Optoma H55 Bedienungsanleitung
English
1
Usage Notice
Precautions ...........................................................................................2
Introduction
Product Features...................................................................................3
Package Overview ................................................................................4
Product Overview..................................................................................5
Main Unit ..........................................................................................5
Panel Control....................................................................................6
Connection Ports..............................................................................6
Full function wireless remote controller.............................................7
Installation
Connecting the Projector .......................................................................8
Powering On/Off the Projector...............................................................9
Power On the Projector ....................................................................9
Power Off the Projector ....................................................................10
Adjusting the Projected Image...............................................................11
Adjusting the Projector Height ..........................................................11
Adjusting the Projector Zoom/Focus.................................................12
Adjusting Projection Image Size .......................................................12
User Controls
Panel Control & Remote Control............................................................13
On-Screen Display Menus ....................................................................16
How to Operate ................................................................................16
Image-I (Computer mode) ................................................................17
Image-I (Video mode).......................................................................18
Image-II (Computer mode) ...............................................................19
Image-II (Video mode)......................................................................20
Audio................................................................................................21
Language .........................................................................................21
Management.....................................................................................22
Appendices
Troubleshooting.....................................................................................23
Changing the Lamp ...............................................................................25
Specifications ........................................................................................26
Compatibility Modes ..............................................................................27
Table of Contents
English
2
Usage Notice
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user’s guide to maximize the life of your unit.
Warning- Do not look into the lens. The bright light may hurt your eyes.
Warning- To reduce the risk of fire or electric shock, do not expose this
product to rain or moisture.
Warning- Please do not open or disassemble the product as this may cause
electric shock.
Warning- When changing the lamp, please allow unit to cool down, and follow
all changing instructions.
Warning- This product will detect the life of the lamp itself. Please be sure to
change the lamp when it shows warning messages.
Warning- After changing a new lamp, please reset the lamp life from OSD
menu.
Warning- Before switching off the product, please keep the cooling fan
running for a few minutes.
Warning- When connecting the projector to computer, please turn on the
projector first.
Warning- To reduce the risk of injury to the eyes, do not look directly into the
laser light on the remote control and do not point the laser light into
anyone’s eyes. This remote control is equipped with a Class II laser
that emits radiation.
Warning- When the lamp reaches the end of its life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn back on until the lamp module has been replaced. To replace the
lamp, follow the procedures listed under “Changing the Lamp”.
Do:
vTurn off the product before cleaning.
vUse a soft cloth moistened with mild detergent to clean the display
housing.
vDisconnect the power plug from AC outlet if the product is not being
used for a long period of time.
Don’t:
vBlock the slots and openings on the unit provided for ventilation.
vUse abrasive cleaners, waxes or solvents to clean the unit.
vUse under the following conditions:
- Extremely hot, cold or humid environment.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
English
3
Product Features
This product is an XGA single chip 0.7” DLPTM projector. The
outstanding features of it are listed as follows:
uTrue XGA, 1024 x 768 addressable pixels
u6.4 lbs (2.9 kgs) compact design
u1000 ANSI Lumens high brightness
uHigh contrast ratio 1000 : 1
uSingle chip DLPTM technology
uPureProgressiveTM processing technology for artifact-free film
materials.
uHDTV compatible (480P,1080i,720P)
uNTSC/NTSC4.43/PAL/PAL-M/PAL-N/SECAM and
HDTV compatible
uHigh-tech DVI connection for digital and analog video
connectivity
uFull function wireless remote controller
uMultimedia audio integration
uUser friendly multilingual on-screen display menu
uAdvanced electronic keystone correction
uUser friendly control panel
uLuxurious carrying case included
uSXGA compression and VGA, SVGA re-sizing
u200 Watts user replaceable UHP lamp
uMac compatible
Introduction
English
4
Package Overview
This projector comes with all the items shown below. Check to make sure
your unit is complete. Contact your dealer immediately if anything is
missing.
RS232 Cable
S-Video Cable
VGA Cable
Wireless Remote Controller
Carrying Case
Audio Cable Jack/RCA
DVI to D-Sub Cable
Battery x 2User’s Guide
Introduction
Composite Video Cable
2
34 5
6
Projector with lens cap
D-Sub to RCA Cable for
HDTV/Component
7
1
User’s Manual Power Cord
(According to Country)
English
5
Main Unit
Product Overview
Introduction
1. Panel Control
2. Power Connector & Power Switch
3. Connection Ports
4. Focus Ring
5. Zoom Lens
6. Zoom Ring
7. Speaker
8. Remote Control Receiver
9. Elevator Button
10. Elevator Foot
1
2
3
4
5
8
6
7
910
English
6
Introduction
Panel Control
Connection Ports
1 RS232 Input Connector
2. Audio Input for Video
3. Composite Video Input Connector
4. S-Video Input Connector
5. Audio Input for DVI
6. DVI Input Connector
7. Audio Input for Computer
8. PC Analog Signal/HDTV/Component Video Connector
9. Audio Output Connector
10. 12V Relay Connector
11. Power Switch
12. Power Connector
2
3
4
5
6
9
7
810
11
12
1. Lamp Warning LED
2. Temperature Warning LED
3. Volume
4. Mute
5. Menu (On/Off)
6. Four Directional Select Keys
7. Enter
8. Zoom
9. Re-sync
10. Source
11. Power /Standby
1
2
3
4
5
8
6
7
9
10
11
1
English
7
Full Function Wireless Remote Controller
Re-sync
Video Source
Menu
Four Directional Select
Keys
S-Video Source
16:9/4:3 Aspect Ratio
Backlight
Introduction
Power
Computer Source
HDTV Source
Freeze
Color Temperature
Brightness
Contrast
Mute
Volume
Keystone Correction
Zoom
Enter
English
8
1. RS232 Cable
2. VGA Cable
3. S-Video Cable
4. Audio Cable Jack/RCA
5. Composite Video Cable
6. DVI to D-Sub Cable
7. D-Sub to RCA Cable for HDTV/
Component
Connecting the Projector
Installation
vTo ensure the projector works well with your computer, please configure the
display mode of your graphic card to make it less than or equal to 1024 X 768
resolution. Make sure timing of the display mode is compatible with the
projector. Refer to the “Compatibility Modes” section on page 27.
S-Video Output
Video Output 1
2
3
4
7
6
Digital Tuner Output
Digital Tuner Output
Antenna
RS232
AUDIO
VIDEO
S-VIDEO
AUDIO AUDIO AUDIO
DVI
COMPUTER
+12V RELAY
INPUT OUTPUT
RGB
RS232
5
English
9
Lens cap
Power / Standby
Installation
Powering On the Projector
1. Remove the lens cap.
2. Ensure that the power cord and signal cable are securely connected.
3. Turn on the main power switch on the side of the projector and allow the
projector to warm up for 1-2 minutes.
4. Turn on the lamp by pressing “Power/Standby” button on the control
panel.
The startup screen will display and count down for 20 seconds and the
Power/Standby indicator will light solid amber.
The “LAMP” LED indicator will light solid green.
5. Turn on your source (computer, notebook, or video player ,etc...) The
projector will detect your source automatically.
vIf the screen displays “No Signal” , please make sure the signal cables are
securely connected.
vIf you connect multiple sources at the same time, use the “Source” button on the
Remote Control or Panel Control to switch.
Power On/Off the Projector
vTurn on the projector first and
then the computer.
Power Switch
1
2
3
English
10
Installation
Powering Off the Projector
1. Press the “Power/Standby” button to turn off the projector lamp.
2. After pressing the “Power/Standby” button, you will see a message
“Power off the lamp?” on the on-screen display. Press the “Power/
Standby” button again to confirm. Otherwise the message will disappear
after 5 seconds.
3. “Power/Standby” LED indicator will light solid amber for about 30
seconds. After the “Power/Standby” indicator starts flashing, you can
turn off the main power switch on the side of the projector.
If you want to turn on the projector, you must press the “Power/
Standby”button within 90 seconds of the start of the indicator flashing.
4. Do not turn on the projector immediately following a power off
procedure.
vWhen the “LAMP” indicator flashs green for about 10 seconds, you will see a
message “Fan Fail” on the on-screen display. Please contact your local dealer or
Optoma service center.
vWhen the “TEMP” indicator lights solid orange, it indicates the projector
has been overheated. You will see a message “Over Temperature” on the on-
screen display. The projector will automatically shut itself down.
Under normal conditions, the projector can be switched on again for your
presentation. If the problem persists, you should contact your local dealer or
Optoma service center.
Andere Handbücher für H55
1
Inhaltsverzeichnis
Andere Optoma Projektor Handbücher
Optoma
Optoma TX612-3D Bedienungsanleitung
Optoma
Optoma HD83 Bedienungsanleitung
Optoma
Optoma HD8600 Bedienungsanleitung
Optoma
Optoma EH416 Bedienungsanleitung
Optoma
Optoma DH1010 Bedienungsanleitung
Optoma
Optoma TW631-3D Bedienungsanleitung
Optoma
Optoma HD33 Bedienungsanleitung
Optoma
Optoma EX531 Bedienungsanleitung
Optoma
Optoma ES515 Bedienungsanleitung
Optoma
Optoma HD72 Bedienungsanleitung
Optoma
Optoma EP780 Bedienungsanleitung
Optoma
Optoma H57 Bedienungsanleitung
Optoma
Optoma TX775 Bedienungsanleitung
Optoma
Optoma EW695UTis Bedienungsanleitung
Optoma
Optoma HD700X Bedienungsanleitung
Optoma
Optoma DS317 Technisches Handbuch
Optoma
Optoma DV10 MovieTime Bedienungsanleitung
Optoma
Optoma PlayTime PT105 Bedienungsanleitung
Optoma
Optoma EzPro 705 Bedienungsanleitung
Optoma
Optoma EX612 Bedienungsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
