Omron E5ZN Series Bedienungsanleitung

Modular Temperature Controller E5ZN I-129

Temperature

Controller

Modular Temperature Controller

E5ZN

New DIN Track Mounting Temperature

Controller

• Two channels of temperature control available despite width of

only 22.5 mm.

• The Temperature Controller itself can be replaced without

changing terminal wiring.

• Use in combination with a compact Setting Display Unit to

reduce communications programming requirements.

• A wide variety of operation indicators (single-color LEDs)

enable easy operation monitoring.

• Power supply and communications wiring not required between

Units when mounted side-by-side.

Model Number Structure

■Model Number Legend

1. Control points

2: Two points

2. Control output

Q: Voltage (for driving SSR)

T: Transistor

C: Current

3. Auxiliary output

P: Transistor (sourcing)

N: Transistor (sinking)

4. Option

H: Heater burnout alarm

F: Transfer output

5. Communications

03: RS-485

6. Input type

TC: Thermocouple

P: Platinum resistance thermometer

7. CompoWay/F serial communications

-FLK: CompoWay/F serial communications

12 3 456 7

E5ZN- 2 @@@@@-FLK

I-130 Modular Temperature Controller E5ZN

Ordering Information

■List of Models

Note: 1. Terminal Units are required for wiring. Purchase separately.

2. When connecting the load of the controlled system, heat control output or cool control output can be allocated to the control output or auxiliary

output. When connecting a recording device or Digital Panel Meter, transfer output can be allocated to control output or auxiliary output 3 or 4 of

analog output models.

3. When using the heater burnout alarm, purchase a Current Transformer (CT) separately.

4. When using heating and cooling control functionality, the auxiliary output will be either heating control output or cooling control output.

5. Analog input and infrared temperature sensors (ES1A-A) can also be used with thermocouple models.

Note: 1. When using 2 or more E5ZNs mounted side-by-side, use the E5ZN-SCT18S-500 for the second and subsequent Units. When using

E5ZNs separately, be sure to use the E5ZN-SCT24S-500.

2. Two End Plates are provided with E5ZN-SCT24S-500 Terminal Units. When mounting to a DIN track, be sure to mount End Plates on

both sides.

Current Transformer (CT) (Order

Separately)

Terminal Cover

Note: The Terminal Cover comes with the Terminal Unit and does not

have to be purchased separately.

Setting Display Unit (Order Separately)

Note: Purchase sockets for wiring (shown on page 130) separately.

Sockets (for Setting Display Unit - Order Separately)

Note: Refer to the following manual for precautionary information and other information necessary to use the E5ZN: E5ZN Temperature Controller

Operation Manual (Cat. No. H113).

Name Power

supply No. of

control

points

Control

output Auxiliary

output Functions Communica-

tions func-

tions

Input type (See

note 5.) Model

Temperature

Controller(See

note 1.) 24 VDC 2

Voltage

output

(for SSRs)

Transistor

output: 2 pts

(sinking)

Heater

burnout alarm

(See note 3.) Heating or

heat/cool

control is

selectable

(See note 4.)

Event input: 1

point per Unit

RS-485

Thermocouple E5ZN-2QNH03TC-FLK

Platinum

resistance

thermometer E5ZN-2QNH03P-FLK

Transistor

output: 2 pts

(sourcing)

Thermocouple E5ZN-2QPH03TC-FLK

Platinum

resistance

thermometer E5ZN-2QPH03P-FLK

Transistor

output

Transistor

output: 2 pts

(sinking)

Thermocouple E5ZN-2TNH03TC-FLK

Platinum

resistance

thermometer E5ZN-2TNH03P-FLK

Transistor

output: 2 pts

(sourcing)

Thermocouple E5ZN-2TPH03TC-FLK

Platinum

resistance

thermometer E5ZN-2TPH03P-FLK

Analog

output

(current

output)

(See note 2.)

Transistor

output: 2 pts

(sinking)

Transfer out-

put (linear

voltage out-

put)

(See note 2.)

Thermocouple E5ZN-2CNF03TC-FLK

Platinum

resistance

thermometer E5ZN-2CNF03P-FLK

Transistor

output: 2 pts

(sourcing)

Thermocouple E5ZN-2CPF03TC-FLK

Platinum

resistance

thermometer E5ZN-2CPF03P-FLK

Name No. of terminals Functions Model

Terminal Unit

(Includes bus system with-

out backplane.)

24 Equipped with communications terminals for power supply, commu-

nications, and setting devices. E5ZN-SCT24S-500

18 (See note 1.) Not equipped with communications terminals for power supply,

communications, and setting devices. E5ZN-SCT18S-500

Model E54-CT1 E54-CT3

Diameter 5.8 dia. 12.0 dia.

Model E53-COV12 E53-COV13

Type For SCT24S-500 models For SCT18S-500 models

Name Power supply Model

Setting Display Unit

(See note.)

24 VDC E5ZN-SDL

Model P2CF-11 P2CF-11-E P3GA-11 Y92A-48G

Type Front-connecting socket Front-connecting socket

(with finger protection) Back-connecting socket Terminal cover for finger

protection

Modular Temperature Controller E5ZN I-131

Temperature

Controller

Specifications

■Ratings

Note: 1. ES1A models with a temperature range of 160×C to 260×C have been discontinued.

2. OMRON G32A-EA Cycle Controller Unit (load impedance 352 Ω) can be used.

■Input Range

Platinum Resistance Thermometer Models and Thermocouple Models

The applicable standards for the input types are as follows:

•K, J, T, E, N, R, S, B: JIS C1602-1995, IEC584-1

•L: Fe-CuNi, DIN 43710-1985

•U: Cu-CuNi, DIN 43710-1985

•JPt100: JIS C 1604-1989, JIS C 1606-1989

•Pt100: JIS C 1604-1997 IEC 751

Shaded parts indicate the settings at the time of purchase.

Note: ES1A models with a temperature range of 160×C to 260×C have been discontinued.

Power supply voltage 24 VDC

Allowable voltage range 85% to 110% of the rated power supply voltage

Power consumption Approx. 3 W

Sensor input

Thermocouple: K, J, T, E, L, U, N, R, S, B

Infrared temperature sensor (ES1A series): 10 to 70×C, 60 to 120×C, 115 to 165×C, 160 to 260×C (See note 1.)

Voltage input: 0 to 50 mV

Platinum resistance thermometer: Pt100, JPt100

Control output

Voltage output

(for driving SSR)

Output voltage: 12 VDC ±15% (PNP);

Maximum load current: 21 mA;

Equipped with short-circuit protection circuit

Transistor output

Maximum operational voltage: 30 VDC;

Maximum load current: 100 mA;

Residual voltage: 1.5 V max.;

Leakage current: 0.4 mA max.

Current output Current output range: 4 to 20/0 to 20 mA DC;

Load: 350 Ω max. (See note 2.)

Auxiliary output

Transistor output

Sourcing Maximum operating voltage: 30 VDC;

Maximum load current: 50 mA;

Residual voltage: 1.5 V max.;

Leakage current: 0.4 mA max.

Sinking

Linear voltage output Voltage output range: 1 to 5/0 to 5 VDC;

Load: 10 kΩ min.

Event input

Contact output ON: 1 kΩmax., OFF: 100 kΩmin.

Discharge current: Approx. 7 mA

Non-contact output ON: Residual voltage: 1.5 V max., OFF: Leakage current: 0.1 mA max.

Discharge current: Approx. 7 mA

Number of input and control points Input points: 2, Control points: 2

Setting method Via communications or using the Setting Display Unit (E5ZN-SDL)

Control method 2-PID or ON/OFF control

Other functions Heater burnout detection function, transfer output function

Multi-SP and RUN/STOP switching using event input

Ambient operating

temperature −10 to 55×C (with no icing or condensation)

For 3 years of assured use: −10 to 50×C

Ambient operating humidity 25% to 85%

Storage temperature −25 to 65×C (with no icing or condensation)

1800

1700

1600

1500

1400

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

−100

−200

01234 0 1 2 3 4 17 5 6 7 18 8 9 10 11 12 13 14 15 16

−200 −200

−199.9 −199.9

500.0 500.0

0.0 0.0

100.0 100.0

−20.0 −100 −20.0

−200

−199.9 −199.9

−100

−200 −200

100.0 0000

260

165

120

400400

850

600

400.0400.0400.0

500.0

850850

1300 1300

1700 1700

1800

Platinum resistance

thermometer models

Platinum resistance

thermometer

Input type

Name

Temperature range (°C)

Setting

number

KJTELUNRSB

Pt100 JPt100

Thermocouple

Thermocouple models

Infrared temperature

sensor (ES1A) Analog input

0 to 50 mV

−

1999 to

9999 or

−

199.9 to

999.9

by scaling

10 to

70°C

60 to

120°C

115 to

165°C

160 to

260°C

I-132 Modular Temperature Controller E5ZN

■Characteristics

Note: 1. The indication accuracy for T and N thermocouples at −100×C, and for U and L thermocouples is ±2×C ±1 digit max. There is no speci-

fication for the indication accuracy for the B thermocouple used at 400×C max. The indication accuracy for R and S thermocouples at

200×C max. is ±3×C ±1 digit max.

2. The transfer output accuracy for 0 to 4 mA when 0 to 20 mA DC is selected is ±0.5% FS +0.7 mA. The transfer output accuracy for 0 to

1 V when 0 to 5 VDC is selected is ±0.5% FS +0.175 V.

3. “EU” stands for “Engineering Unit.”

4. In order to satisfy the EN61326 Class A standard for conducted emissions, install a noise filter (Densei-Lambda MXB-1206-33 or equiv-

alent) in a DC power line as close to the E5ZN as possible.

Indication

accuracy

Thermocouple: (Indicated value ±0.5% or ±1×C, whichever is greater) ±1 digit max. (See note 1.)

Platinum resistance thermometer: (Indicated value ±0.5% or ±1×C, whichever is greater) ±1 digit max. (See

note 1.)

Analog input: ±0.5% or ±1 digit max.

CT input: ±5% FS ±1 digit max.

Transfer output Accuracy: ±0.5% FS (See note 2.)

Hysteresis 0.1 to 999.9 EU (in units of 0.1 EU)

(See note 3.)

Proportional band (P) 0.1 to 999.9 EU (in units of 0.1 EU)

(See note 3.)

Integral time (I) 0 to 3,999 s (in units of 1 s)

Derivative time (D) 0 to 3,999 s (in units of 1 s)

Control period 1 to 99 s (in units of 1 s)

Manual reset value 0.0 to 100.0% (in units of 0.1%)

Alarm setting range −1,999 to 9,999 (Position of decimal point depends on input type.)

Sampling period 500 ms

Insulation resistance 20 MWmin. (at 500 VDC)

Dielectric strength 600 VAC for 1 minute at 50 or 60 Hz (between unlike terminals of charged parts)

Vibration resistance 10 to 55 Hz, 10 m/s2for 2 hrs each in X, Y, and Z directions

Shock resistance 150 m/s2max., 3 times each in ±X, ±Y, and ±Z directions

Enclosure rating Temperature Controller: IP00

Terminal Unit: IP00

Memory protection EEPROM (non-volatile memory) (Number of write operations: 100,000)

Weight Temperature Controller: Approx. 90 g

Terminal Unit (18): Approx. 80 g

Terminal Unit (24): Approx. 100 g

Approved standards

(See note 4.)

UL File No.: E200593

CSA File No.: 203889-1140084

CE EMS: ESD EN61326, EN61000-4-2 (4 kV/contact, 8 kV/air)

REM field EN61326, EN61000-4-3 (10 V/m)

Fast transient EN61326, EN61000-4-4 (2 kV/DC power, 1 kV/I/O)

Surge immunity EN61326, EN61000-4-5 (line to ground: 2 kV/DC power

1 kV/I/O

line to line: 1 kV/DC power)

Conducted RF EN61326, EN61000-4-6 (10 V)

EMI: Radiated EN61326 Class A

Modular Temperature Controller E5ZN I-133

Temperature

Controller

■Communications

(Host Communications)

Note: The baud rate, data bit length, stop bit length, and vertical par-

ity can all be set independently as host communications set-

tings.

■Setting Display Unit (Order

Separately)

Ratings and Characteristics

■Current Transformer (CT)

Ratings (Order Separately)

■Heater Burnout Alarm

Characteristics

Note: 1. Use the K2CU-F@@A-@GS (with GATE input terminal) for

burnout detection of 3-phase heaters.

2. If the heater burnout alarm setting is set to 0.0 A, the alarm

is always OFF, and if it is set to 50.0 A the alarm is always

ON.

