Optoma Theme Scene HD82 Gebrauchsanweisung
SERVICE MANUAL
SI : Qiue TSE: Check: Approved:
Date Revise Version Description
2008.12.29 V1.0 Initial Issue
2009.01.06 V2.0
Modify CH2,CH4
(Change “press power → left → left → up” to “press
power off → left → left → up“
2010.02.22
V3.0 Modify CH4 “Defect specication table“
HD82/HD8200
Copyright February, 2010. All Rights Reserved P/N:36.8AF05G001
Condential
I
Preface
This manual is applied to HD82/HD8200 projection system. The manual gives you a brief
description of basic technical information to help in service and maintain the product.
Your customers will appreciate the quick response time when you immediately identify
problems that occur with our products. We expect your customers will appreciate the
service that you offer them.
This manual is for technicians and people who have an electronic background. Please
send the product back to the distributor for repairing and do not attempt to do anything that
is complex or is not mentioned in the troubleshooting.
Notice: The information found in this manual is subject to change without prior notice. Any
subsequent changes made to the data herein will be incorporated in future edition.
HD82/HD8200 Service Manual
Copyright February.2010
All Rights Reserved
Manual Version 3.0
HD82/HD8200
Condential
HD82/HD8200
II
Table of Content
Chapter 1 Introduction
Highlight 1-1
Compatible Mode 1-2
Chapter 2 Disassembly Process
Equipment Needed & Product Overview 2-1
Disassemble Lamp Cover Module 2-2
Disassemble Lamp Module 2-2
Disassemble Bottom Cover Module 2-3
Disassemble Formatter Board Module 2-3
Disassemble Main Board and I/O Board Module 2-5
Disassemble Lens Ring Module 2-6
Disassemble Top Cover Module 2-7
Disassemble Top Shielding Module 2-7
Disassemble Right Cover Module 2-8
Disassemble Daught Board Module 2-10
Disassemble System Fan Module 2-11
Disassemble Lamp Driver Module 2-13
Disassemble DMD Blower 2-14
Disassemble Optical Engine Blower 2-15
Disassemble Engine Module 2-16
Disassemble Color Wheel Module 2-16
Disassemble Lamp Blower Duct Module 2-18
Disassemble DA Cover 2-18
Disassemble DA Motor Module 2-19
Condential
III
Disassemble Rod Module 2-20
Disassemble Heat Sink Module 2-20
Disassemble DMD Module 2-21
Disassemble Focus Ring 2-21
Disassemble Zoom Ring Module 2-22
Disassemble Lamp Blower Module 2-22
Disassemble Air Duct Module 2-23
Disassemble Left Cover Module 2-23
Disassemble LVPS Module 2-25
Disassemble Thermal Sensor Board 2-26
Disassemble Bottom Cover Shielding Module 2-27
Disassemble Ceiling Base Module 2-27
Rod Adjustment 2-28
Re-write Lamp Usage Hour 2-29
Chapter 3 Troubleshooting
LED Lighting Message 3-1
Main Procedure 3-2
Chapter 4 Function Test & Alignment Procedure
Test Equipment Needed 4-1
Service Mode 4-1
OSD Reset 4-1
Test Condition 4-2
Test Inspection Procedure 4-4
PC MODE 4-4
Video Performance 4-8
Calibration 4-9
HD82/HD8200
Condential
HD82/HD8200
IV
DA Calibration 4-11
Optical Performance Measure
4-11
Others
4-13
Chapter 5 Firmware Upgrade
Equipment Needed
5-1
Setup Procedure
5-2
Firmware Upgrade Procedure
5-3
Port95nt.exe Installation 5-5
8051 Firmware Upgrade Procedure 5-7
Chapter 6 EDID Upgrade
EDID Introduction
6-1
Equipment Needed
6-2
Setup Procedure(VGA & DVI-D Port)
6-3
EDID Key-In Procedure(VGA & DVI-D Interface) 6-3
Setup Procedure (HDMI 1 Port & HDMI 2 Port )
6-6
EDID Key-In Procedure(HDMI 2 Interface)
6-6
Appendix A
Exploded Image
1
Appendix B
SerialNumberSystemDenition 22
PCBACodeDenition 23
HD82/HD8200 1-1
Chapter 1
Introduction
1-1 Highlight
No
1
2
8
10
11
12
HD82/HD8200
1-2
No
18
20
21
1-2 Compatible Mode
Computer compatibility
1280×800
HD82/HD8200
HD
HD
Note: "V" expressed support this type of signal and "X" expressed that does not support this
type of signal.
HD82/HD8200 Condential 2-1
Chapter 2
Disassembly Process
2-1 Equipment Needed & Product Overview
1. Screw Bit (+) :105
2. Screw Bit (+) :107
3. Screw Bit (-) :107
4. Hex Sleeves 5 mm
5. Tweezers
6. HD82 unit
* Before you start: This process is protective level II. Operators should wear electrostatic chains.
* Note: If you need to replace the main board, you have to record the lamp usage hour.
Condential 2-2
HD82/HD8200
2-3 Disassemble Lamp
Module
1. Unscrew 2 screws (as red circle) on the
lamp module.
2. Take off lamp module from the projector.
2-2 Disassemble Lamp
Cover Module
1. Turn the projector backside.
2. Push the lamp cover switch to the
open state (as the red oval-shaped
circle).
3. Disassemble lamp cover module.
Andere Handbücher für Theme Scene HD82
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Optoma Projektor Handbücher
Optoma
Optoma DVD100 Bedienungsanleitung
Optoma
Optoma HD2200 Bedienungsanleitung
Optoma
Optoma Pico PK320 Bedienungsanleitung
Optoma
Optoma TW6000 Bedienungsanleitung
Optoma
Optoma W401 Bedienungsanleitung
Optoma
Optoma EX762 Bedienungsanleitung
Optoma
Optoma EP737 Bedienungsanleitung
Optoma
Optoma TW635-3D Bedienungsanleitung
Optoma
Optoma W307UST Bedienungsanleitung
Optoma
Optoma MovieTime DV11 Bedienungsanleitung
Optoma
Optoma PRO160S Bedienungsanleitung
Optoma
Optoma H100 Bedienungsanleitung
Optoma
Optoma ML300 Bedienungsanleitung
Optoma
Optoma ZW300USTe Bedienungsanleitung
Optoma
Optoma DS216 Bedienungsanleitung
Optoma
Optoma S310 Bedienungsanleitung
Optoma
Optoma HD6720 Bedienungsanleitung
Optoma
Optoma Optoma EP747 Technisches Handbuch
Optoma
Optoma EP719 Bedienungsanleitung
Optoma
Optoma EP737 Gebrauchsanweisung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
