Optex InSight INS-QXI-ST Bedienungsanleitung
59-3063-1 2212-27
EN
INS-QXI-ST
INS-QXI-ST
INSTALLATION INSTRUCTIONS
1
2
3
4
5
- Manufacture's statement
- Parts identification
- Accessories
- Specifications
- Dimensions
- Detection area
- LED indicator
- Compliance
- How to reset to the factory default
Before installation
Others
<< Contents >>
Page
2
3
5
6
11
12
Step
Enabled
Disabled
Installation
IP address settings
Device registration to CHeKT portal
DHCP
Camera angle and PIR area settings
Checking
VISUAL VERIFICATION PIR CAMERA
series
1
1-1. Remove the mounting plate
1-2. Install the mounting plate using 2 screws
1-3. Connect cables to the device
1-4. Secure the main body
4-1. Horizontal adjustment
4-2. Vertical adjustment
4-3. PIR/VCA settings
4-4. PIR area masking
4-5. Switch settings
4-6. Put on the back cover
InSIght Camera manual
CHeKT support
Refer to the InSight Camera manual for details on
IP address settings.
InSIght Camera manual
https://navi.optex.net/manual/50426/en/?type=cameramanual
If you do not have a CHeKT account, request a dealer account
by visiting the CHeCK dealer site, before Step 3.
CHeKT dealer
www.chekt.com/registration
Refer to the CHeCK support site for more details.
CHeKT support
https://support.chekt.com
5-1. Walk test
5-2. System check
- Manufacture's statement
Failure to follow the instructions provided
with this indication and improper handling
may cause death or serious injury.
Failure to follow the instructions provided
with this indication and improper handling
may cause injury and/or property damage.
Check mark indicates recommendation.
Nix sign indicates prohibition.
Special attention is required to the section
of this symbol.
Symbol Meaning Symbol Meaning
Warning
Caution
NOTE
Warning Caution
Tilt
Before installation
Mounting height
2.2 m (7’ 3” ) to 2.7 m (8’ 11” )
Destroy
Disassemble
modify
Intentional watering
2
- Parts identification - Accessories
4 x 20 mm
Mounting screws T20 Torx wrench
Waterproof cap
for LAN connection
PIR area masking strips
PIR detector
Bracket angle adjusting screw
PIR cover
Camera unit Camera angle adjusting screw
Back cover
Mounting plate
Mounting on
an unstable
wall
1Installation
Step
1-1. Remove the mounting plate
12 3
3
1-2. Install the mounting plate using 2 screws
Hook the fall prevention wire.
To pass cables through the wall, drill a 25 mm (1") or larger hole in the wall.
Use a single gang box for exposed wiring.
NOTE
Caution
12
Caution Do not pinch the cable when restoring the PIR detector.
1
Installation
Step
Tamper
Alarm
Power
Caution
1-3. Connect cables to the device.
PoE LAN cable
DC power cable
12 V DC power for camera and PIR
8-pin I/O cable
+- SP N/A COM AL TP TP
Pink
Orange
Yellow
Brown
Green
Purple
Black
Red
Do not connect to the N/A terminal.
Waterproof cap
for LAN connection
It can be also used as a
back up for POE
Only the connector can be fixed
inside the body with double-sided
tape. The LAN connector must be
stored in the wall.
NOTE
1
2
3
4
How to connect the LAN cable with the waterproof cap
1-4. Secure the main body
4
2IP address settings
Step
3Device registration to CHeKT portal
Step
The default network type of InSight is dynamic.
If you have a DHCP server, it will automatically set the InSight.
Jump to 3
Step
5
If you do not have a DHCP server, it will set as follows after one minute.
Initial address: Refer to the label on the InSight
User name: root
Default password: OPTEX
Change your password as appropriate.
Download IP installer;
https://navi.optex.net/firmware/50426
Refer to the InSight Camera manual for more details.
InSight Camera manual
https://navi.optex.net/manual/50426/en/?type=cameramanual
Setup your CHeKT Dealer Portal:
1. Go to http://dealer.chekt.com/ to log in.
2. Select the Customer on the left side of the dashboard.
3. Select the Site Devices tab.
4. Select the bridge device to be associated with the sensor camera.
5. Access the bridge settings using the gear icon to its right.
6. Select the appropriate tab to register the PIR camera.
Refer to the CHeCK support site for more details.
CHeKT support
https://support.chekt.com
4
Step
1
2
Remove the Back cover.
Raise the Back cover up.
Pull it back.
Adjust PIR area direction
4-1. Horizontal adjustment
12
Horizontal ±95°
1
2
6
Vertical 0° to -20°
Do not use the vertical angle adjustment of the main unit other than adjusting
the detection area surface to be parallel to the ground inclination.
Parallel
Adjust the detection range
Caution
Only one side
needs to be loosened.
NOTE
Camera angle and PIR area settings
4-2. Vertical adjustment
PIR area adjustment
1
Changing for each item in this step is optional.
Check the default settings and if no changes are required, proceed to the next item.
4
Step
7
Camera angle adjustment
2
Loosen screws to adjust camera angle
Angle can be adjusted by sliding the camera vertically.
Camera angle and PIR area settings
Default
20°min.
35°max.
30°
8
4
Step
Camera angle and PIR area settings
4-3. PIR/VCA settings
Refer to the InSight VCA manual for details on PIR and VCA area settings.
https://navi.optex.net/manual/50426/en/?type=VCAmanual
If the vertical angle of the camera is to be adjusted, adjustment of this
sections must be matched to ensure the best performance of the sensor.
Caution
Open the PIR cover
4-4. PIR area masking
1
4
Step
Camera angle and PIR area settings
Lock screw
(
Use as necessary)
* Remove before,
if used.
[1] Unlock the cover using a
screwdriver (-).
[2] Lift the PIR cover up.
Attach the area masking strips
a
b
c
d
b
c
d
ｆｆ
a
b
c
dｆ
b
c
dｆ
e
e
e
e
2
9
The default settings are 12.0 m (40') 120° wide.
If no masking of the detection area is required, proceed to the next item.
4-5. Switch settings
ON OFF
Alarm output N.O. N.C. Do not change *
LED ON OFF
3 4
3 4
3 4
3 4
Low
Middle
PIR sensitivity
High
Super High
1
2
3
4 56 7 8
Default
Default
Future use
Do not move the mirror nor PCB from the factory settings as Pet alley cannot be set.
Caution
Set the DIP switch 1 to 4, as necessary.
10
4
Step
Camera angle and PIR area settings
4-6. Put on the back cover
1
2
*Alarm output must be kept to N.C.
N.O. setting may cause unstable performance.
Andere Handbücher für InSight INS-QXI-ST
2
Inhaltsverzeichnis
Andere Optex Digitalkamera Handbücher
