254-W-01 revF 05/15 1 of 25
INSTRUCTION MANUAL
PLAY70
INTERACTIVE TV MOUNT
Reduce.Reuse.Recycle
CAUTION!
MAXIMUM SCREEN SIZE
CAUTION!
MAXIMUM WEIGHT CAPACITY
70 LBS
31.8 KG
60+”
NEED HELP? PLEASE CALL
DISCLAIMER - WARNING INFORMATION
Disclaimer – OmniMount Systems, Inc. has extended every effort to ensure to accuracy and completeness of this manual. However, OmniMount Systems, Inc. does not
claim that the information covers all installation or operational variables. The information contained in this document is subject to change without notice or obligation of
any kind. Regarding the information contained herein, OmniMount Systems, Inc. makes no representation of warranty, expressed or implied, and assumes no responsibility
for accuracy, sufficiency, or completeness of the information contained in this document.
Wall Mounts
WARNING: FAILURE TO READ, THOROUGHLY UNDERSTAND, AND FOLLOW ALL INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY, DAMAGE TO PERSONAL
PROPERTY, OR VOIDING OF FACTORY WARRANTY!
It is the responsibility of the installer to ensure all components are properly assembled and installed using the instructions provided. If you do not understand these in-
structions or have any questions or concerns, please contact customer service at 1-800-668-6848 or [email protected].
Do not attempt to install or assemble this product if the product or hardware is damaged or missing. In the event that replacement parts or hardware are needed, please
contact Customer Service at 1-800-668-6848 or [email protected]. International customers needing assistance should contact the Dealer from which they purchased
the product.
The included hardware is designed for use on vertical walls constructed of wood studs or solid concrete. A wood stud wall is defined as consisting of a minimum of
2x4 wooden studs (2” wide by 4” deep) with a maximum of 5/8” drywall. The included hardware is not designed for use with metal studs or cinderblock walls. If you’re
uncertain about the construction of your wall, then please consult a qualified contractor or installer for assistance. For a safe installation, the wall you are mounting to must
support 4 times the weight of the total load. If not, then the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure
and hardware used in any installation method will safely support the total load.
PN:888-45-254-W-01 revF 05/15 7 of 25
CONTENTS
Wall Kit ST8x3 697-688-00
Part Quantity Description
W-A 3 Lag Bolt
W-B 3 Round Washers
W-C 3 Wall Anchor
Specialty Hardware kit 697-640-00
Part Quantity Description
P-A 1 Philips Screw
P-B 4 Round Head Screws
P-C 8 Nuts
Screws/Hardware For Flat Panel 697-613-00
Part Quantity Description
M-A 4 Philips screws M4 x 15mm
M-B 4 Philips screws M4 x 30mm
M-C 4 Philips screws M5 x 15mm
M-D 4 Philips screws M5 x 30mm
M-E 4 Philips screws M6 x 15mm
M-F 4 Philips screws M6 x 30mm
M-G 4 Philips screws M8 x 15mm
M-H 4 Philips screws M8 x 30mm
M-I 4 Round spacers M6-M8 x 5mm
M-J 4 Round spacers M6-M8 x 10mm
M-K 4 Round washers M4-M5
M-L 4 Round washers M6-M8
CONTENTS
Part Quantity Description
11 Wall Plate
21 Arm/Wall Plate Hardware
32 Wall Plate Covers
41 Rear Arm Cover
51 CFT Arm
61 200x200 VESA Monitor Plate
74 Spider Adapters
1
3
4
56
7
Cable Wrap Kit 697-701
Part Quantity Description
P-D 1 Cable Wrap
BOP 699-633
Part Quantity Description
P-L 2 Zip Ties
P-J
P-Q
10mm
8mm
P-F
P-K
P-I
P-H
P-G
P-M
2
PN:888-45-254-W-01 revF 05/15
8 of 25
CAUTION!
MAXIMUM SCREEN SIZE
CAUTION!
MAXIMUM WEIGHT CAPACITY
70 LBS
31.8 KG
60+”
Tools Needed
Tools Needed
13mm and 8mm
PN:888-45-254-W-01 revF 05/15 9 of 25
STEP 1 - Placement of Arm on the Wall
INSTRUCTIONS
RANGE OF MOTION
SPACE REQUIREMENTS
front
front
front
side
top top
Horizontal Studs
Distance from the Wall
If there is no available stud for
desired TV location, you may
want to insert horizontal studs
into your wall at the desired
mounting location.
28.8” (731 mm) +
Thickness of TV
25.2” (640 mm) + Thickness
of TV
Horizontal Space Requirements
40.49” (1028 mm) + Width of TV*
Vertical Space
Requirements
20.49” (520 mm) + Height
of TV*
*Space requirement dimensions assume mounting holes are centered on the TV.
1. MOUNTING CONSIDERATIONS:
• Wall Mount Bracket MUST be attached to a stud or solid concrete. DO NOT attach this product to hollow wall or any other conguration.