3. If the ON time for control output is less than 190 ms, heater

burnout detection and heater current measurement will not

be performed.

Transmission line

connection method RS-485 multipoint

Communications

method RS-485 (2-wire, half-duplex)

Synchronization

method Start-stop synchronization

Baud rate 4,800, 9,600, 19,200, or 38,400 bps

Transmission code ASCII

Data bit length

(See note.) 7 or 8 bits

Stop bit length (See

note.) 1 or 2 bits

Error detection Vertical parity (none, even, odd)

BCC (block check character)

Flow control None

Interface RS-485

Retry function None

Number of Units that

can be connected in

parallel 16 Units max. (32 channels)

Power supply voltage 24 VDC

Allowable voltage

range 85% to 110% of the rated power supply

voltage

Power consumption Approx. 1 W

Display method 7-segment digital display and single-color

display

Ambient operating

temperature

−10 to 55×C (with no icing or condensa-

tion)

For 3 years of assured use: −10 to 50×C

Ambient operating hu-

midity 25% to 85%

Storage temperature −25 to 65×C (with no icing or condensa-

tion)

Communications

method RS-485 (half-duplex)

Communications for-

mat Fixed

Insulation resistance 20 MWmin. (at 500 VDC)

Dielectric strength 1,500 VAC for 1 minute at 50 or 60 Hz (be-

tween unlike terminals of charged parts)

Vibration resistance 10 to 55 Hz, 20 m/s2for 2 hrs each in X, Y,

and Z directions

Shock resistance 300 m/s2max., 3 times each in ±X, ±Y, and

±Z directions

Enclosure ratings Front panel: IP50

Rear case: IP20

Terminal case: IP00

Memory protection EEPROM (non-volatile memory) (Number

of writes: 100,000)

Weight Approx. 100 g

Mounting bracket: Approx. 10 g

Dielectric strength 1,000 VAC (1 minute)

Vibration resistance 50 Hz, 98 m/s2

Weight E54-CT1: Approx. 11.5 g

E54-CT3: Approx. 50 g

Accessories

(E54-CT3 only) Armature (2)

Plug (2)

Maximum heater

current Single-phase, 50 A AC (See note 1.)

Input current

readout accuracy ±5% FS ±1 digit max.

Heater burnout

alarm setting range 0.0 to 50.0 A (in units of 0.1 A)

(See note 2.)

Minimum detection ON

time 190 ms (See note 3.)

I-134 Modular Temperature Controller E5ZN

Nomenclature

E5ZN-2

E5ZN-SDL

The following diagram shows the names and functions of the E5ZN-SDL parts for when it is connected to the E5ZN-2@@@@@@@.

Operation Indicators

POWER

Lights when power is turned ON.

ERROR

Lights when a fatal error (e.g., memory

error or sensor error) occurs.

SD/RD (Communications Operation)

Flashes during communications with the host.

OUT1 (Control Output 1)

Lights when the control output 1 is ON.

OUT2 (Control Output 2)

Lights when the control output 2 is ON.

SUB1 (Auxiliary Output 1)

Lights when the auxiliary output 1 is ON.

SUB2 (Auxiliary Output 2)

Lights when the auxiliary output 2 is ON.

POWER

ERROR

SD/RD

OUT1

OUT2

SUB1

SUB2

Unit Number Setting

Setting range of 0 to F allows up

to 16 Units to be set.

Baud Rate

No. 1 Display

Displays the PV or the type of

setting data.

No. 2 Display

Displays the target value, the

control variable, or the set value

for setting data (setting contents).

Up Key

Each time this key is pressed, the

value displayed in No. 2

Display increases. If it is held

down, the rate of increase

becomes faster.

It can also be used to move to the

next setting item.

Down Key

Each time this key is pressed, the

value displayed in No. 2

Display decreases. If it is held

down, the rate of decrease

becomes faster.

It can also be used to return to the

previous setting item.

Channel Key

Press this key to change the

channel number.

Copy Key

Press this key to read all the

settings from the Temperature

Controller to the Setting Display

Unit, or to write from the Setting

Display Unit to the Temperature

Controller.

UNIT Key

Press to switch the unit number.

Level Key and Mode Key

Press together to switch to protect mode.

