One Remote BEE2 Bedienungsanleitung
User guide, English
OneRemote beeLINK2 controller operates:
Panasonic BlueRay players
DMP-BD30, BD80 ... and more
User guide type 34016101 BEE2
2
Beo4/ Beo5 Translation table.
Daily operations Playback operations
OO OK/ enter
W*1 Functions
R*1 Display
Q*1 Top Menu
E*1 Return
m Menu
e Exit
Oe Option
*1
As the direct function of the coloured function
buttons has been assigned to other functions,
these have to be preceded with a oto
retrieve the actual coloured function.
oQ Green function
oW Yellow function
oE Red function
oRBlue function
o Play press 1 sec.
q Stop
oq Pause
oAS Search
oDD Next/ prev
Other operations
o1 Status
o2 Pop Up Menu
o4 Remaster
o6 PIP
o7 Audio
o8 Secondary audio
o9 Open
Special/ alternative operations
o0 Play
o5 Setup
3
Congratulations
The beeLINK2 controller from www.oneremote.dk can fully
operate your device using your Bang & Olufsen remote con-
trol terminal, via a beeLINK system bus.
Beo4 or Beo5 remote controls can be used. Beolink 1000 can
be used with reduced functionality. This guide explains how.
This beeLINK2 controller is ready for use, plug & play. See
the opposite page regarding daily operation.
Some operations can be altered, to improve interaction with
other controllers or to your convenience. Refer to the installa-
tion section further on, if changes are needed.
4
List of Contents
Beo4/ Beo5 Translation table ........................ page 2
beeLINK basics .............................................. page 5
beeLINK2 installation .................................... page 6
beeLINK2 connections .................................. page 8
Operation with OneRemote - OneRemote environment page 9
Beolink 1000 .................................................. page 10
Option programming ...................................... page 11
Programme zapping option ............................ page 11
Menu button option ........................................ page 11
Power off option ............................................ page 12
beeLINK2 active option ................................. page 13
5
beeLINK basics
The IR data emitted from a Bang & Olufsen remote control, is captured with a IR-
receiver. If there is already one IR-receiver in the room, this can also be used to feed
the BeeLINK bus. Normally there is no need for two IR receivers in the same room.
Data received by the IR-receiver is fed to a OneRemote Link Amplifier with built-in
power supply and 5 outputs for beeLINK devices.
If there is more than 5 beeLINK devices in the setup, splitters can be added.
The BeeLINK bus distributes the IR-data, received with the attached IR-receiver from
a Beolink 1000, Beo4 or Beo5 to any number of beeLINK controllers. It also supplies
the attached controllers with power.
The cable used between the link amplifier and the controllers is simple CAT5 type ca-
ble with RJ45 plugs. This type of cable is inexpensive and a standard cable that any
installer are familiar with. Also it is well suited for data transmission. Finally many
modern house installations use the same connectors, making installation even easier.
Note !
A BeeLINK bus must ONLY be connected to other beeLINK components.
If connected to LAN or other systems, there is a great risk to damage these systems.
6
The BeeLINK bus is a parallel bus type. Passive splitters therefore can be used, to
make a network of any shape. If many controllers or very long cables are used, it might
be necessary to add more power supplies.
Using this parallel structure each beeLINK controller receives the IR-data simultane-
ously. Every controller has its own microcomputer, living its own life.
Although some of the controllers can ‘talk’ to each other, most controllers operate fully
on their own.
beeLINK2 installation
The beeLINK2 controller gets its power supply and control data, via the CAT5 cable
from a beeLINK amplifier. The beeBus.
Once connected to the beeBUS the beeLINK2 controller only needs an IR-emitter to
operate the device it has been designed for. The IR-emitter emits the same IR data as
the device’s own remote control.
Emitted IR data is in fact pure light at a frequency just out of the spectrum that the human eye is able to see.
It emits short flashes of light, a bit like when sending Morse codes using a flashlight.
The emitter must be stuck on the device, nearby the De-
vices IR-receiver. It must be placed so the IR receiver in
the device is able to see the emitted light from the IR-
emitter.
The beeLINK2 controller can be placed by the device or
in another room. IR emitters are available in lengths of 1,
5 and 10 meters. Additional extension cords can be used.
An IR-emitter can be extended to more than 50 meters.
The IR-emitter can be placed inside the device, if you want to avoid having it on the
outside, as long as the IR-receiver is able to see the light from the emitter. This requires
that the device is opened and the emitter is placed inside.
7
A beeBUS CAT5 cable may exceed more than 75 meters without additional amplifiers.
Some beeLINK2 controllers requires not only a IR-emitter, to operate a device. If the
device is not able to power on and off via separate commands, the beeLINK controller
needs to measure the power status of the device.
This is done using special IR-emitters that either measures the status signal on a TV-
scart output or the presence of a video signal.
OneRemote 81108180 IR-emitter cable.
Measures the DC-status on a Scart TV-output.
OneRemote 31108182 IR-emitter cable.
Measures the presence of a video output signal.
8
beeLINK2 connections.
The IR/ sense socket is output for the IR-emitter that sends IR to the device to be oper-
ated. In some cases this socket is also used for sensing purposes. Sometimes the Bee-
LINK2 controller needs to know if the device is powered up or not.
In some cases this socket is used for other serial communications like RS-232 instead
of IR control.
Prog switch is a push button that must be activated to initiate a programming se-
quence, as described in the option programming chapters.
Do not use socket is for firmware updating of the controller, and connection to special
adapters. If used for anything else, the controller will be damaged.
LED indicates different operating states:
Red-green flash: No data has been received since power has been applied
Red flash: The controller is in option programming mode.
Red: The controller is active.
Green: The controller is inactive.
Short off: When the controller sends data, the LED turns off 1 sec.
9
Operating with OneRemote - OneRemote environment.
To be able to operate the device optimal with the Beo4 the user has to be familiar with
operations with the original remote control as described in the device’s user manual.
The beo4 remote control is not equipped with as many keys as most other brands are
using. We have designed a ‘layout’ that works logically, even when shifting between
different OneRemote operated devices. To get a common layout for many devices, we
therefore needed to redefine a few of the beo4 buttons to other functions:
Coloured function buttons.
To make room for easy access to more important functions, we have moved the col-
oured buttons, to a lower layer. To send a ‘color’ command from the device’s original
RCU, a Omust be pressed before the coloured button.
This way we are able to assign other functions to the coloured buttons in direct mode.
In a OneRemote environment the coloured buttons are assigned to these operations:
Programme stepping, up/ down manoeuvring in menus.
Most set top boxes or TV’s has 4 arrow buttons for moving up, down, left and right in
on screen menus. In addition they have separate programme stepping buttons for zap-
ping through programmes. B&O remote controls does not have separate buttons for
programme zapping. We therefore have chosen the blue and the yellow buttons to func-
tion as programme stepping buttons, in direct mode. The four up, down, left and right
buttons have been assigned for manoeuvring in on screen menus, in our basic setup. It
is possible to use the up and down arrow for programme stepping, refer to the option
section, page 6.
Go or Record shifted operation.
Some of the buttons has 2 or three functions. To get to these they have to be preceded
with Oor r. The buttons that has been assigned secondary functions on this
controller can be seen in the operating table on page 2.
QGuide, EPG or similar.
EBack, Backup, Return or similar.
W
R
Programme zapping. P+/ P- ,
Channel up/ down or CH+/ CH-.
10
Beolink 1000 and Beo4/ Beo5.
Beolink 1000 and other early Bang & Olufsen remote controls are not equipped with
the coloured function buttons that have been added to Beo4 and Beo5. The lack of
these buttons makes it difficult to make a good layout, transparent for controlling dif-
ferent devices. Some operations therefore might be less logical or in some cases not
available, when using older remote controls in a beeLINK setup.
Some buttons on the Beolink 1000 remote controls, do actually send the same com-
mands as differently named buttons on a Beo4/ Beo5. Other buttons simply has been
renamed, but still sends the same commands.
Beolink 1000 Compares to Beo4/ Beo5
------------------- --------------------------------
hZ Q
hX W
hC R
hV E
o P
vT
hvVTAPE2 /VMEM2 /DVD2
sf
hs d/ CDV
ht a
y b
hyAMEM2
For compatibility with older remote controls, a typical OneRemote layout uses the fol-
lowing buttons:
Beolink 1000 Typical BeeLINK use
---------------- -----------------------------------------
gBack, Backup e.t.c.
pg EPG, Guide e.t.c.
xEXIT.
p5 Menu.
p9 Manual power.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere One Remote Universalfernbedienung Handbücher
