Optoma A16 Bedienungsanleitung

INSTALLATION INSTRUCTION

A16 UST lens

Content

Projector system requirement......................................................................2

Required accessories and tools...................................................................2

Entering UST mode for installation setup ...................................................4

Removing the non-UST lens.........................................................................4

Boresight pre-adjustment .............................................................................4

Installing UST lens boresight module..........................................................6

Installing the lens supporter.........................................................................7

Installing ceiling mount with lens supporter...............................................9

Installing the UST lens ................................................................................11

Turning the projector on..............................................................................12

Image adjustment ........................................................................................12

Lens focus adjustment.........................................................................12

Boresight adjustment...........................................................................13

Attaching the lens supporter to the UST lens...........................................14

Removing the UST lens...............................................................................14

Change back to the non-UST lens after using the UST lens....................15

Releasing the UST lens boresight module ................................................15

A16 UST LENS INSTALLATION

INSTRUCTION

This user manual is designed to assist with the installation of the BX-CTA16 UST lens

in your Optoma projector. Before attempting to fit the UST lens, please read through

this document in full order to ensure installation steps are made correctly.

Projector system requirement

Firmware version xxxx or higher is mandatory for correct UST lens installation or

operation.

To check the firmware version in the projector menu, select: OPTION > Information.

ZU660: requires firmware version V04.10 or higher

ZU850: requires firmware version V03.77 or higher

ZU1050: requires firmware version V00.29 or higher

Required accessories and tools

Check that the following items (A-L) are included in the package. Prepare the required

tools (I, II, III) for installing each item.

Item

Image

Name of item

Quantity included

UST lens

UST lens boresight

module

Lens mount bracket

Bracket

Lens supporter

M3 X L8 screws

M3 X L8 hex screws

M6 X L22 hex

screws

M3-3.7 x 0.8 x 18

washer

M6-6.7 x 1 x 16

washer

Boresight extender

Entering UST mode for installation setup

To complete the UST lens setup, follow the steps below.

1. Power on the projector with a non-UST lens.

2. In the projector menu, follow these steps: Option > Service > UST Lens Install

> Start.

To enter service menu, enter the password “Left, Down, Right, Up”or “1, 5,

9, 0”.

3. Press Exit to turn off the projector.

4. Disconnect the AC cable.

Note: If an additional non-UST lens is not available, RS232 command, “~XX361 1”, or

hot key “Exit, Input, Left, Right” can be used to do UST lens calibration. After UST

lens calibration, the projector would automatically power off.

Removing the non-UST lens

To remove the non-UST lens, follow the steps below.

1. Make sure projector is turned off before removing the non-UST lens.

2. Rotate the non-UST lens counter-clockwise by a quarter to release the lens.

3. Remove the non-UST lens from the front aperture of the projector.

Boresight pre-adjustment

The UST lens boresight module needs to be adjusted before fitting to the projector.

1. Make sure the boresight gears are in the initial state.

If not, turn the small boresight gears counter-clockwise to the end position,

where 2 marks are roughly aligned.

L shape tool

2. Turn the boresight gears clockwise according to the desired projector

orientation.

Note: The ZU850 has a different orientation table from ZU660 and ZU1050.

Installing UST lens boresight module

To install UST lens boresight module, complete the following steps.

1. Remove 3 screws with a Philips #2 screwdriver from the non-UST lens

boresight module.

2. Release the non-UST lens boresight module from projector.

1. Release the lens cable from the original holder on the plate.

2. Install the UST lens boresight module into the projector.

The boresight module needs to be adjusted before fitting to the unit.

See Boresight pre-adjustment.

3. After installing UST lens boresight module, fasten using 3 screws with a

Philips #2 screwdriver.

4. Insert the cable back into the UST lens boresight module.

Note: Ensure the cable is not wrapped or pinched when fastening the UST

lens boresight module.

Installing the lens supporter

An additional lens supporter is required for this lens. Complete the following steps to

install the lens supporter.

1. Place the lens and projector upside-down on the cushioned surface.

2. Use a Philips #2 screwdriver to fasten the lens mount bracket on to the UST

lens with 2 M3 X L8 screws.

Note: Ensure the arrow on lens mount bracket is facing out from the lens

mount.

3. To avoid the lens supporter touching the surface, turn the projector feet at

least 5 counter-clockwise turns.

4. To pre-lock the bracket on to the lens supporter use a 2.5 mm allen key with 1

M3 x L8 hex screw and M3-3.7 X 0.8 X 18 washer.

Note: Do not fully tighten the screws until the lens has been installed.

Lens supporter

M6-6.7 x 1 x 16 washers

M6 X L22 hex screws

M3 X L8 screws

Lens mount bracket

UST lens

Lens mount

5. Attach the lens supporter to the bottom of the projector.

6. To fasten the lens supporter on to the mounting holes use 5 mm allen key

with 2 M6 x L22 hex screws and 2 M6-6.7 x 1 x 16 washers.

Installing ceiling mount with lens supporter

To install this lens in ceiling mount, complete the following steps.

Note: Due to thermal requirement, user needs to keep at least 30mm between the

ceiling mount plate and bottom intake. Furthermore, user would need to prepare

adapter A, adapter B, M6 ceiling mount screws and ceiling mount plate that are not

included in the package list.

Lens supporter

M6-6.7 x 1 x 16 washers

M6 X L22 hex screws

bracket

M3-3.7 x 0.8 x 18 washer

M3 X L8 hex screw

Inhaltsverzeichnis

Andere Optoma Projektorzubehör Handbücher

Optoma

Optoma Projector Bedienungsanleitung

Optoma

Optoma BX-AL133B Bedienungsanleitung

Optoma

Optoma OWM3000 Bedienungsanleitung

Optoma

Optoma ALR100 Installationsanleitung

Optoma

Optoma BM-3300ST Bedienungsanleitung

Optoma

Optoma BM-9005U Bedienungsanleitung

Optoma

Optoma DS-9106MGA Handbuch

Optoma

Optoma ZF2100 Glasses Bedienungsanleitung

Optoma

Optoma OWM855 Bedienungsanleitung

Optoma

Optoma BM-5001U Leitfaden

Optoma

Optoma BX-AL133 Bedienungsanleitung

Optoma

Optoma 3D-XL Bedienungsanleitung

Optoma

Optoma UHDCast Pro Kurzanleitung

Optoma

Optoma PCT-101 Bedienungsanleitung

Optoma

Optoma CM-E75X Bedienungsanleitung

Optoma

Optoma TX778W Bedienungsanleitung

Optoma

Optoma WPS Bedienungsanleitung

Optoma

Optoma WS-9211G Bedienungsanleitung

Optoma

Optoma BX-AL133B Bedienungsanleitung

Optoma

Optoma 3D-RF System Bedienungsanleitung

Optoma

Optoma OWM1000 Bedienungsanleitung

Optoma

Optoma A16 UST Series Bedienungsanleitung

Optoma

Optoma AKPro Bedienungsanleitung

Optoma

Optoma 3D-XL Technisches Handbuch

Beliebte Projektorzubehör Handbücher anderer Marken

PEERLESS

PEERLESS PE 1120 Leitfaden

Osram

Osram SIRIUS HRI Series Handbuch

Presentation Switchers

Presentation Switchers PS111 Bedienungsanleitung

Kramer

Kramer VIA GO Bedienungsanleitung

Yamaha

Yamaha PJL-112 Stücklistenhandbuch

Mitsubishi Electric

Mitsubishi Electric 236CB Betriebsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Acer

Acer WP100 Bedienungsanleitung

i3 i3board Bedienungsanleitung

CHIEF

CHIEF HB-43E Bedienungsanleitung

Biamp

Biamp Modena Hub Service-Handbuch

NEC

NEC MP10RX Bedienungsanleitung

Panamorph

Panamorph DCR-S3 Bedienungsanleitung

Exact solutions

Exact solutions FRAME-EVO-P10 Bedienungsanleitung

CHIEF

CHIEF VCM103S Bedienungsanleitung

InFocus

InFocus LP70+ Leitfaden

Sharp

Sharp AN-PH20EZ Bedienungsanleitung

Ipevo

Ipevo WPS-HD Bedienungsanleitung