Omron GRT1-CRT - 05-2008 Bedienungsanleitung

CompoNet Communications Unit

Cat. No. W476-E1-01

SmartSlice

GRT1-CRT

OPERATION MANUAL

SmartSlice

GRT1-CRT

CompoNet Communications Unit

Operation Manual

Produced May 2008

Introduction

Thank you for buying a SmartSlice CompoNet Communications Unit.

The CompoNet Communications Unit is an interface unit which complies with the CompoNet

standard. It connects SmartSlice I/O Units to a CompoNet Master Unit.

Be sure you understand the functions and performance of the Units fully before you use them.

Intended Audience

This manual is for the personnel below. This personnel must understand electrical systems (must

be an electrical engineer or the equivalent).

Personnel responsible for the selection of FA systems

Personnel responsible for the designs of FA systems

Personnel responsible for the installation of and connections in FA systems

Personnel responsible for the management of FA systems

Precaution

This manual contains data which is necessary for you to use a CompoNet Communications Unit.

Read and understand this manual fully before you use the CompoNet Communications Unit. After

you read this manual, keep it in a safe location where it will be available for use when necessary.

Be sure that the end user of the CompoNet Communications Unit has this manual.

Read and Understand this Manual

Please read and understand this manual before using the product. Please consult your OMRON

representative if you have any questions or comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship

for a period of one year (or other period if specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING

NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE

PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS

DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR

INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE

PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR

STRICT LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on

which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS

REGARDING THE PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS

WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO

CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Read and Understand this Manual

vii

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to

the combination of products in the customer's application or use of the products.

At the customer's request, OMRON will provide applicable third party certification documents identifying

ratings and limitations of use that apply to the products. This information by itself is not sufficient for a

complete determination of the suitability of the products in combination with the end product, machine,

system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not

intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the

uses listed may be suitable for the products:

• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions

or uses not described in this manual.

• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical

equipment, amusement machines, vehicles, safety equipment, and installations subject to separate

industry or government regulations.

• Systems, machines, and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR

PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO

ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND

INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

Read and Understand this Manual

viii

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other

reasons.

It is our practice to change model numbers when published ratings or features are changed, or when

significant construction changes are made. However, some specifications of the products may be

changed without any notice. When in doubt, special model numbers may be assigned to fix or establish

key specifications for your application on your request. Please consult with your OMRON representative

at any time to confirm actual specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when

tolerances are shown.

PERFORMANCE DATA

Performance data given in this manual is provided as a guide for the user in determining suitability and

does not constitute a warranty. It may represent the result of OMRON's test conditions, and the users

must correlate it to actual application requirements. Actual performance is subject to the OMRON

Warranty and Limitations of Liability.

ERRORS AND OMISSIONS

The information in this manual has been carefully checked and is believed to be accurate; however, no

responsibility is assumed for clerical, typographical, or proofreading errors, or omissions.

Safety Precautions

Safety Indications

The indications below are used in this manual for safety precautions which are necessary to use the

CompoNet Communications Unit safely. The contents of these safety precautions are important. Al-

ways obey them.

These are the indications for safety precautions.

• “Precautions for Safe Application” shows the operations that you must do or

not do to use the product safely.

• “Precautions for Correct Application” shows operations that you must do or not

do to make sure that the product operates, prevent malfunctions, and prevent

bad effects on performance and functions.

WARNING

Caution

Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

Additionally, there may be severe property damage.

Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury, or property

damage.

Precaution for

Safe Usage

Precaution for

Correct Usage

Safety Precautions

Descriptions of Symbols

This symbol shows operations that you must not do.

The specified operation shows in the circle.

This example shows “do not disassemble.”

This symbol shows precautions (including warnings).

The specified operation shows in the triangle.

This example shows a general precaution.

This symbol shows operations that you must do.

The specified operation shows in the circle.

This example shows a general precaution for something that

you must do.

WARNING

Do not try to disassemble a Unit or touch the terminal block while

the power is ON. Doing this can cause electrical shock.

Make sure that the voltage and current input to the Units are in the

specified ranges. If the voltage and current are not in the specified

ranges, there can be Unit malfunctions or fire.

Turn OFF the I/O power supply to a SmartSlice I/O Unit before you

replace it with the online replacement procedure. If there is external

power to a terminal for a Relay Output Slave, for example, turn OFF

the external power before you replace the SmartSlice I/O Unit. If

you replace a Slave I/O Unit with the power ON, incorrect outputs,

incorrect inputs, or electric shock can occur.

Safety Precautions

Apply safety measures in external circuits (that is, not in the Smart-

Slice I/O Terminal) to keep safety in the system. These measures

must keep safety if a malfunction in the control system or other ex-

ternal factor which has an effect on the control system causes a

problem. Include the items below. Not doing this can cause serious

accidents.

• There must be emergency stop circuits, interlock circuits, limit cir-

cuits, and other safety measures in external control circuits.

• The SmartSlice outputs can stay ON or OFF because of welding

or burning of the output relays, or destruction of the output tran-

sistors. As a countermeasure for such errors, there must be ex-

ternal safety measures to keep safety in the system.

• The SmartSlice I/O Terminal will continue operating when one or

more I/O Units are missing from the SmartSlice I/O Terminal. The

other I/O Units will continue the control operations, including the

control of the outputs. As a countermeasure for such errors, there

must be external safety measures to keep safety in the system.

The CPU Unit refreshes I/O when the program is stopped in PRO-

GRAM mode. Fully make sure that it is safe before changing the

status of bits or words in memory allocated to Output Slaves, Spe-

cial I/O Units, or CPU Bus Units. If you change the bits or words al-

located to a Slave or Unit, you could cause incorrect operation of

the loads connected to the Slave or Unit. The operations below will

change memory status.

• Transferring I/O memory data to the CPU Unit from a Program-

ming Device

• Changing present values in memory from a Programming Device

• Force-setting or force-resetting bits from a Programming Device

• Transferring I/O memory files from a Memory Card or EM file

memory to the CPU Unit

• Transferring I/O memory from a host computer or from a PLC on

a network

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Konferenzsystem Handbücher

Omron

Omron V680 - 2 Bedienungsanleitung

Omron

Omron GRT1-PNT - 2 Bedienungsanleitung

Omron

Omron SYSDRIVE MX2 SERIES Bedienungsanleitung

Omron

Omron V640 Bedienungsanleitung

Omron

Omron E3NW-CCL Bedienungsanleitung

Omron

Omron C200HW-CORT21-V1 Bedienungsanleitung

Omron

Omron CS1W-SCU21 Bedienungsanleitung

Omron

Omron CompoNetT E3NW-CRT Bedienungsanleitung

Omron

Omron GRT1 - 27-11-2006 Bedienungsanleitung

Omron

Omron V670 Series Bedienungsanleitung

Omron

Omron C200HW-COM01 Bedienungsanleitung

Omron

Omron ZS-CRT Bedienungsanleitung

Omron

Omron SMARTSLICE - 04-2008 Bedienungsanleitung

Omron

Omron Sysmac E3X-ECT Bedienungsanleitung

Omron

Omron DRT1-COM Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung