4
in the “S” position for Southern Hemisphere observers. Make
sure the motor is engaged, and turn the power switch on the
hand controller to the “ON” position. The LED in the center
of the hand controller should be shining green. Tighten the
mount’s R.A. lock knob. If properly polar-aligned, the mount will
now be tracking the motion of the night sky, and the telescope
should hold any astronomical object in its eyepiece steady over
time.
To move your telescope to a new object, loosen both the R.A.
and Dec. lock knobs and move the telescope until it is pointed in
the general direction of the object you wish to view. Retighten the
R.A. and Dec. lock knobs. Now, disengage the motor and use the
R.A. and Dec. slow-motion control cables to center the object in
the eyepiece’s field-of-view. Re-engage the motor, and the motor
drive system will keep the object centered over time. Remember,
never use the R.A. slow-motion control cable when the motor in
engaged, or you could permanently damage the motor.
There are four buttons on the hand controller. If no buttons
are pressed, the motor will turn the R.A. axis of the mount at
sidereal rate. If the bottom right button is pressed, the motor
will turn at 2x sidereal rate, which will cause objects viewed in
the telescope’s eyepiece to move slowly eastward. If the bot-
tom left button is pressed, the motor will stop turning (pause),
which will cause objects in the eyepiece to move slowly
westward. The bottom two buttons are most useful for guiding
purposes during long-exposure astrophotography.
Similarly, the top right button on the hand controller moves
objects in the telescope’s eyepiece quickly eastward, while
the top left button moves objects quickly westward.
For the EQ-1M, the top buttons move the mount at 8x sidereal
rate, while the EQ-2M’s top buttons move the mount at 4x
sidereal rate. The top two buttons are most useful for centering
an object within the field of view of an eyepiece.
Note that whenever any of the four buttons on the hand control-
ler are pressed, the LED in the center of the hand controller will
shine red; when the button is released, the LED will shine green
again.
5. Specifications
EQ-1M
Guiding rate: 100% sidereal
Centering rate: 800% sidereal
Power requirement: 6V DC
Battery type: four D-cell
Northern or Southern Hemisphere operation
Externally clutched
EQ-2M
Guiding rate: 100% sidereal
Centering rate: 400% sidereal
Power requirement: 6V DC
Battery type: four D-cell
Northern or Southern Hemisphere operation
Externally clutched
One-Year Limited Warranty
This Orion EQ-1M & EQ-2M Motor Drives are warranted against defects in materials or workmanship for a period of one year
from the date of purchase. This warranty is for the benefit of the original retail purchaser only. During this warranty period Orion
Telescopes & Binoculars will repair or replace, at Orion’s option, any warranted instrument that proves to be defective, provided it
is returned postage paid to: Orion Warranty Repair, 89 Hangar Way, Watsonville, CA 95076. If the product is not registered, proof
of purchase (such as a copy of the original invoice) is required.
This warranty does not apply if, in Orion’s judgment, the instrument has been abused, mishandled, or modified, nor does it apply
to normal wear and tear. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to
state. For further warranty service information, contact: Customer Service Department, Orion Telescopes & Binoculars, 89 Hangar
Way, Watsonville, CA 95076; (800) 676-1343.
Orion Telescopes & Binoculars
89 Hangar Way, Watsonville, CA 95076
Customer Support Help Line (800) 676-1343 • Day or Evening
