Omnisense Systems Sentry MK4 Bedienungsanleitung

User Guide

Part No: SM4-OMS-384

Ver 3.0

MASS FEVER SCREENING SYSTEM

Contents

01 - Important Information .................................................................................................... 4

1.1 For your safety....................................................................................................................................................4

1.2 Compliance .........................................................................................................................................................5

1.3 Notices..................................................................................................................................................................6

02 - Introduction..................................................................................................................... 7

2.1 What’s in the Package ......................................................................................................................................7

2.2 Optional Items ....................................................................................................................................................8

2.3 Deployment Site Selection..............................................................................................................................9

2.4 Screening Considerations...............................................................................................................................9

2.5 System Positioning ............................................................................................................................................10

2.6 System Connection ...........................................................................................................................................11

2.7 System Setup (with Pedestal) .........................................................................................................................12

2.8 System Overview...............................................................................................................................................14

03 - Getting Started................................................................................................................ 15

3.1 Powering up ........................................................................................................................................................15

3.2 User Interface .....................................................................................................................................................15

04 - Conﬁguring the System................................................................................................. 16

4.1 Login Access Level............................................................................................................................................16

4.2 Operating Menu .................................................................................................................................................16

4.3 TRS (Thermal Reference Source) ..................................................................................................................17

4.3.1 Setting the TRS ......................................................................................................................................17

4.3.2 Trigger ......................................................................................................................................................18

4.3.3 Temperature Scale................................................................................................................................18

4.3.4 TRS ID.......................................................................................................................................................18

4.3.5 Scan .........................................................................................................................................................18

4.4 Camera ................................................................................................................................................................19

4.4.1 Zone..........................................................................................................................................................19

4.4.2 Mask 1 and 2...........................................................................................................................................20

4.4.3 Display Palette .......................................................................................................................................21

4.4.4 NUC ..........................................................................................................................................................21

4.5 Systems Setting..................................................................................................................................................22

4.5.1 Audio Alarm ............................................................................................................................................22

4.5.2 Time Setting............................................................................................................................................23

4.6 User .......................................................................................................................................................................23

05 - User Level Access........................................................................................................... 24

06 - Deployment Layout ........................................................................................................ 25

07 - Recommended Screening Process and Best Practices............................................. 28

7.1 Items to Prepare.................................................................................................................................................28

7.2 Locations to Prepare.........................................................................................................................................28

7.3 Recommended Screening Process...............................................................................................................28

08 - Advanced Functions ...................................................................................................... 29

8.1 24HR Record.......................................................................................................................................................29

8.2 Rec on Detect .....................................................................................................................................................29

8.3 Storage Info.........................................................................................................................................................30

8.4 Export Video ......................................................................................................................................................31

8.5 IP Setting..............................................................................................................................................................32

8.6 Firmware Update ..............................................................................................................................................33

8.7 Ethernet Port .......................................................................................................................................................34

8.8 HTML Login .........................................................................................................................................................34

8.8.1 Admin Access (HTML)..........................................................................................................................35

8.8.2 Security ....................................................................................................................................................35

8.8.3 Video Streaming....................................................................................................................................36

09 - Troubleshooting Guide .................................................................................................. 37

10 - Speciﬁcations................................................................................................................... 39

Product installation and operation

This product must be installed and operated in accordance with the instructions provided. Failure to do so

could result in injuries, damage to the hardware and/or poor product performance.

Power supply voltage

Connecting this product to a voltage supply greater than the speciﬁed maximum rating may cause permanent

damage to the unit. Refer to the technical speciﬁcations for voltage rating.

Power supply protection

When installing this product, ensure the power source is adequately protected by means of a suitably rated

fuse or automatic circuit breaker.

Service and maintenance

This product contains no user serviceable components. With the exception of regular cleaning, please refer all

maintenance and repair to Omnisense Systems. Unauthorised repair will void the manufacturer warranty.

Using the supplied cables

Do not cut or extend all supplied cables unless doing so is detailed in the installation guide.

Do not open or disassemble

The unit is factory sealed to protect against atmospheric humidity, suspended particulates and other

contaminates. Do not open the camera or TRS unit for any reason. Disassembly of the camera or TRS unit or

any tampering can cause permanent damage to the system and will void the manufacturer warranty.

Warranty registration

To register your Omnisense Systems product ownership, please visit omnisense-systems.com and register

online. It is important that you register your product to receive full warranty beneﬁts.

01 - Important Information

1.1 For your safety

To prevent damage to your Omnisense Systems product or injury to yourself or to others, read the following

safety precautions in their entirety before using this equipment. Keep these safety instructions where all those

who use the product will read them.

WARNINGS

The consequences that could result from failure to observe the precautions listed in this

section.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful interference

2. This device must accept any interference received, including interference that may cause

undesired operation.

FCC ID: 2AB6YHM-1011V1

CE Marking

CE marking on this device represents the device are manufactured and delivered in accordance with

the following directives:

2014/30EU Electromagnetic Compatibility

2014/35/EU Low Voltage Directive (Power Supply)

2012/19/EU Waste Electrical and Electrical Equipment

The original Declaration of Conformity certiﬁcate may be viewed on the product page at

www.omnisense-systems.com.

Product Disposal

In accordance with European Union (EU) Waste Electrical and Electronic Equipment Directive

2002/96/EC (WEEE), all Electrical and Electronic Equipment (EEE) products labeled with the “crossed

out wheeled bin” either on the product itself or in the product literature is to be collected separately.

The following applies only to users in European countries:

• This product is designated for separate collection at an appropriate collection point. Do not

dispose of as household waste.

• Separate collection and recycling help to conserve natural resources and prevent negative

consequences for human health and the environment that might result from incorrect

disposal.

• For more information, contact the retailer or the local authorities in charge of waste

management.

1.2 Compliance

1.3 Notices

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form,

by any means, without Omnisense Systems’ prior written permission. Names and marks appearing on the

products herein are either registered trademarks or trademarks of Omnisense Systems and/or its subsidiaries.

All other trademarks, trade names, or company names referenced herein are used for identiﬁcation only and

are the property of their respective owners.

Due to our policy of continuous product improvement, Omnisense Systems reserves the right to change the

speciﬁcations of the hardware and software described in this guide at any time and without prior notice.

Omnisense Systems will not be held liable for any damages resulting from the use of this product.

While every eort has been made to ensure that the information in this guide is accurate and complete, we

would appreciate it were you to bring any errors or omissions to the attention of the Omnisense Systems

representative in your area.

Please scan the QR code or check our website at www.omnisense-systems.com to

ensure you have the latest version of the documentation for your product.

Omnisense Systems Pte Ltd

8 Penjuru Lane,

Singapore 609189

T: +65 6844 3191

Omnisense Systems USA Inc

2800 W State Rd 84, #113, Fort Lauderdale,

FL 33312, United States

T: +1 (954) 316-6230

02 - Introduction

Thank you for choosing the Sentry MK4 Mass Fever Screening System (MFSS). The Sentry MK4 MFSS comes

with all the components ready to install and operate, making it the most user-friendly Mass Fever Screening

System available. We would like to help you create an eective screening operation with our system that

oers maximum protection. Therefore, it is recommended to read through the user guide before setting up

the system. This guide will provide you with the information you need to set up and operate the system.

2.1 What’s in the Package

Your system ships with all the components shown below. Ensure that you have received all the components

and contact Omnisense Systems if any of the items is missing.

Monitor Power

Supply

TRS power

Supply

Console

Power Supply

HDMI CableUSB CableNetwork Cable

Camera TRS

Storage Case24” LED Display Monitor

Console

2.2 Optional Items

The mobile pedestal and TRS tripod stand are optional items and may not ship with your system. If you have

ordered the mobile pedestal, the following cables are pre-installed in the mobile pedestal:

1. Network Cable

2. USB Cable

3. Monitor Power Supply

4. Main Console Power Supply

Mobile Pedestal

(optional)

TRS Tripod Stand

(optional)

Complete Sentry MK4

Setup

Storage

case

LED Display

Monitor

TRS

Camera

Console

TRS Tripod

Holder

TRS Tripod

Stand

2.3 Deployment Site Selection

A successful screening operation begins with site selection. Select a deployment location with a natural funnel

that channels human trac into a manageable and controlled ﬂow. This could be a doorway or a passageway.

If such an area is not available, create a passage with barriers. As the system only screen persons facing the

camera, we recommend outgoing trac be channeled through other paths. In order for the system to be at its

peak performance, outgoing trac ﬂow should bring screened persons towards system operators, disperse

only after passing them.

Ideally, persons to be screened should face the camera directly. This, however, may not be practical in many

deployment sites. You may set up the system to screen persons at an angle, but not exceeding 45 degrees.

As the system is very sensitive to heat signatures, ensure the camera is not pointing at the hot background.

These could be parking lots, roads, passing trac or even hot windows. Failure to observe these guidelines

may result in a false alarm trigger.

If there are small areas of hot objects that cannot be avoided, use the onboard Mask function to exclude that

area or Zone function to select a speciﬁc area to screen.

As much as the system can function under a very wide environmental range, eective screening can only be

conducted in environmental temperature between 61°F - 91°F (16°C - 33°C). Extended range of up to 100°F

(38°C) is possible but may result in longer stabilization time and reduced accuracy.

2.4 Screening Considerations

The Sentry MK4 MFSS is designed to screen persons for elevated skin temperature. Therefore, consideration

needs to be given to ensure the person’s skin is not adversely aected by the external environment.

• Persons should not be screened under direct sunlight.

• Sucient time should be provided for persons to cool down (or warm-up if the environment is cold)

• As the system cannot screen what it cannot see, sucient areas exposing face is required.

Hair and shoulder will trap and hold heat for some time, these signatures may trigger the alarm and

cause false alert. To minimize false alert, ensure there is sucient time to condition people coming in

from under direct sunlight.

10 - 16ft (3-5m) screening distance

Recommended 10 - 16ft (3 - 5m) distance between Camera and TRS,

maximum 23ft (7m).

Camera TRS

Position the TRS

Set up the tripod or place the TRS on a suitable

platform. The TRS has to face the camera and

positioned WITHIN the camera’s ﬁeld of view. You

may verify this with the live camera video feed.

Subsequently, check the trac ﬂow at the intended

screening area and adjust the camera/TRS position

as necessary. Check for trip hazards.

Position the camera unit

Setup the mobile pedestal (or other suitable

mounting/placement platform) and position the

camera above human height of 6ft 7in – 7ft 3in

(200  220cm). The subjects to be screened should

be walking towards the camera unit. Position and

orientate the camera as necessary.

2.5 System Positioning

The illustration below shows how the Sentry MK4 components should be positioned in the screening area.

For mobile setup, we recommend the system to be installed on our custom-designed mobile pedestal. This

pedestal is designed with features that are best suited for the Sentry MK4 MFSS.

Other options are possible, the camera and TRS use industry-standard tripod mounting screw thread. The

console uses industry-standard 75x75mm VESA mount.

For prolong deployment, we suggest the system be ﬁxed mounted to permanent structures of possible.

Camera and TRS can be mounted with any industrial standard CCTV mounting brackets. The system is

designed for continuous duty and can operate on a 24/7 basis without damage.

6ft 7in - 7ft 3in

(200 - 220cm)

5ft 11in - 6ft 7in

(180 - 200cm)

In general, the trigger alarm will be activated if the signal between the camera unit and TRS is blocked

(e.g. human trac). Setting the camera unit and TRS at a height that ensures a clear line of sight between

them during screen operation will prevent this from happening.

Inhaltsverzeichnis

Andere Omnisense Systems Wärmebildkamera Handbücher

Omnisense Systems

Omnisense Systems Ulysses mini Bedienungsanleitung

Beliebte Wärmebildkamera Handbücher anderer Marken

Hikmicro

Hikmicro B20 Bedienungsanleitung

FLIR

FLIR E-EST Series Bedienungsanleitung

FLIR

FLIR M-Series Bedienungsanleitung

BST

BST BT-72 Bedienungsanleitung

FLIR

FLIR G300 pt Series Bedienungsanleitung

CBC

CBC EN7-S02T Bedienungsanleitung

Satir

Satir YRH600 Bedienungsanleitung

TESTO

TESTO 882 Bedienungsanleitung

TECPEL

TECPEL TIG-320 Bedienungsanleitung

SKF

SKF TKTI 21 Bedienungsanleitung

TESTO

TESTO 885 Bedienungsanleitung

InfiRay

InfiRay AT300 Series Bedienungsanleitung

InfiRay

InfiRay AT Series Bedienungsanleitung

FLIR

FLIR X6530sc Series Bedienungsanleitung

Videotec

Videotec MAXIMUS MVXT Bedienungsanleitung

Guide Sensmart

Guide Sensmart D384M Bedienungsanleitung

NBN

NBN FLIR A6 Series Bedienungsanleitung

WORKSWELL

WORKSWELL SAFETIS Bedienungsanleitung