Oriental motor BMU Series Bedienungsanleitung

Brushless Motor

QUICK START GUIDE

BMU Series

HM-5191-3

CN1 : 3 pin

CN4 : 9 pin

□Connector

□Motor

□Driver

□Mounting screw set

Package contents

Motor (sold separately)

The gure shows an

example of the

combination type.

∗Be sure to match the motor output power with the driver output power.

Supplied with the

combination type.

□OPERATING MANUAL

To connect the motor and driver, the dedicated

connection cable is always needed.

Connection cable (sold separately)

□QUICK START GUIDE

(this document)

CN1 : 3 pin

CN4 : 12 pin

• 30 W to 120 W • 200 W to 400 W

This document describes for when the motor is of the connector type.

The descriptions other than "connection for motor and cable" are

common to the BMU Series.

2 Operating a motor

Theﬁgureshowsthe

30Wto120Wdriver.

Thank you for purchasing an Oriental Motor product.

Use the product correctly after thoroughly reading the section "Safety precautions" of the operating manual.

This document describes methods till rotating the motor after connecting it to the driver.

For details about how to use the product, refer to the supplied with

the driver.

OPERATING MANUAL

The package includes the items shown below.

FWD

REV

FWD

REV

The gure is an example

for when the product is

of a single-phase 100 VAC.

FWD

REV

Rotation speed

0 r/min (standstill)

[ Example: 50 →1000 r/min ]

The motor rotates.

50 r/min (factory setting)

Setting dial

Operation switch

Set the operation switch to

Rotation

direction switch

Switch the motor rotation direction

using the rotation direction switch.

[ STAND-BY ]

[ RUN ]

FWD

REV

The motor stops.

To stop the motor

Start of motor

Change of motor speed

AC power ON

Power ON The display blinks

If the power supply is turned on while the operation switch

is set to the [RUN] side, the alarm is generated.

【How to reset 】Set the operation switch to [STAND-BY].

The alarm is reset, and the motor rotation

speed is displayed.

[ STAND-BY ]

Adjustment

Decelerate Accelerate

When the setting dial is

pressed, the display

changes to lighting

from blinking, and the

speed will be set.

When you start the

motor next time, it will

rotate at the set speed.

Press

When the setting dial is turned, the display blinks.

You can change the speed while blinking.

Set

ORIENTALMOTOR CO.,LTD.

Published in December 2019

1 Connecting

• Single-phase

100-120 VAC

• Single-phase

100-120 VAC

• Single-phase

200-240 VAC

• Single-phase

200-240 VAC

• Three-phase

200-240 VAC

• Three-phase

200-240 VAC

Motor

Driver

To power supply

Connect a power supply cable according to the power-supply voltage specications of the driver. Prepare the power supply cable since it is not supplied with the product.

Connection cable

CN3

CN1 CN1 CN1

CN1

This is an example for when the cable is "leading in direction of output shaft."

CN1 CN1 CN1

Ground

Insert the lead wire to the connector so that the tip part

(copper wires after stripping the insulation cover)

does not become loose.

The loose tip part (copper wires)

may cause short-circuiting,

leading to damage to

the product.

Note

Connection for motor and cable

1Remove

CN2

Grounding

Be sure to ground using the

Protective Earth Terminal .

Be sure to ground the product.

Failure to do so may result in electric

shock or damage to the product.

Static electricity may cause damage

to the product if the Protective Earth

Terminals are not grounded.

Note

Protective Earth

Terminal

Protective Earth Terminal

Connector cap

The 400 W type is indicated

L1, L2, and L3 only.

The connector cannot be inserted

if the locking lever is turned down.

Insert into CN1

2Attach

Be sure to turn down the locking

lever till the position shown in

the gure.

3Secure

10 mm

Insert the lead wire while pushing the button of

the orange color with a screwdriver.

Lead wire

Button of the

orange color

Screwdriver

AWG18〜14

（0.75〜2.0 mm2）

Locking

lever

Cable outlet in output

shaft direction

Cable outlet in opposite

to output shaft direction

Cable outlet in

vertical direction

Model: CC_____F Model: CC_____B Model: CC_____V

Prepare a grounding wire since

it is not supplied with the product.

AWG18〜14（0.75〜2.0 mm2)

30 W

120 W

200 W

400 W

Andere Handbücher für BMU Series

Andere Oriental motor Motor Handbücher

Oriental motor

Oriental motor PKP Series Bedienungsanleitung

Oriental motor

Oriental motor BLV Series Bedienungsanleitung

Oriental motor

Oriental motor K II Series Bedienungsanleitung

Oriental motor

Oriental motor SMK Series Bedienungsanleitung

Oriental motor

Oriental motor World K Series Bedienungsanleitung

Oriental motor

Oriental motor AR Series Bedienungsanleitung

Oriental motor

Oriental motor PK Series Bedienungsanleitung

Oriental motor

Oriental motor RK Series Bedienungsanleitung

Oriental motor

Oriental motor BMU Series Bedienungsanleitung

Oriental motor

Oriental motor K Series Bedienungsanleitung

Oriental motor

Oriental motor PK Series Bedienungsanleitung

Oriental motor

Oriental motor PKP Series Bedienungsanleitung

Oriental motor

Oriental motor 4IK25GN-AW2TJ Bedienungsanleitung

Oriental motor

Oriental motor US Series Bedienungsanleitung

Oriental motor

Oriental motor 2RK6GN-AM Bedienungsanleitung

Oriental motor

Oriental motor PKA Series Bedienungsanleitung

Oriental motor

Oriental motor CRK Series Bedienungsanleitung

Oriental motor

Oriental motor PK Series Bedienungsanleitung

Oriental motor

Oriental motor SPR II Series Bedienungsanleitung

Oriental motor

Oriental motor US Series Bedienungsanleitung

Oriental motor

Oriental motor BLE2 Series Bedienungsanleitung

Oriental motor

Oriental motor BH Series Bedienungsanleitung

Oriental motor

Oriental motor NX Series Bedienungsanleitung

Oriental motor

Oriental motor World K Series Bedienungsanleitung

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung