Optima Home Scales COMMANDER-BT Series Bedienungsanleitung

1.0 explanation

COMMANDER-BT series has a stainless-steel pan, A variety of logos

displayed large backlit LCD. There are four easy to use function ，

，

COMMANDER-BT

USER MANUAL

，. With the corresponding power module.

2.0 Precautions

Power on/off

Press to hold the reading, refer to 11.4 & 11.5

Press to select unit: KG, Lb, Oz

Zero or tare the weight

⚫Please do not reduce the accuracy of the scales in place

⚫Do not place in direct sunlight or near extreme temperature

⚫Do not put on an unstable platform for weighing

⚫Avoid using with an unstable power source

⚫Do not place scale near machine vibration.

⚫Avoid high humidity and dust as it may cause malfunction of the scale

⚫Avoid placing the scale near air vents or windows

⚫Keep the scale clean of debris

Note: When moving the scale, be careful to avoid bending the connecting

cable and connector.

3.0 KEY

Platform and display

4.1 Platform

The platform works with 4*AA battery.

a.Power key:

Press power key for 2 seconds to activate the platform, and the

light will be flash every second, and light will be turn on if it is

connected to the indicator.

Press power key again to power off the platform. The light will turn

off.

b.Light

There are 4 status of the light. If the light is off, the platform is

asleep, or battery is low. If the light is on, the platform is connected

to the indicator and working. If the light flashes every second, the

platform is waiting to be connect to the indicator. If the light is flashing

every 0.5 second, the platform is low on power, and you need to be

replaced the battery.

c.Connection range

The platform and indicator are connected through wireless

Bluetooth communication. Be sure the distance between

indicator and platform is less than 5 meters without any obstacle.

Try to reduce to the distance if the indicator shows “bt-c”.

The connected distance will be shorter when the battery is low

on power. User can turn the platform to a certain angle for good

connection.

d.How long before you need to replace the battery

The platform can continuously work for about 100 hours if

alkaline battery is used. Ni-MH rechargeable batteries are

recommended.

4.2 Display of indicator

Symbol

description

The current scale is zero state

Weighing in stable

kg, lb, oz

Units can be used

Battery low power, the indicator needs you to replace

the battery or power with USB/adaptor

Tare, net weight display

HOLD

When the hold function on the display screen weighing

unchanged

4.0 A description of each indicator to identify

5.0 battery

Indicator: 4*AA battery or USB/adaptor

Platform: 4*AA battery

6.0 backlight display

LCD backlight can be set to remain open until closed or automatically

turned off (i.e., when using scales or press the start button) three

modes See details in section 11.2 how to setup

7.0 Auto power off function

Automatic shutdown feature can be turned off by the user to set this

feature or allow shutdown within a certain time frame for the scale,

details see section 11.1.

8.0

Operating Instructions

8.1

Power on

Press to power onthe indicator

ill

self-test,

and connect to

the platform with Bluetooth, be sure the platform within the

range 5 meter and battery is ok if “bt-c” is shown.

The platform’s led light will be on then, and the weight will

be show on the LCD of indicator.

press again will power off the indicator, and the platform

will power off too.

The scale can be set as desired by the user to control the weighing

8.2

Zero function

If the current weight on pan is less than 1 % of the max. capacity,

press to zero the scale.

8.3

Tare function

Press to tare the weight if the weight is less than max. capacity,

and the will be show on the display.

8.4 select units

press to select units

8.5 print/hold function

If communication output mode is set “pr” (refer to 11.4),

press

key

will send weight to the USB port. If hold mode is set “hod 3” (refer to

11.5), press key will hold the reading or cancel the hold.

9.0

External calibration

It may need to be re-calibrated after use for some time, or the reading

is not correct.

⚫In the normal weighing mode, the order press

+ + + + to external calibration. Enter the need for

external calibration weights weight (unit：KG) ，press

Increase value，to displacement.

⚫

Press

to confirm

Note: If you select a weight less than or greater than 10% of the

weighing ，there will display the “CALEr” err code. Press

external calibration.

to re

⚫After passing external calibration, scale will return to weighing

mode

11.0 User parameter settings

operation. Press to select, and press

to confirm.

11.1 auto power off function

⚫Turn off the scale press and turn on the scale, then release the

，displayed “Pr oFF” ，press to select “Pr oFF” or “Pr on”

1. Pr on：Enables the Auto Power Off function. The power will be

turned off after 2minutes if a key has not been pressed for 2

minutes and the scale is at zero. If there is any weight on the scale

or a key is pressed, the scale will continue to work.

2. Pr oFF：Disables the Auto Power Off function. The scale will not

automatically turn off.

Display will show “Hod 3” (DEFAULT SET).

1.Hod 1: No hold function

2.Hod 2: Automatic hold function, it will hold for 15 seconds when the

reading is stable.

3.Hod 3: Manual hold function, press hold key will hold the reading,

press again will cancel the hold reading.

Note: if output mode of communication is select “pr”, “hod 3” will be

disabled.

12. 0 USB INTERFACE

The scales come with a bi-directional USB interface.

Interface parameters are: USB

output of weighing data ASCII code

Selectable Baud

You should install the USB-Serial diver, and follow the driver

instruction, and then you can use the USB as a serial com.

Input commands format:

Z <cr> <lf>

Tares the scale to display the net weight- same as pressing

H <cr> <lf>

Sets the scale to hold if the hold function is enabled. Same

as pressing the key.

N <cr> <lf>

Sends the net weight to the USB interface.

G <cr> <lf>

Sends the gross weight to the USB interface.

T <cr> <lf>

Sends the tare weight to the USB interface.

11.4.1 SELECTION OF BAUD RATE

Display will show “b 9600” (DEFAULT SET) There are three

options: “b 2400”, “b 4800”, “b 9600”.

11.4.2 SELECTION OF OUTPUT MODE

Display will show “con” (default set), there are three

option: “on” (continue output), “st” (stable output), “pr” (print

out).

11.5 hold function

Output format:

Gross Weight

Net Weight

Tare Weight

11.2 Backlight settings

The second parameter is to set the backlight, display "bL 3"

(default setting)

1. bL 1: backlight always off

2. bL 2: always bright backlight

3. bL 3: If no weight on the pan, then the scale will

automatically turn the backlight or when the object is

removed after 10 seconds off the backlight after zeroing the

scale.

press to select，press to confirm and return to

weighing mode.

11.3 manage the Bluetooth

It will display “Axxxx” (xxxx: The address of the Bluetooth of

the platform), press + + + + to clear the address if you

need replace a new platform for indicator.

Note: a. the “xxxx” will be “FFFF” if there is no platform

connected before.

b. Please ensure only one platform is around you,

and re-power on the indicator to finish the

replace operation.

11.4 manage of USB communication

to confirm

Press

G + 2.00 kg <cr><lf>

N + 1.00 kg <cr><lf>

T + 1.00 kg <cr><lf>

Error code

phenomenon

Failure Analysis

"bt-c"

LCD display “bt-c” when

power on

The platform is not

at the range or lack

of battery

"-----"

overload

Weight on the pan

exceeds the capacity of

the scale. Remove the

weight from the pan.

CALEr

Input weight less than or

greater than 10% of the

weighing displayed “CALEr”

Lead to incorrect

calibration, re-

calibration process

is repeated correctly

Always show “Lo”, the key

operation is invalid (except

the power button)

Indicator lack of

power supply, need

replace, or input

USB/adaptor

bat-0

LCD show “Lo”, platform is

flash fast every 0.5 second

The battery of the

platform needs to

be replaced

When an error message appears, try rebooting, calibration factors

or other ways to relieve some of the problem may lead to errors, if

the error message still appears, find the proxy service provider

contact

There may be some error messages during the boot process is running,

the following error message:

Error

13.0

Inhaltsverzeichnis

Andere Optima Home Scales Skala Handbücher

Optima Home Scales

Optima Home Scales ESSENCE Bedienungsanleitung

Optima Home Scales

Optima Home Scales GALAXY Bedienungsanleitung

Optima Home Scales

Optima Home Scales COMET Bedienungsanleitung

Optima Home Scales

Optima Home Scales GEMINI Bedienungsanleitung

Optima Home Scales

Optima Home Scales PROFILE Bedienungsanleitung

Optima Home Scales

Optima Home Scales METEOR Bedienungsanleitung

Optima Home Scales

Optima Home Scales ECLIPSE Bedienungsanleitung

Optima Home Scales

Optima Home Scales SHADOW Bedienungsanleitung

Optima Home Scales

Optima Home Scales LUNA Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung