ONAGOfly1's propellers can be
dismantled.*
When assembling, the propellers
should be installed in corresponding
positions. The propellers engraved
with the numbers. The letters
marked on propellers (A, B, C, D)
shall be respectively corresponding
to the letters on bottom machine
arms during assembly. The method of installing is seen as the figure (1). The
propellers must be installed in the right position regarding the safety. As seen in
figure (1). Otherwise Onagofly1 flight may be affected. Orange propellers shall
A
C
D
B
AC
DB
×
√
Notes:
There're two at the bottom of the GPS antenna coverage. So does that on
PCB board. These touch pots must be connected when installing. The Micro USB
port on the aircraft is only for maintenance. Please do not connnect it for charging.
contacts
Technical specification:
Aircraft
100*100*45mm
Weight: 135g (±2g)
Max Ascent Speed: 5m/s
Max Descent Speed: 3m/s
Max Speed: 15Km/h
Max Service Ceiling: 30m
Max Flight Time: Approximately 12 minutes
Features
Auto-takeoff
Auto-landing
Follow-me
Tilt mode
Battery
800mAh LiPo 2S
Memory card up to 64GB (exFAT C10 and above)
Battery power: 5.9Wh
Operating temperature: -10℃ to 40℃
Aircraft dimension (L*W*H):
Controlled by mobile device
Wifi working frequency: 2.4GHz
Max Communication Distance (open area):
30-50m (depending on Wifi signal
environment)
Receiving sensitivity of signals: -50dBm
Camera
Photos: 15 megapixels
Video: 1080P@30fps
Other accessories
3-inch propellers
Something you need to know before
using your ONAGOfly1:
be installed on the motor on the same side as the camera lens. After the
installation, please place the aircraft on open ground flatly, taking off from the
uneven ground may affect its attitude. (The camera's front should be the same
as the pilot's. Before taking off please make sure the camera's front is the same
as pilot's) *When disassemble the propellers, please fix the motor with one hand
and rotate the propellers counterclockwise upside slowly.
If video recording or taking photo is necessary, please make sure that Micro SD
card (the maximum memory of Micro SD card is 64GB (exFAT), Class10 and
above) has been correctly inserted. Besides, please format the Micro SD card into
FAT32 or exFAT (for 64GB SD card) format. Otherwise the aircraft may not be
turned on.
Maintain control at all times: even when using ONAGOfly1 autopilot functions
such as Auto-Takeoff, Auto-landing, always keep your hands on the Mobile
Device and maintain control of your aircraft when it is in flight.
Auto-landing due to the low battery, please do not fly it again manually, which
can result in damage to the battery.
Each time when you finish use with ONAGOfly1, please make sure to shut down
the power by pressing the power button.
Environmental Considerations
Do not fly in severe weather conditions. This include high winds (speed of 8-16km/h or
more), snow rain and fog.
Only fly in open areas. Tall buildings and steel structures may affect the accuracy
of the on-board compass and GPS signal.
Avoid obstacles, crowds, high-voltage power lines, trees and bodies of water.
Minimize electromagnetic interference by avoiding areas with high levels of
electromagnetism, including mobile phone base stations, radio transmission towers,
or Wi-Fi hotspots.
Aircraft and battery are subject to environment factors such as air density and
temperature. Be very careful when flying 6km (19,600ft) or more above sea level,
as battery and aircraft performance may not be at peak efficiency.
The GPS positioning mode can not be used for flight in the Antarctic/Arctic
Circle.
32
● Figure (1)
▲
▲
▲
▲
▲
Make sure to check whether the propellers are intact and fixed before flight, and
do not take off if any propellers are damaged or loose.
Please check the battery capacity before taking off and check whether the Micro
SD card is correct installed. The right way to install the Micro SD card: The side
with metal contacts on should be upside when inserting into the slot.
When the GPS is wink (As seen in figure (11)), Onagofly1 could fly stable in the
air but could not hold its position.
The initial password and the wifi network name would be modified in the setting
menu.(As seen in figure (9)). It vary when you restart.
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
