Oreon EMPRESS E 650 Series Bedienungsanleitung

V20200201E

EMPRESS

THE DUTCH POWERHOUSE

(E 650 XXX YY)

INSTALLATION MANUAL

IMPORTANT: READ CAREFULLY BEFORE STARTING INSTALLING THE

FIXTURE. KEEP FOR FUTURE REFERENCE.

–3 –V20200201E

PREFACE

Thank you for purchasing the Dutch Powerhouse Empress (E 650 XXX YY)

This manual contains all the information needed to quickly familiarize yourself with the LED xture. We

kindly request you to read through this information carefully, before you start installing the LED xture.

This manual does not provide information of the electrical system, water-cooling system and mounting

system. These systems must be designed/provided by the installer.

This manual is intended for the installer of the Dutch Powerhouse Empress (E 650 XXX YY). This manual is

originally written in English. All other languages are translations of the original manual. Keep this manual

safe!

This manual contains warnings that point out hazardous situations and important

remarks. These warnings and remarks are grouped and represented as follows:

DANGER

Danger! The signal word that indicates a hazard with a high level of risk which, if not avoided,

will result in death or serious injury.

WARNING

Warning! The signal word that indicates a hazard with a medium level of risk which, if not

avoided, could result in death or serious injury.

CAUTION

Caution! The signal word that indicates a hazard with a low level of risk which, if not avoided,

could result in minor or moderate injury.

NOTICE

Notice The signal word that indicates information considered important, but not hazard-related

(e.g.) messages relating to property damage).

The Dutch Powerhouse Empress (E 650 XXX YY), where XXX YY ZZ = where XXX =

LB (Low Blue) LBW (Low Blue + White),

MB (Medium Blue) MBW (Medium Blue + White),

HB (High Blue) HBW (Hight Blue + White),

XB (Extreme Blue) XBW (Extreme Blue + White) or

BS (Broad Spectrum) is compliant to the following standards:

cMETus listed (ANSI/UL)

• UL 1598

• CSA C22.2 No. 250.0-08

• Low Voltage Directive (LVD) 2014/35/EU

• Electromagnetic Compatibility Directive (EMC) 2014/30/EU

General

• Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU

• Eco Design Directive 2009/125/EG

Please check our website for our warranty policy.

For further information please contact:

Oreon

Lorentzlaan 6

3401 MX IJsselstein

The Netherlands

T +31 30 760 0660

E [email protected]

W www.oreon-led.com

–4 –V20200201E

TABLE OF CONTENTS

1 Product description 5

1.1 Intended use 5

1.2 Symbols used on the product 5

1.3 Main components 6

1.4 General dimensions 6

2 Technicalspecications 7

2.1 General LED xture specications 7

2.2 Cooling info light LED xture 7

3 Precautions and safety instructions 8

4 Installation 9

5 Initial starting 12

6 Maintenance and disposal 13

6.1 Maintenance 13

6.2 Disposal 13

7 Troubleshooting 14

Appendix I Water-cooling installation 15

–5 –V20200201E

1 PRODUCT DESCRIPTION

1.1 Intended use

The intended use of the LED xture is to stimulate plant growth by use of light. Typical environments for the

grow light are greenhouses and indoor growing facilities. The Dutch Powerhouse Empress (E 650 XXX YY)

can only be used with an active cooling system. This cooling system needs to be custom made by the

qualied certied professional installer.

The Dutch Powerhouse Empress (E 650 XXX YY) is mainly used in the horticultural industry.

The Dutch Powerhouse Empress (E 650 XXX YY) may only be used within the operating conditions as

specied in Paragraph 2.1.

The Dutch Powerhouse Empress (E 650 XXX YY) is referred to as the “LED xture” in this manual.

1.2 Symbolsusedontheproduct

Product is tested against EN62471

The symbol on the material, the accessories or packaging indicates that this LED

xture may not be treated as domestic waste. Dispose of the equipment through a

recycling centre that handles electronics and electrical appliances within the EU

and in other European countries which use separate collection systems for used

electronics and electrical appliances. By disposing of the equipment in the proper

way, you will be helping to prevent potential risks to the environment and public

health, which might otherwise be caused by improper handling of the discarded

equipment. Recycling of materials contributes to the conservation of natural

resources. Therefore, do not discard your old electrical and electronic equipment

via the domestic waste.

160

122

388

160

–6 –V20200201E

1.3 Main components

1. Power inlet connector

2. T-slots for mounting

3. Water-cooling inlet/outlet (Pipe thread ISO 228 G3/ 4”)

4. Glass cover

5. Aluminium enclosure

6. LED light source

1.4 General dimensions

6.30"/160

4.8"/122

15,28"/388

6,30"/160

3,15"/80

3,38"/86

3,39"/86

1.57"/40

1.4"/36

6.30"/160

4.8"/122

15,28"/388

6,30"/160

3,15"/80

3,38"/86

3,39"/86

1.57"/40

1.4"/36

Power consumption 655 W ± 5%, depending on model

Power factor > 0.96 @ 400 VAC

Supply voltage 200-480 VAC

Frequency range 50/60 Hz

Current range 3.5 - 1.5 A

Inrush current < max. 40 A (t< 1msec)

Leakage current < 0.75 mA @ 480 VAC

Recommended circuit breaker type-K trip characteristic

Ambient operating conditions 32 to 113°F | 0 to 45°C / 95% RH

Water-cooling inlet/outlet Pipe Thread ISO 228 G3/4”

Power inlet connector1Wieland RST20i3 male

Isolation class Class I

Ingress protection IP67 for LED module

Impact protection IK-10 (IK-7 for glass cover)

Net. weight 19.0 lb | 8,6 kg

LED xture dimensions (l x w x h) 15.35” x 6.3” x 4.8” | 390 mm x 160 mm x 122 mm

Heat imparted on the cooling liquid (W) 275-340 Watt (Depending on model)

Cooling liquid Water

Cooling liquid temperature From dew point to 113°F | 45°C

Direction of ow Can be both ways

Water connection 2x Pipe thread ISO 228-G 3

4” (26,4 mm)

Materials and corrosion Use pipe ttings of a material compatible with aluminium. Do not use

brass or steel ttings.

Water quality Ideally the cooling water should have a PH-value between 4 and 8 to

minimize any risk of corrosion.

Water ltration Contaminated water should be ltered for optimal performance and

cooling capacity of the light xtures. Oreon advises a lter of 300 micron

on the cooling system.

– 7 –V20200201E

2 TECHNICAL SPECIFICATIONS

2.1 GeneralLEDxturespecications

NOTICE

See the Technical Datasheet for more specications and properties of the LED xture.

2.2 CoolinginfolightLEDxture

1To order the female Wieland connector, please contact Oreon.

–8 –V20200201E

3 PRECAUTIONS AND SAFETY INSTRUCTIONS

DANGER

Follow proper grounding methods: The electrical system must be grounded. If you are not sure if your

power system is grounded, DO NOT install the LED xture. Contact a licensed electrician for information on

proper grounding methods as required by your local electrical code. FAILURE TO FOLLOW THIS WARNING

MAY LEAD TO DEATH, SEVERE INJURY, OR PROPERTY DAMAGE.

WARNING

• Ensure that the wiring meets the requirements in order to use the LED xture within the specications.

The LED xture is only suitable for a supply voltage of 200-480VAC.

• The LED xture may only be installed by a qualied person.

• Use a suitable circuit-breaker that is able to handle the high inrush current of the LED xture.

• Switch off the mains voltage before commencing installation or maintenance work.

• LED xture installation must comply with the current applicable standards.

• Never roll up cables and ensure that connection cables are kept separate. This helps to prevent

electromagnetic interference.

• The electrical power must be clean and have stable voltage and current and undistorted waveforms. The

LED xture contains a discrete surge protective device, but it is highly recommended to install suitable

surge protective devices in the electrical panels to prevent damage by surge events. Failure to ensure

power quality requirements will void warranty.

• The LED xture must be installed in accordance with your local electric code. Oreon recommends that

installation is only to be performed by a qualied electrician.

• Do not open or disassemble the LED xture. Opening the LED xture can prove hazardous and will void

the warranty.

• Never exert excessive pressure on the LED casing.

• The warranty does not cover damages caused by misuse or improper handling of the LED xture.

• Risk of eye injury! The high intensity light, produced by the LED xture, can cause severe damage to the

eye if viewed directly at close range. Avoid staring into the light or wear suitable protective eyewear.

NOTICE

The end user is responsible for ensuring correct installation and use of the LED xture. Incorrect installation

can cause damage or defects to the LED xture. The warranty will void if the LED xture and/or electronic

components are damaged due to incorrect installation.

–9 –V20200201E

4 INSTALLATION

BeforeinstallingtheLEDxture,makesurethat:

• The electrical system and water-cooling system are installed by the installer. These systems must be

custom made. Oreon advises to install the water-cooling system in a closed loop system according to the

Tichelmann conguration. It is highly recommended to consult a licensed mechanic/installer for the total

design of the cooling system. If any questions arise, please contact Oreon. See Appendix I Water-cooling

installation.

• You have chosen a mounting system which is suitable for the LED xture, the amount of LED xtures and

the installation area.

• You own a lighting plan of the installation area. The lighting plan is made by Oreon and determines the

number of LED xtures that will be used in an installation. Every lighting plan is customized to the specic

needs of our customers. The lighting plan determines where the grow lights will be located and species

the electrical system and water-cooling system.

1. Switch off the mains voltage.

2. Read the lighting plan and make sure you are familiar with it.

3. Gather the equipment for mounting the LED xture.

4. Mount the LED xtures with the chosen mounting system.

The LED xture has a water channel which makes it possible to cool the LEDs using water. The LED xture

has an inlet and an outlet to allow water ow through the lamp. The inlet/outlet are equipped with a

standard G 3/4” inner thread. Use a pipe tting with G 3/4” outer threading to connect the pipes to the inlet

and outlet.

ToconnecttheLEDxturetothewater-coolingsystem,followthestepsbelow:

5. Cut the tubes used to transport the cooling liquid to length. Connect the LED xtures using the tubes.

Calculate tube length? Note: thickness of the end plate and add 0.01” | 3,25 mm

0.01” |3,25 mm

–10 –V20200201E

ToconnecttheLEDxturetotheelectricalsystem,followthestepsbelow:

NOTICE

You can order the female Wieland connector from Oreon. Please contact Oreon for details.

6. Strip the appropriate length of cable. (x=8mm, y=30mm for PE wire & 25mm for N and L wires).

7. Crimp ferrule to the cable using the appropriate tool.

DANGER

Make sure to turn off the power before connecting the cable in the junction box.

8. Connect the wires of the electrical installation to the Wieland Female connector (torque typ. 0.8…1Nm).

Use the required cable types as specied in paragraph 2.1.

Inhaltsverzeichnis

Andere Oreon Beleuchtungsausrüstung Handbücher

Oreon

Oreon MONARCH M 1000 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung