Orbit OSLPIR240B Bedienungsanleitung

OSLPIR240B is a 240 degree standalone motion

sensor with fully automatic indoor and outdoor

security/courtesy lighting control. An adjustable timer

lets you select how long the light stays on after

activation. The Lux and sensitivity settings are also

adjustable according to your needs.

This model comes with the following operation modes:

(1) Auto: automatic operation

(2) Manual override: When the light is on, turn the wall

switch off and on twice within 4 seconds to enter

manual override operation.

Note: Read this entire manual before you start to

install the system.

PRODUCT OVERVIEW

Main Body

Back Plate

Corner Mounting Plate

Attachment Ring

Lens

Control Knobs: Under the ring; from left to right:

Time, Sensitivity, and Lux control knobs

SAFETY NOTICE

Avoid installing the unit in storming or raining

weather.

Be sure to isolate or switch off power source

before installing or maintenance.

Make sure that the power wiring comes from

circuit with an external 16A miniature circuit

breaker for the short circuit protection or a

suitable fuse.

IMPORTANT

Installation must be performed by skilled

technicians who are informed about the standards

and technical requirements of the appliance and its

proper installation.

Check your local codes as they apply to your

situation. If the house wiring is of aluminum,

consult with an electrician about proper wiring

methods.

Before proceeding with the installation, TURN OFF

THE POWER TO THE LIGHTING CIRCUIT AT

THE CIRCUIT BREAKER OR FUSE BOX TO

AVOID ELECTRICAL SHOCK.

CHOOSING THE MOUNTING LOCATION

When deciding a proper location to install the unit,

please take the following points into consideration:

This unit is designed to be installed indoor or

outdoor on the wall/ceiling with the lens facing

downwards. Install the unit wrongly may impair

its functionality. (FIGURE 1a & 1b)

FIGURE 1a

OSLPIR240B

240° Professional Motion

Sensor

INTRODUCTION



FIGURE 1b

For the best results, fix your sensor on a solid

surface, 2 meters above the ground.

For outdoor installation, a location under eaves is

preferable.

Avoid aiming the motion sensor at pools, heating

vents, air conditioners, or objects which may

change temperature rapidly.

Do not allow sunlight to fall directly on the front of

unit.

Avoid pointing the unit at trees or shrubs or where

the motion of pets may be detected.

The motion sensor is more sensitive to objects

moving across its field of detection. It is less

sensitive to objects moving directly towards the

sensor head. (FIGURE 2)

FIGURE 2

Select a location for the unit based on the

coverage angles shown in FIGURE 3.

FIGURE 3

INSTALLATION

Prepare a drill and a screwdriver at hand, and then

start the installation:

Wall Mounting Installation (FIGURE 4)

Remove the Back Plate (retained by 1 screw on

the bottom) from the main body.

Install the Back Plate with two screws on a

desirable place on the wall.

After correct wiring connection, fix the main body

to the Back Plate by screwing the screw on the

bottom.

FIGURE 4

Note: If the mounting location is around the corner,

use the Corner Mounting Plate to fix the Back Plate

and the main body as indicated below (FIGURE 5 &

6):

FIGURE 5

FIGURE 6

WIRING INSTRUCTION

(1) Switch off the power source or wall switch.

(2) Remove the Back Plate (retained by 1 screw on

the bottom) from the main body.

(3) Make a pin hole (up to 2 pin holes available) in

the center of the cable gasket on the Back Plate.

(FIGURE 7)

FIGURE 7

(4) Force the cable through the seal and unscrew two

screws on the pressure block.

(5) Strip approximately 6-8mm insulating part of the

wires from the power cord.

(6) Before connecting, ensure that the main body

gasket is firmly seated in its original place.

Note: The power cord must meet H05RN-F,

1.0mm² requirements.

(7) Connect the BROWN wire (Live wire) of the

power cord to the terminal block "L" mark.

Connect the BLUE wire (Neutral wire) of the

power cord to the terminal block “N” mark.

Connect the Live wire of lamp fixture to the

terminal block "LS" mark.

Connect the Neutral wire of lamp fixture to the

terminal block "N1" mark.

If the lamp fixture comes with the green/yellow

(Earth) wire, you can fix the wire to the terminal

block " " mark. Note that the terminal helps

fix the wire of lamp fixture but does not provide

grounding function. (FIGURE 8)

FIGURE 8

Install a wall switch adjacent to the power source

(FIGURE 9). The wall switch will help you in

switching the unit to manual override mode.

Please refer to the OPERATION section for more

information.

Load

Power

FIGURE 9

TEST / ADJUST THE SENSOR AND

LIGHTING SYSTEM

Prepare a flathead screwdriver for adjusting the

control knobs. To access the control knobs, pull off

the attachment ring from the top lens segment by

pressing two concave surfaces on the ring (FIGURE

10). After setting, fix the cover back to its place.

FIGURE 10

(1) TEST THE SENSOR

Turn the TIME and the LUX control knobs

counterclockwise to the edge - the TEST position.

(FIGURE 11)

FIGURE 11

Turn the power on, and the sensor will take about

90 seconds to warm up. During the period the

light may flash one time. After warm-up, the light

will turn off and you may take a walk test and the

light will turn on. This confirms that the wiring

was done properly and that the light is working.

Walk through the coverage area. The light will

turn on when motion is detected. Wait until the

light turns off and then move again to test the

sensor.