Mode Key

Press this key to switch setting

data within the setting level.

Level Key

Press this key to switch setting

levels.

Unit/Channel Indicator

Indicates the unit number and

the channel number.

• SUB3 (Auxiliary Output 3)

Pulse output models: Always not lit.

Analog output models: Not lit when the

auxiliary output drops to 0% or lower.

Lit when the auxiliary output is above 0%.

• CMW (Communications Write Control)

Lights when communications write is permitted

and remains unlit when it is prohibited.

• STOP

Lights when operation stops. Lights for an

event or when RUN/STOP is set to STOP

during control. Remains unlit at other times.

• SUB1, SUB2 (Auxiliary Output 1, Auxiliary

Output 2)

Light when the auxiliary output 1 or the

auxiliary output 2 functions are ON.

• OUT1, OUT2 (Control Output 1, Control

Output 2)

Light when the control output 1 or the control

output 2 functions are ON.

• These indicators indicate the terminal

operations for the E5ZN-2@@@@@@@.

Operation Indicators Temperature Unit

Displayed when the display unit for setting

data is temperature. The display is

determined by the setting for temperature unit,

with either “°C” or “°F” displayed accordingly.

• SUB4 (Auxiliary Output 4)

Pulse output models: Always not lit.

Analog output models: Not lit when the

auxiliary output drops to 0% or lower.

Lit when the auxiliary output is above 0%.

Modular Temperature Controller E5ZN I-135

Temperature

Controller

Dimensions

Note: All units are in millimeters unless otherwise indicated.

E5ZN-2@@@03@-FLK Connected to E5ZN-SCT24S-500 E5ZN-2@@@03@-FLK Connected to E5ZN-SCT18S-500

Note: Refer to the following manual for precautionary information and other information necessary to use the E5ZN: E5ZN Modular Temperature

Controller User’s Manual (Cat. No. H113).

End Plate

PFP-M

Note: End Plates are provided with the E5ZN-SCT24-500. Be sure to

mount End Plates at both ends of Unit blocks.

Spacer

PFP-S

Current Transformer (Order Separately)

Mounting Track (for DIN Track Mounting - Order Separately)

PFP-100N

PFP-50N

When only using one Unit,

purchase the E5ZN-2@@@03@-

FLK and the E5ZN-SCT24S-500

together. Also, when using

horizontal side-by-side mounting,

purchase the first Unit together with

the E5ZN-SCT24S-500.

112

72.8 130

22.3

30 4.7

When mounting Units side-by-

side, purchase the E5ZN-

2@@@03@-FLK together with

the E5ZN-SCT18S-500 for the

second and subsequent Units.

22.5

5.2 4.7

130

72.8

112

11.5

6.2

1.8

1.3

4.8

35.5 35.3

1.8

Eight, M4

pan-head

screws

M4 spring washer

44.3 34.8

16.5

40 ×40

E54-CT1 E54-CT3

5.8 dia.

2.36 dia.

12 dia.

Two, 3.5 dia. Two, M3 (Depth: 4)

E54-CT3 Accessories

Armature

Approx. 3 dia. Approx.

6 dia.

Plug

Connection Example

Plug Armature

Lead wire

25 3

10.5

7.5

2.8

(22)

15 (5)*

7.3±0.15

35±0.3 27±0.1

* Indicates dimensions for the PFP-50N.

4.5

1,000 (500)*

15 25 25 25 25

10 10

I-136 Modular Temperature Controller E5ZN

Setting Display Unit

E5ZN-SDL

E5ZN-SDL Wiring Sockets

Front-connecting Sockets

Back-connecting Sockets

Terminal Cover

48 × 48 6

(84)

63.7 14.2

44.8 ×44.8

+0.6

45+0.6

60 min.

(48 ×No. of Units – 2.5)

+1.0

Individual Mounting Side-by-side Mounting

Panel Cutout Dimensions

• Vertical side-by-side mounting is not

possible.

(Allow sufficient space above and below.)

• The mounting panel thickness is 1 to 5 mm.

• When mounting several Units, make sure

that the ambient tem-perature

specifications are not exceeded.

35.4

7.8 4.5

35.4

4.5

7.8

1.2

40 ±0.2

P2F-11 (Standard Model)

P2F-11-E (with Finger Protection)

Two, 4.5-dia. holes

Eleven, M3.5 ×7.5 Sems screws

Two, 4.5-dia. holes

Eleven, M3.5 ×7.5 set screws

31.2 max.

70 max.

Terminal Arrangement/

Internal Connections

Mounting Hole

Cutout Dimensions

(TOP VIEW)

Two, M4 or 4.5 dia.

Note: DIN track mounting

is also possible.

31.2 max.

50 max.

45 4.5 16.3

25.6

6.2

8.7

473

P3GA-11 (Standard Model)

Terminal Arrangement/

Internal Connections

(BOTTOM VIEW)

27 dia.

Note: Use in combination with a Terminal Cover (Y92A-48G)

for finger protection.

16.5 24.6 27.6

47.4

48 × 48

47.7 ×

47.7

Y92A-48G

Twelve, 6.4 dia.

Modular Temperature Controller E5ZN I-137

Temperature

Controller

Installation

■Connection Diagrams

•Voltage output (control output) is not electrically isolated from internal circuitry. Therefore, when using grounded thermocouples, do not ground

control output terminals. (Doing so may result in temperature measurement errors due to unwanted current paths.)

•There is basic insulation between the power supply inputs and outputs for this product. If reinforced insulation is required, connect the input and

output terminals to equipment without any exposed charge-carrying parts, or to equipment with basic insulation sufficient for the maximum oper-

ating voltage of the power supply and the inputs and outputs.

Using with the E5ZN-SCT24S-500

Using with the E5ZN-SCT18S-500

E5ZN-SDL

Note: Purchase either a P2CF-11 or a P3GA-11 Socket separately. (Refer to page 136.)

24-VDC input

power supply*

E5ZN-SDL

RS-485

host

Wiring for terminals 1 to 18 is the same

as for the E5ZN-SCT18-500. See below.

*Power supply: recommended power

supply; eg. OMRON S8VS

−

13 71

−

CT1

CT2

−

1-5 VDC/

0-5 VDC

1-5 VDC/

0-5 VDC

4-20 mA DC/

0-20 mA DC

4-20 mA DC/

0-20 mA DC

12 VDC

21 mA

12 VDC

21 mA OUT2

OUT2

OUT1

Analog input

ch1 ch1ch1 ch2ch2ch2

ch1

OUT1

ch2

SUB1

SUB2

COM

SUB1

SUB2

COM

Event input

E5ZN-SCT18S-500

OUT2

ch2ch1

OUT1

ch1

ch2

SUB3

SUB4

PNP (sourcing) type

E5ZN-2@P@03@-FLK

Voltage-output type

E5ZN-2Q@H03@-FLK

Transistor-output type

E5ZN-2T@H03@-FLK

NPN (sinking) type

E5ZN-2@N@03@-FLK

Analog-output type

(linear-voltage-output)

E5ZN-2C@F03@-FLK

Contact

input

Non-

contact

input

Thermocouple/infrared

temperature sensor

Analog-output type

E5ZN-2C@F03@-FLK

Voltage-output type

E5ZN-2Q@H03@-FLK Transistor-output type

E5ZN-2T@H03@-FLK

When the E5ZN-SCT24S-500 is used Do not use.

Host side

(RS-485)

Do not use.

24 VDC input power supply

Recommended power

supply; eg. Omron S8VS.

Note: 1. Terminals 4 and 9, 7 and 11,

and 8 and 10 are connected

internally at the E5ZN-SDL

side.

2. Do not connect anything to

terminals 1, 2, 5, and 6.

I-138 Modular Temperature Controller E5ZN

Operation

alh1

0.2

°c

alh2

0.2

°c

hbu

hbl

off

mspu

off

eU-m

a1lt

off

a2lt

off

a3lt

off

inf

0.0

pUad

off

isdp

off

init

off

none

rest

al1n

n-o

al2n

n-o

alfa

0.65

ol-h

105.0

ol-l

- 5.0

sero

off

hbh

0.1

ot-2

amoU

sedu

istp

cjc

sprt

al3n

n-o

alh3

0.2

°c

sub4

out2

sub1

sub2

sub3

tr1h

1300

cont

tr3h

1300

tr1l

-200

tr2h

1300

tr2l

-200

tr3l

-200

tr4h

1300

ot-1

tr4l

-200

in-l

sl-h

1300

°c

sl-l

- 200

°c

cntl

onof

alt1

alt2

in-t

in-h

100

d-u

alt3

c-cp

oreU

or-r

out1

len

sbit

prty

eUen

sdwt

Multi-SP uses

SP ramp set

value

Additional PV display

Operation after

power ON

OUT1 transfer

output upper limit

OUT1 transfer

output lower limit

ch2: ch1:

in-h

100

in-h

100

in-h

100

E5ZN-SDL Setting Data

The setting data that can be set from the E5ZN-SDL Setting Display

Unit is shown below. Depending on the protection settings and

other factors, some settings may not be displayed. A password is

required to move to the advanced function setting level.

The display below indicates that

there is setting data for ch1 or ch2.

Press the Button to switch between

the screens for ch1 and ch2.

This symbol indicates setting data that is displayed only for models with pulse output.

("Models with pulse output" is used here to indicate models with voltage output or transistor output.)

This symbol indicates setting data that is displayed only for models with analog output.

Communications

setting level

@Key

1 s max.

Communications

data length

Communications

stop bit

Communications

parity

Communications

response wait time

Advanced function

setting level Move to

the

advanced

function

setting

level by

entering

the

password

"−169".

Parameter

initialize

Number of

multi-SP

uses

Event input

allocation

Standby sequence

reset

Alarm 1 open

in alarm

Alarm 1

hysteresis

Alarm 2 open

in alarm

Alarm 2

hysteresis

Alarm 3 open

in alarm

Alarm 3

hysteresis

HBA ON/OFF

Heater burnout latch

Heater burnout

hysteresis

Voltage output type

Sensor error

indicator used

Move to advanced

function setting level

Top of initial setting level

2-PID parameter

MV upper limit

MV lower limit

Input digital filter

Additional

temperature input

shift value display

Temperature

input shift type

Alarm 1 latch

Alarm 2 latch

Alarm 3 latch

Input error output

Cold junction

compensating

method

Top of advanced function setting level

@Key 1 s min.

Control output 2

allocation

Auxiliary output 1

allocation

Auxiliary output 2

allocation

Auxiliary output 3

allocation

Auxiliary output 4

allocation

OUT2 transfer

output upper limit

OUT2 transfer

output lower limit

SUB3 transfer

output upper limit

SUB3 transfer

output lower limit

SUB4 transfer

output upper limit

SUB4 transfer

output lower limit

Current output type

Initial setting value

Input type

Scaling upper limit

Scaling lower limit

Decimal point

Temperature unit

PID ON/OFF

Alarm 1 type

Alarm 2 type

Alarm 3 type

Control output 1

allocation

SP upper limit

SP lower limit

Control period

(heat)

Control period

(cool)

Direct/reverse

operation

@Key

Andere Handbücher für E5ZN Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Omron Temperaturregler Handbücher

Omron

Omron E5CZ Bedienungsanleitung

Omron

Omron E5CN-H Bedienungsanleitung

Omron

Omron E5C series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

Omron

Omron E5AN-H Bedienungsanleitung

Omron

Omron E5AZ Bedienungsanleitung

Omron

Omron E5CC Gebrauchs- und Pflegehandbuch

Omron

Omron E5CN Bedienungsanleitung

Omron

Omron E5CC Bedienungsanleitung

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

Omron

Omron EJ1 EtherCAT Bedienungsanleitung

Omron

Omron E5CC-800 Bedienungsanleitung

Omron

Omron E5CN-HT Bedienungsanleitung

Omron

Omron E5AX-BA Series Bedienungsanleitung

Omron

Omron EJ1N-TC4 Bedienungsanleitung

Omron

Omron E5*N Series Installationsanleitung

Omron

Omron E5GN Bedienungsanleitung

Omron

Omron E5C series Bedienungsanleitung

Omron

Omron E5C2 Bedienungsanleitung

Omron

Omron E5ZN-DRT Bedienungsanleitung

Omron

Omron E5C-T Series Gebrauchs- und Pflegehandbuch

Omron

Omron E5EWL Bedienungsanleitung

Omron

Omron E5CS-U Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema

Opt Lasers

Opt Lasers TEC-8A-24V-PID-HC Bedienungsanleitung

Vaillant

Vaillant VR 92/3 Bedienungsanleitung