• Make sure Arm will have desired unobstructed range of motion: up-down, side-to-side, in-out (see section RANGE OF MOTION).
• Make sure cables will reach their destinations with enough remaining slack to allow Arm full range of motion.
• Use the RANGE OF MOTION section to familiarize yourself with the movements of this product. Take into account that the TV will change
location from Side-to-Side when pulled out from the wall.
• Use the SPACE REQUIREMENTS section for maximum measurements of this products full range of motion.
• If there is no available stud for desired TV location, you may want to insert horizontal studs into your wall at the desired mounting
location (see “Horizontal Studs”image below).
2. CHOOSE YOUR DESIRED TV LOCATIONS:
Choose your desired TV locations when stowed and extended. Note the TV will move side-to-side when pushing it into and pulling it
out from the wall as well as lifting it up and lowering it down. This step requires an understanding of this products Range of Motion (see
section RANGE OF MOTION).
19.16”
(487mm)
20.4”
(518mm)
16.83”
(428mm)
20.13”
(511mm)
.98”
(25mm)
1.38”
(35mm)
10.63”
(270mm)
Front view with arm pushed back against the wall.
Top view showing range of motion when pulled out from
the wall.
PN:888-45-254-W-01 revF 05/15
10 of 25
STEP 2 - Wood Stud Installation
1
2
a
a
bc
Wood Stud Mount
cd
W-A
W-B
1
b
7/32 x 2.75"
5.5mm x 70mm
PN:888-45-254-W-01 revF 05/15 11 of 25
STEP 2 - Solid Wall Installation
Solid Wall Mount
1abc
2a
c
b
d
W-A
W-B
W-C
3/8 x 2.75"
9.5 - 10mm x 70mm
PN:888-45-254-W-01 revF 05/15
12 of 25
STEP 3
3ab
cd
1
2
5
P-F
P-J
P-K
P-I
16mm Bearing
P-G
25mm Washer
P-M
P-F
65mm Washer
P-M
P-H
Spring Disc
NOTE: Part# P-H must
be concave face down for
proper assembly.
PN:888-45-254-W-01 revF 05/15 13 of 25
STEP 4
4
100 x 200
200 x 200
200 x 300
200 x 400
300 x 300
300 x 400
400 x 400
600 x 400
300 x 200
400 x 200
200mm (7-7/8”)
400mm (15-3/4”)
300mm (11-13/16”)
600mm (23-5/8”)
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
400mm (15-3/4”)
300mm (11-13/16”)
400mm (15-3/4”)
300mm (11-13/16”)
400mm (15-3/4”)
400mm (15-3/4”)
300mm (11-13/16”)
200mm (7-7/8”)
A
B
C
D
PN:888-45-254-W-01 revF 05/15
14 of 25
OR
OR
OR
OR
OR
OR
OR
100 x 200
200 x 200
200mm (7-7/8”)
100mm (3-15/16”)
200mm (7-7/8”)
200mm (7-7/8”)
A
M-A M-B
M-C
M-D
M-E
M-F
M-G M-H
M-K
M-L
M-I
M-J
6
WARNING! PLEASE SELECT THE PROPER SCREW LENGTH FOR YOUR FLAT PANEL
BY HAND TIGHTENING TO CHECK YOUR FLAT PANELS THREAD DEPTH.
STEP 5-A - Monitor Installation
Andere Handbücher für PLAY70
1
Inhaltsverzeichnis
Andere Omnimount TV-Halterung Handbücher
Omnimount
Omnimount IQLP60F Bedienungsanleitung
Omnimount
Omnimount Wishbone Series Bedienungsanleitung
Omnimount
Omnimount LEDW60 Bedienungsanleitung
Omnimount
Omnimount 1100167 Bedienungsanleitung
Omnimount
Omnimount Modena 47FP Bedienungsanleitung
Omnimount
Omnimount VB60LED Bedienungsanleitung
Omnimount
Omnimount NC80-F Bedienungsanleitung
Omnimount
Omnimount UL10333 Bedienungsanleitung
Omnimount
Omnimount 10040 Bedienungsanleitung
Omnimount
Omnimount CI80FMX Bedienungsanleitung
Omnimount
Omnimount PLAY40 Bedienungsanleitung
Omnimount
Omnimount 10034 Bedienungsanleitung
Omnimount
Omnimount NC125C Bedienungsanleitung
Omnimount
Omnimount VFL OM10322 Bedienungsanleitung
Omnimount
Omnimount OL200FT Bedienungsanleitung
Omnimount
Omnimount LEDP75 Bedienungsanleitung
Omnimount
Omnimount 1004164 Bedienungsanleitung
Omnimount
Omnimount TVM-21 Bedienungsanleitung
Omnimount
Omnimount ULPC-X Bedienungsanleitung
Omnimount
Omnimount NC200-T Bedienungsanleitung