(2) SETTINGS

TIME ADJUSTMENT (FIGURE 12)

The TIME control knob determines how long the light

will stay on after motion is detected. Turn the TIME

control knob counterclockwise to decrease the light-on

duration (down to 5 seconds). Turn the TIME control

knob clockwise to increase the duration (up to 12

minutes).

FIGURE 12

LUX ADJUSTMENT (FIGURE 13)

The LUX control knob determines at which ambient

Lux level the connected light will turn on when the

sensor is in Automatic Operation mode.

The adjustable Lux range is between 20 and 200 Lux.

Turn the LUX control knob clockwise to the MOON

position and the light will only turn on at night (below

20 Lux). Turn the LUX control knob counterclockwise

to increase the Lux setting. Note that the “T”position

is for TEST mode. Adjust the control knob depending

on your requirements.

FIGURE 13

SENSITIVITY ADJUSTMENT (FIGURE 14)

The Sensitivity control knob determines the detection

distance of the sensor. The detection distance can

be adjusted so that user can prevent undesired light

triggers. Turn the control knob clockwise to increase

the detection distance (up to 12 meters) or

counterclockwise to decrease the detection distance

(down to 3 meters).

SENS SENS

FIGURE 14

SENSOR SWIVEL ADJUSTMENT (FIGURE 15)

Depending on individual need, the motion sensor can

be adjusted horizontally 90° to the left or 90° to the

right.

FIGURE 15

DETECTION RANGE ADJUSTMENTS

For limiting the detection range the clip-on lens covers

can be used to blank off lens segments. For different

requirements, the clip-on lens covers can be cut to

size horizontally and vertically to set detection

coverage. (FIGURE 16)

FIGURE 16

1. Follow the grooves on the covers, and cut it to the

suitable size to blank off the lens segment for the

undesirable detection area.

2. Press the two concave surfaces on the attachment

ring to pull off the ring.

3. Place the covers onto the notches at the sensor

lens top. The attachment ring is replaced to the

unit holding the covers steadily in place.

OPERATION

Depending on your needs, you can switch the unit

between the following operation modes: Automatic

Operation and Manual Override.

(1) Automatic Operation

Turn on the wall switch. After 90 seconds warm-up

the sensor will enter Automatic Operation. When the

sensor detects motion and the ambient light level is

lower than the LUX setting, the connected light will

automatically turn on. The light will stay on for the

duration of TIME setting and then turn off. Note that

if motion is detected again while the light is still on, the

time counting will be reset.

(2) Manual Override

To keep the light on regardless of the motion, you can

override the automatic operation. To enable Manual

Override mode, first ensure that the light is on and

then turn the wall switch off and on twice (off-on, off-on)

within 4 seconds. The interval between the first and

second operation must be within 0.5 - 2 seconds.

In Manual Override mode, the light will remain on for

around 5 hours. After 5 hours the light will turn off and

the motion sensor will revert to Automatic Operation.

Users can also manually set the motion sensor back to

Automatic Operation by turning off the wall switch for

at least 10 seconds and then turning it back on.

TROUBLESHOOTING

Light does not turn on

Confirm that you have made a correct “wiring

connection”.

Make sure that the bulbs have not burned out.

Light remains on

Make sure the wiring connection is correct.

If you set the system to manual override,

remember that you must turn the wall switch off

for at least 10 seconds to turn off the lights.

Check if the TIME setting is correct.

Others

The specification of protective shield shall consult

the local service agent.

SPECIFICATIONS

Power Requirement

AC 220 - 240V / 50Hz

Lighting Load

Incandescent Max. 2000W;

Fluorescent Max. 1000W

Detection Angle

Up to 240° at 20°C, 2m height

Detection Distance

Up to 12m at 20°C, 2m height

Swiveling Angle

90° leftward or 90° rightward

Mounting Height

Recommended:

1.8 - 2.5m (5.9 - 8.2 Ft) for Wall

Mount

2.5 - 4.0m (8.2 - 13.1Ft) for

Ceiling Mount

Sensor Operation

Auto / Manual Override

Time Adjustment

5 sec - 12 min

Lux Adjustment

20 - 200 Lux

Warm Up Time

90 seconds

Working Temperature

-20°C - 40°C / -4°F - 104°F

Protection Class

Class II

Protection Degree

IP44

Safety

*Specifications are subject to change without prior notice.

A501111862R01 2013/08

WARRANTY:

Your product is warranted against faults and manufacture when used

in normal domestic use for a period of one year.

We undertake to replace this product at no charge if found to be

defective due to a manufacturing fault during the warranty period.

This warranty excludes damage caused by misuse, neglect, shipping

accident, incorrect installation, or work carried out by anyone other

than a qualified electrical service technician.

If your product fails to operate satisfactorily, please return it to the

retailer from whom it was purchased to obtain a repair or

replacement product. You will need to produce satisfactory evidence

of date of purchase. If the product is to be replaced (cannot be

repaired) then that replacement will be of the same or similar product

or accessory excluding packaging, instruction card etc.

In New Zealand product is covered by the Consumers Guarantee Act

(1993). In accordance with the act consumers are advised that:

The manufacturer does not undertake that repair facilities and parts

are necessarily available for this product.

In Australia, our goods come with guarantees that cannot be

excluded under the Australian Consumer Law. You are entitled to a

replacement or refund for a major failure and compensation for any

other reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure.

Inhaltsverzeichnis

Andere Orbit Sicherheitssensor Handbücher

Orbit

Orbit ISIMAT+ Bedienungsanleitung

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung